Dorex TECNICA DESIGN 200TS User manual

23/8"
60 mm
a b c d
200TS / 200TR DEADBOLT
Installation Instructions
MARK & DRILL HOLES2
To adjust the backset hold the faceplate and :
a. Turn the latch to the RIGHT or clockwise
(CW) for a 23/4" (70 mm) backset .
b. Turn the latch to the LEFT or counter-
clockwise (CCW) for a 23/8" (60 mm) backset.
CONVERT MORTISE LATCH TO DRIVE-IN
a. Use flat-head screw driver to pry the faceplate off the backplate
b. Rotate or twist the backplate clockwise.
c. Remove backplate from the latch.
d. Insert drive-in ring as shown until ring snaps into position.
INSTALL DEADBOLT LATCH (WOOD DOOR)
3
Insert latch in edge hole and
orient it vertically as shown.
Trace the outline of the
faceplate and remove the
latch.
Chisel 5/32" (4 mm) deep or
until the faceplate is flush with
the door edge.
FACEPLATE SIZE:
1 x 21/4" (25.4 x 57 mm)
Insert latch and secure with
screws. To avoid wood
splitting, drill pilot holes for
the screws first.
a. Close the door as shown
to mark the centerline of
the strike.
b. Transfer horizontal
centerline mark to the
inside surface of the frame
and measure one half (½)
the door thickness from
the door stop to locate
the vertical centerline of
the strike.
c. Drill a 1" (25.4 mm) hole
11/4" (32 mm) deep at the
intersection of the vertical
and horizontal centerlines.
d. Match strike screw holes
with vertical centerlines on
jamb and trace outline.
e. Chisel outline 1/16" (1.5 mm)
deep. Strike should be
flush with jamb surface.
FOR DRIVE-IN
Insert latch in to the hole as shown
until flush with door edge. Use a
rubber mallet or wood block and
hammer if necessary.
INSTALL STRIKE (WOOD FRAME)4
a, b c, d, e g
200TS-TR-INST 2018-03 1/2
REQUIRED TOOLS:
1. Phillips flat-head screwdriver
2. 1" (25.4 mm) chisel
3. 1" (25.4 mm) drill bit
4. 21/8" (54 mm) hole saw
Do not use power tools when
installing door harware,
excessive screw or bolt
tightening may affect installation
or functioning of the hardware.
ADJUST TO REQUIRED BACKSETADJUST TO REQUIRED BACKSET1
b
a
FACEPLATE
c
BACKPLATE
LATCH
DRIVE-IN
RING
d
a. Determine desired backset. Backset
on door should be the same as
backset of the deadbolt latch.
b. Determine the desired lock height
from the finished floor and mark the
lock's height centerline.
c. Fold template over door edge at
marked height and mark the center of
the 21/8" (54 mm) hole on door surface
at required backset and drill.
d. Determine thickness of the door and
make center mark for 1" (25.4 mm) on
the door edge and drill. Drill 31/32"
(25 mm) for drive-in installations.
NOTE: Drill the 21/8" (54 mm)
hole from BOTH SIDES of
the door to avoid splitting or
damaging the door surface.
f
FOR METAL FRAME
Prepare frame for 11/8x 23/4 x 1/16"
(29 x 70 x 1.6 mm) strike.
Insert strike and secure using
#8 x 11/8" (32 mm) combo screws
as shown.
Insert strike and secure using 3"
(76 mm) long wood screws and
#8 x 11/8" (32 mm) combo screws
as shown.
11/8x 23/4", 1/4" radius corners
29 x 70 mm, 6 mm radius corners
11/8x 23/4"
29 x 70 mm
LATCH
FACEPLATE
23/4"
70 mm
We recommend an
edge-bore of
31
/
32
" (25 mm)
diameter for a tighter fit.

FOR BACKSET
23/8" (60 mm)
FOR BACKSET
23/4" (70 mm)
21/8" (54 mm)
INSTALL DEADBOLT - SINGLE CYLINDER5
EXTERIOR CYLINDER
Tapped holes in the housing of exterior cylinder should be lined up with
the screw holes of the latch. Key hole should be in down position and
the tailpiece should be horizontal as shown.
INTERIOR THUMBTURN
Align interior thumbturn base plate with cylinder tailpiece and assemble
using supplied mounting bolts. Place square or round rose over the base
plate, then washer and tumbturn. Secure thumbturn with set screw.
200TS / 200TR DEADBOLT
Installation Instructions
200TS-TR-INST 2018-03 2/2
INSTALLATION WITH FIRECAN
a. Remove cylinder collar from
exterior cylinder.
b. Ensure spacer ring is
installed as shown.
The deadbolt requires modifcation prior to installation with a firecan on a
fire labelled wood door:
c. Flip cylinder collar as shown and
reassemble exterior mechanism.
FOLD HERE
PLACE ON DOOR EDGE
13/4
45
INCH
MM
19/16
40
13/8
35
Drill 1" (25.4 mm) hole on
door edge at the center of
the door thickness
Do not use template if not to scale.
To verify, confirm dimensions.
INSTALLATION TEMPLATE
Do not use power tools when installing
door harware, excessive screw or bolt
tightening may affect installation or
functioning of the hardware.
CYLINDER
COLLAR
SPACER
RING
FLIP
CYLINDER
COLLAR
SPACER
RING
d. Insert Firecan into 21/8" (54 mm)
hole as shown. You may have
to adjust the opening for a
proper fit.
e. Install exterior cylinder as
per Section 5.
f. Install interior thumbturn as
per Section 5. Ensure tabs
are INSIDE of the firecan.
ROUND OR
SQUARE
MODEL
ROUND OR
SQUARE
MODEL
ROUND OR
SQUARE
MODEL
Remove spacer ring inside the cylinder collar (see to the right).
It is only required for installations with a firecan.
TABS
CYLINDER
COLLAR
Firecan is NOT INCLUDED.
Must be ordered in conjunction with deadbolt.