Dorner AquaGard 7350 Series User manual

For other service manuals visit our website at:
www.dornerconveyors.com/manuals-literature
851-877 Rev. A Record Conveyor Serial Number Here
7350 Series Version 2
Modular Belt Conveyors
Installation, Maintenance and Parts Manual

Dorner Mfg. Corp. 2 851-877 Rev. A
7350 Series Version 2 Modular Belt Conveyors
Table of Contents
Introduction ......................................................................... 3
Warnings – General Safety.................................................. 4
Product Description ............................................................. 5
Specifications ...................................................................... 6
7350 Series Version 2 Modular Belt Conveyors ............. 6
Flat Belt 7350 Series Version 2.................................... 6
Cleated Belt 7350 Series Version 2.............................. 6
Flat Belt LPZ 7350 Series Version 2 ........................... 7
Cleated Belt LPZ 7350 Series Version 2 ..................... 7
Conveyor Supports .......................................................... 8
Specifications................................................................... 8
Installation ........................................................................... 9
Required Tools................................................................. 9
Recommended Installation Sequence .............................. 9
Conveyors Longer than 10 ft (3048 mm) ........................ 9
Connecting Components .............................................. 9
Z-Frame Conveyors ....................................................... 10
Upper Knuckles.......................................................... 10
Lower Knuckles ......................................................... 10
Stand Installation ........................................................... 11
Belt Installation.............................................................. 11
Belt Returns ................................................................... 12
Flat Belt Returns 610 mm Wide and Wider............... 12
Cleated Belt and Flat Belt Returns
Under 610 mm Wide .................................................. 14
Guide Installation........................................................... 15
High Side Guides ....................................................... 15
Adjustable Guides ...................................................... 16
Drive Package Installation ............................................. 17
Preventive Maintenance and Adjustment.......................... 18
Required Tools............................................................... 18
Checklist ....................................................................... 18
Cleaning ......................................................................... 18
Lubrication..................................................................... 18
Maintaining the Conveyor Belt...................................... 18
Troubleshooting ......................................................... 18
Conveyor Belt Replacement ......................................... 19
Conveyor Belt Tensioning ............................................. 19
Wear Strips .................................................................... 20
Wear Strip Removal ................................................... 20
Side Rail Wear Strip Replacement............................. 20
Drive Sprocket and Spindle Replacement ..................... 20
Nose Bar Drive Sprocket and Spindle Replacement ..... 22
Nose Bar Spindle Replacement.................................. 22
Nose Bar Drive Sprocket Replacement...................... 23
Idler Puck and Spindle Replacement ............................. 25
Nose Bar Idler Spindle Replacement............................. 26
Bearing Replacement..................................................... 27
Drive Bearing Removal and Replacement ................. 27
Maintenance of Knuckles .............................................. 27
Lower Knuckle........................................................... 27
Upper Knuckle ........................................................... 29
Belt Return Maintenance ............................................... 31
Flat Belt Returns 610 mm Wide and Wider............... 31
Cleated Belt and Flat Belt Returns
Under 610 mm Wide .................................................. 32
Notes.................................................................................. 33
Service Parts ...................................................................... 34
End Drive Tail ............................................................... 34
Nose Bar Drive Tail....................................................... 36
Idler Tail ........................................................................ 38
Idler Tail with Auxiliary Shaft ....................................... 39
Tip-Up Idler Tail ............................................................ 40
Nose Bar Idler Tail ......................................................... 41
Tip-Up Nose Bar Idler Tail ............................................ 42
Frame Assembly............................................................. 43
Upper Knuckle ............................................................... 44
Lower Knuckle ............................................................... 45
Connecting Assembly..................................................... 46
25 mm High Sides .......................................................... 47
75 mm High Sides .......................................................... 48
152 mm High Sides ........................................................ 49
Fully Adjustable Round Guides ..................................... 50
Tool-Less Fully Adjustable Round Guides .................... 51
Fully Adjustable Flat Guides.......................................... 52
Tool-Less Fully Adjustable Flat Guides ........................ 53
25 mm Cleated High Sides ............................................. 54
75 mm Cleated High Sides ............................................. 55
152 mm Cleated High Sides ........................................... 56
Flat Belt Returns 610 mm Wide and Wider ................... 57
Cleated Belt and Flat Belt Returns
Under 610 mm Wide ...................................................... 58
Ordering a Replacement Chain ...................................... 59
Flat Belt Chain Repair Kit.............................................. 59
Cleated Belt Chain Repair Kit........................................ 59
Return Policy...................................................................... 60

