Dorner 62MD1132 User manual

62MD1132 or 62MD1134R DC Controller
Mounting on Dorner Conveyors and Stands
Assembly Instructions
DMC-PD1298 Dorner Mfg. Corp. 851-309 Rev. B
B
G
D
C
Components As Shipped
EF
AH
I
Illustration References
A 62MD1134R or 62MD1132 DC Controllers
B (2) 6100 Series Accessory Mounting Clips
(450186M)
C Socket Head Screws, M5 x 8 mm (4)
D Socket Head Screws, M6 x 16 mm (2)
E (2) T-Bars (639971M)
F Socket Head Screws, M6 x 20 mm (2)
G (2) Spring Nut, M6 (990605M)
H (2) Controller Mounting Bar (300459)
I (2) Controller Cover Mounting Screws
J 4 mm hex key wrench (not supplied)
K Screwdriver (not supplied) being used to align
T-bar while inserting screw
To prevent injury, make sure all electrical power
sources have been