851-877 Rev. A 3 Dorner Mfg. Corp.
7350 Series Version 2 Modular Belt Conveyors
Introduction
Upon receipt of shipment:
• Compare shipment with packing slip. Contact factory
regarding discrepancies.
• Inspect packages for shipping damage. Contact carrier
regarding damage. Accessories may be shipped loose.
• See accessory instructions for installation.
The Dorner Limited Warranty applies.
Dorner 7350 Series conveyors have patents pending.
Dorner reserves the right to make changes at any time
without notice or obligation.
Dorner has convenient, pre-configured kits of Critical
Service Parts for all conveyor products. These time saving
kits are easy to order, designed for fast installation, and
guarantee you will have what you need when you need it.
Recommended Critical Service Parts and Kits are marked in
the Service Parts section of this manual with the Key Service
Parts symbol .
CAUTION
Some illustrations may show guards
removed. DO NOT operate equipment without
guards.

Dorner Mfg. Corp. 4 851-877 Rev. A
7350 Series Version 2 Modular Belt Conveyors
Warnings – General Safety
WARNING
The safety alert symbol, black triangle with white
exclamation, is used to alert you to potential
personal injury hazards.
DANGER
SEVERE HAZARD!
KEEP OFF CONVEYORS. Climbing, sitting,
walking or riding on conveyor will result in death
or serious injury.
WARNING
SEVERE HAZARD!
LOCK OUT POWER before removing guards or
performing maintenance. Exposed moving parts
can cause serious injury.
WARNING
BURN HAZARD!
DO NOT TOUCH the motor while operating, or
shortly after being turned off. Motors may be HOT
and can cause serious burn injuries.
WARNING
PUNCTURE HAZARD!
Handle drive shaft keyway with care. It may be
sharp and could puncture the skin, causing
serious injury.
DANGER
EXPLOSION HAZARD!
• DO NOT OPERATE CONVEYORS IN AN
EXPLOSIVE ENVIRONMENT. The electric
gearmotor generates heat and could ignite
combustible vapors.
• Failure to comply will result in death or serious
injury.
WARNING
CRUSH HAZARD!
• DO NOT place hands or fingers inside the
conveyor while it is running.
• DO NOT wear loose garments while operating
the conveyor. Loose garments can become
caught up in the conveyor.
• Failure to comply could result in serious injury.
WARNING
CRUSH HAZARD!
• SUPPORT CONVEYOR SECTIONS PRIOR TO
LOOSENING STAND HEIGHT OR ANGLE
ADJUSTMENT SCREWS.
• Loosening stand height or angle adjustment
screws may cause conveyor sections to drop
down, causing serious injury.
WARNING
SEVERE HAZARD!
• Dorner cannot control the physical installation
and application of conveyors. Taking protective
measures is the responsibility of the user.
• When conveyors are used in conjunction with
other equipment or as part of a multiple
conveyor system, CHECK FOR POTENTIAL
PINCH POINTS and other mechanical hazards
before system start-up.
• Failure to comply could result in serious injury.

851-877 Rev. A 5 Dorner Mfg. Corp.
7350 Series Version 2 Modular Belt Conveyors
Product Description
Refer to (Figure 1) for typical conveyor components.
Figure 1
Figure 1
1Conveyor
2 Guides (If Equipped)
3 Belt (Cleated Belt Shown)
4 Support Stands
5DriveEnd
6IdlerEnd
2
64
3
1
5

Dorner Mfg. Corp. 6 851-877 Rev. A
7350 Series Version 2 Modular Belt Conveyors
Specifications
7350 Series Version 2 Modular Belt Conveyors
Flat Belt 7350 Series Version 2
Cleated Belt 7350 Series Version 2
Conveyor Length
Drive Type
Idler Type
Drive Position
Conveyor Width
73B M WWW LLLLL D PA
Document Language
Profile A side
PD -
IA
Profile D side
Belt Type
-X12 4
Tail 4 Auxiliary Shaft Option
Auxiliary Shaft Exists
BB
Tail 3 Auxiliary Shaft Option
Tail 2 Auxiliary Shaft Option
Tail 1 Auxiliary Shaft Option
SS
Drive Stand Location
Idler Stand Location
3
Conveyor Length
Drive Type
Idler Type
Drive Position
Conveyor Width
73F M WWW LLLLL D P
Document Language
Profiles
BB -
IA
Cleat Type
Cleat Spacing
-X12 4
Tail 4 Auxiliary Shaft Option
Auxiliary Shaft Exists
SS
Tail 3 Auxiliary Shaft Option
Tail 2 Auxiliary Shaft Option
Tail 1 Auxiliary Shaft Option
SS
Drive Stand Location
Idler Stand Location
3

851-877 Rev. A 7 Dorner Mfg. Corp.
7350 Series Version 2 Modular Belt Conveyors
Specifications
Flat Belt LPZ 7350 Series Version 2
Cleated Belt LPZ 7350 Series Version 2
Drive Type
Idler Type
Drive Position
Conveyor Width
73B M WWW LLLL D
Document Language
Profiles
PP -
IA
Belt Type
-X12 4
Tail 4 Auxiliary Shaft Option
Auxiliary Shaft Exists
BB
Tail 3 Auxiliary Shaft Option
Tail 2 Auxiliary Shaft Option
Tail 1 Auxiliary Shaft Option
SS
Drive Stand Location
Idler Stand Location
3
-LLLL -LLLL AA E
Direction
Angle
L3 Section Length
L2 Section Length
L1 Section Length
Drive Type
Idler Type
Drive Position
Conveyor Width
73F M WWW LLLL D P
Document Language
Profiles
BB -
IA
Cleat Type
Cleat Spacing
-X12 4
Tail 4 Auxiliary Shaft Option
Auxiliary Shaft Exists
SS
Tail 3 Auxiliary Shaft Option
Tail 2 Auxiliary Shaft Option
Tail 1 Auxiliary Shaft Option
SS
Drive Stand Location
Idler Stand Location
3
-LLLL -LLLL AA E
Direction
Angle
L3 Section Length
L2 Section Length
L1 Section Length

Dorner Mfg. Corp. 8 851-877 Rev. A
7350 Series Version 2 Modular Belt Conveyors
Specifications
Conveyor Supports Figure 2
Figure 2
Specifications
Maximum Distances:
1 = Support Stand on Idler End = 762 mm (30")
2 = Between Support Stands = 2438 mm (8 ft)**
3 = Support Stand on Drive End = 610 mm (24")
** For conveyors longer than 3048 mm (10 ft),
install stand mount kit at frame joint.
1 2 23
Conveyor Width Reference (WWW) 203, 254, 305, 356, 406, 457, 508, 559, 610, 660, 711, 762, 813, 864, 914
Conveyor Belt Width 203 mm (8"), 254 mm (10"), 305 mm (12"), 356 mm (14"), 406 mm (16"), 457 mm (18"),
508 mm (20"), 559 mm (22"), 610 mm (24"), 660 mm (26"), 711 mm (28"), 762 mm (30"),
813 mm (32"), 864 mm (34"), 914 mm (36")
Maximum Conveyor Load
(See NOTE Below) 97 kg/ m2(20 lbs. / ft2) with a maximum of 340 kg (750 lbs.)
Belt Travel 305 mm (12") per revolution of pulley
Maximum Belt Speed 79 m/minute (260 ft/minute)
Conveyor Length Reference (LLLLL) 0915 – 25000 in 00005 increments
Conveyor Length 915 mm (36") - 25000 mm (984.25") in 5 mm (.20") increments
IMPORTANT
Maximum conveyor loads are based on:
• Non-accumulating product
• Product moving toward gearmotor
• Conveyor being mounted horizontally
• Conveyor being located in a dry environment
• Conveyor equipped with standard belt only

851-877 Rev. A 9 Dorner Mfg. Corp.
7350 Series Version 2 Modular Belt Conveyors
Installation
Figure 3
Figure 3
Required Tools
• Level
• Torque wrench
• 5/32" hex wrench
• 13 mm wrench
• 14 mm wrench
• 17 mm wrench
Recommended Installation
Sequence
1. Assemble the conveyor (if required). Refer to
“Conveyors Longer than 10 ft (3048 mm)” on page 9.
2. Attach the stands. Refer to “Stand Installation” on
page 11.
3. Install the belt. Refer to “Belt Installation” on page 11.
4. Install the gearmotor. Refer to “Drive Package
Installation” on page 17.
Conveyors Longer than 10 ft
(3048 mm)
Connecting Components
Typical connecting components (Figure 4).
Figure 4
Figure 4
1. Locate and arrange conveyor sections by section labels
(Figure 5, item 1).
Figure 5
Figure 5
2. Join both conveyor sections and install connecting
plates (Figure 4, item 1) with four M8x10 hex head cap
screws (Figure 4, item 2) on both sides.
CAUTIONCAUTION
Conveyor MUST be mounted straight, flat and
level within confines of conveyor. Use a level
(Figure 3, item 1) during setup.
11 Connecting Plate (x2)
2 Hex Head Cap Screw (x8)
3 Conveyor Frames
1
32
1
1

Dorner Mfg. Corp. 10 851-877 Rev. A
7350 Series Version 2 Modular Belt Conveyors
Installation
Z-Frame Conveyors
Upper Knuckles
1. Attach upper knuckle (Figure 6, item 1) to frame using
four bolts (Figure 6, item 2) and two plates
(Figure 7, item 1) on each side of the upper knuckle
assembly.
Figure 6
Figure 6
Figure 7
Figure 7
2. Tighten all bolts to 60 in-lb (7 Nm).
Lower Knuckles
1. Attach lower knuckle (Figure 8, item 1) to frame using
four bolts (Figure 8, item 3) and two plates
(Figure 9, item 1) on each side of the lower knuckle
assembly.
Figure 8
Figure 8
Figure 9
Figure 9
2. Tighten all bolts to 60 in-lb (7 Nm).
NOTE
Be sure all frame sections are properly
supported during Z-Frame assembly.
1
2
2
2
1
1
2
2
2
2
1
1

851-877 Rev. A 11 Dorner Mfg. Corp.
7350 Series Version 2 Modular Belt Conveyors
Installation
Stand Installation
Typical stand components (Figure 10).
Figure 10
Figure 10
1. Position the stands on a flat, level surface.
2. Attach the stands (Figure 11, item 1) to the frame.
Figure 11
Figure 11
Belt Installation
Typical belt components (Figure 12).
Figure 12
Figure 12
1. Position the belt on the conveyor frame (Figure 13).
Figure 13
Figure 13
2. Wrap belt around idler tail.
NOTE
For detailed assembly instructions, please
see support stand manual 851-885.
1 Conveyor Frame
2 Stand
3 Carriage Bolt (x4)
4 Hex Nut (x4)
1
2
3
4
1
1 Chain Belt
2 Belt Rod
1
1
1
2

Dorner Mfg. Corp. 12 851-877 Rev. A
7350 Series Version 2 Modular Belt Conveyors
Installation
3. Wrap the belt around the drive end of the conveyor.
Make sure that the sprocket teeth have engaged the belt,
with concave teeth (Figure 14, item 1) mating with
rounded section (Figure 14, item 2) of belt.
Figure 14
Figure 14
4. For Z-Frame conveyors, guide the belt under the hold
down guides (Figure 15, item 1) in the lower knuckle.
Figure 15
Figure 15
5. Bring the ends of the belt together (Figure 16).
Figure 16
Figure 16
6. Insert the belt rod (Figure 17, item 1).
Figure 17
Figure 17
7. Push the belt rod in as far as possible.
8. Lightly tap the head of the rod with a hammer until it
snaps into position.
Belt Returns
Flat Belt Returns 610 mm Wide and Wider
Typical return components (Figure 18).
Figure 18
Figure 18
2
1
1
1HexNut
2 Return Clip
3 Return Bracket
4 Carriage Bolt
5 Shaft
6 Retaining Plate
7 Spacer
8Puck
1
5
2
1
3
7
8
4
6

851-877 Rev. A 13 Dorner Mfg. Corp.
7350 Series Version 2 Modular Belt Conveyors
Installation
1. Install carriage bolt (Figure 19, item 1) through frame
rail.
Figure 19
Figure 19
2. Install return bracket (Figure 20, item 1).
Figure 20
Figure 20
3. Install return clip (Figure 21, item 1) and loosley secure
with nut (Figure 21, item 2).
Figure 21
Figure 21
4. Repeat on the opposite side of the conveyor.
5. Install belt return assembly (Figure 22, item 1) onto
return brackets (Figure 22, item 2).
Figure 22
Figure 22
6. Rotate return clip (Figure 23, item 1) down against
shaft (Figure 23, item 2) on both sides of conveyor.
Tighten nuts (Figure 23, item 3).
Figure 23
Figure 23
7. Check belt sag by measuring from the bottom of
conveyor frame (Figure 24). Belt sag should not exceed
2"(51 mm).
Figure 24
Figure 24
1
1
1
2
CAUTIONCAUTION
Belt sag should not exceed 2" (51 mm) from
the bottom of the conveyor frame.
12
1
2
3
Up to 2" (51 mm)

Dorner Mfg. Corp. 14 851-877 Rev. A
7350 Series Version 2 Modular Belt Conveyors
Installation
Cleated Belt and Flat Belt Returns Under
610 mm Wide
Typical return components (Figure 25).
Figure 25
Figure 25
1. Install carriage bolt (Figure 26, item 1) through frame
rail.
Figure 26
Figure 26
2. Install return bracket (Figure 27, item 1).
Figure 27
Figure 27
3. Install return clip (Figure 28, item 1) and loosley secure
with nut (Figure 28, item 2).
Figure 28
Figure 28
4. Repeat on the opposite side of the conveyor.
5. Install each puck (Figure 29, item 1) onto return
bracket (Figure 29, item 2) with stub shaft
(Figure 29, item 3) and spacer (Figure 29, item 4).
Figure 29
Figure 29
1 Spacer
2Puck
3 Stub Shaft
4HexNut
5 Return Clip
6 Return Bracket
7 Carriage Bolt
1
234
5
76
1
1
1
2
4
2
13

851-877 Rev. A 15 Dorner Mfg. Corp.
7350 Series Version 2 Modular Belt Conveyors
Installation
6. Rotate return clip (Figure 30, item 1) down against stub
shaft (Figure 30, item 2) on both sides of conveyor.
Tighten nuts (Figure 30, item 3).
Figure 30
Figure 30
7. Check belt sag by measuring from the bottom of
conveyor frame (Figure 31). Belt sag should not exceed
2"(51 mm).
Figure 31
Figure 31
Guide Installation
High Side Guides
1. Remove and discard the top bolt (Figure 32, item 1)
from the conveyor side.
Figure 32
Figure 32
2. Assemble the mounting block (Figure 33, item 1) to the
conveyor side with the bolt (Figure 33, item 2)
provided with the mounting block.
Figure 33
Figure 33
CAUTIONCAUTION
Belt sag should not exceed 2" (51 mm) from
the bottom of the conveyor frame.
1
2
3
Up to 2" (51 mm)
1
1
2

Dorner Mfg. Corp. 16 851-877 Rev. A
7350 Series Version 2 Modular Belt Conveyors
Installation
3. Install guide (Figure 34, item 1) into the slot
(Figure 34, item 2) of the mounting block and tighten
bolts (Figure 34, item 3).
Figure 34
Figure 34
4. Install the connecting plate (Figure 35, item 1) over the
studs.
Figure 35
Figure 35
5. Install nuts (Figure 36, item 1) and tighten.
Figure 36
Figure 36
Adjustable Guides
1. Remove the top bolt (Figure 37, item 1) and loosen the
bottom bolt (Figure 37, item 2).
Figure 37
Figure 37
2. Install the guide post (Figure 37, item 3) behind lower
bolt. Reinstall top bolt and tighten bolts.
3. Install guide rail (Figure 38, item 1) into rail clamp.
Tighten fastener to secure (Figure 38, item 2).
Figure 38
Figure 38
1
2
3
3
1
1
NOTE
See pages 50 to 53 for detailed view of guide
assembly.
1
2
3
2
1

851-877 Rev. A 17 Dorner Mfg. Corp.
7350 Series Version 2 Modular Belt Conveyors
Installation
Drive Package Installation
For detailed assembly instructions, refer to the appropriate
drive package manual:
• 851-881 7350 Series Version 2 Side Mount Drives
• 851-882 7350 Series Version 2 Nose Bar Drives
• 851-883 7350 Series Version 2 Bottom Mount Drives
1. Attach the motor (Figure 39, item 1) to the gear reducer
(Figure 39, item 2).
Figure 39
Figure 39
1
2

Dorner Mfg. Corp. 18 851-877 Rev. A
7350 Series Version 2 Modular Belt Conveyors
Preventive Maintenance and Adjustment
Required Tools
•1/8"hex wrench
•3/8"wrench
• 4 mm hex wrench
• 5 mm hex wrench
• 6 mm hex wrench
• 8 mm hex wrench
• 13 mm wrench
• Punch and hammer (to remove belt rod)
• Flat head screwdriver
Checklist
• Keep critical service parts on hand. Refer to the "Service
Parts" section starting on page 34 for recommendations.
• Replace any worn or damaged parts.
Cleaning
Lubrication
No lubrication is required. Replace bearings if worn.
Maintaining the Conveyor Belt
Troubleshooting
Inspect conveyor belt for:
• Surface cuts or wear
• Skipping
Damage to belt links or rods, surface cuts and / or
wear indicate:
• Sharp or heavy parts impacting belt
• Jammed parts
• Accumulated dirt
• Foreign material inside the conveyor
• Improperly positioned accessories
Skipping indicates:
• Excessive load on belt
• Worn spindle or impacted dirt on drive spindle
NOTE
Proper conveyor application, cleaning, and
sanitation are the responsibility of the end user.
CAUTIONCAUTION
Dorner recommends cleaning all the “food
zones” prior to placing conveyor into service.
Ensure adequate access is provided for
cleaning and servicing equipment so that the
required level of hygiene can be maintained.
WARNING
SEVERE HAZARD!
LOCK OUT POWER before removing guards
or performing maintenance. Exposed moving
parts can cause serious injury.

851-877 Rev. A 19 Dorner Mfg. Corp.
7350 Series Version 2 Modular Belt Conveyors
Preventive Maintenance and Adjustment
Conveyor Belt Replacement
1. Remove guides (Figure 40, item 1) when required.
Figure 40
Figure 40
2. Use a punch and hammer to push the belt rod out by
striking the rod end opposite the retaining head
(Figure 41).
Figure 41
Figure 41
3. Slide the old belt off the conveyor frame.
4. Replace the old belt with a new one. Refer to “Belt
Installation” on page 11.
Conveyor Belt Tensioning
1. Remove one or more belt links to take up tension.
Figure 42
Figure 42
WARNING
SEVERE HAZARD!
LOCK OUT POWER before removing guards
or performing maintenance. Exposed moving
parts can cause serious injury.
CAUTIONCAUTION
DO NOT reuse belt rods that are damaged or
show signs of wear.
1
WARNING
SEVERE HAZARD!
LOCK OUT POWER before removing guards
or performing maintenance. Exposed moving
parts can cause serious injury.
NOTE
Belt should not be stretched during
installation. A proper length of belt can be
installed by interlocking the ends by hand
without excess links.
CAUTIONCAUTION
Belt sag should not exceed 2" (51 mm) from
the bottom of the conveyor frame (Figure 42).
Up to 2" (51 mm)

Dorner Mfg. Corp. 20 851-877 Rev. A
7350 Series Version 2 Modular Belt Conveyors
Preventive Maintenance and Adjustment
Wear Strips
Replace the wear strips if they become worn.
Typical standard wear strips (Figure 43).
Figure 43
Figure 43
Wear Strip Removal
1. Remove conveyor belt. Refer to “Conveyor Belt
Replacement” on page 19.
2. Remove worn wear strips (Figure 44, item 1) from the
frame notches.
Figure 44
Figure 44
3. Attach new wear strips by installing the locating hole
(Figure 44, item 2) over the tab (Figure 44, item 3) on
the crossmember.
Side Rail Wear Strip Replacement
1. Remove two self-tapping screws (Figure 45, item 1)
retaining the wear strip to the frame.
Figure 45
Figure 45
2. Remove the wear strip (Figure 45, item 2) from the
frame rail.
3. Replace with new wear strip.
Drive Sprocket and Spindle
Replacement
1. Remove the gearmotor. For detailed instructions, refer
to the appropriate drive package manual.
2. Open conveyor belt. Refer to “Conveyor Belt
Replacement” on page 19.
1 Side Wear Strips
2 Center Wear Strips
NOTE
Rounded end of the wear strip must face up.
2
1
1
2
3
WARNING
SEVERE HAZARD!
LOCK OUT POWER before removing guards
or performing maintenance. Exposed moving
parts can cause serious injury.
WARNING
PUNCTURE HAZARD!
Handle drive shaft keyway with care. It may
be sharp and could puncture the skin,
causing serious injury.
1
2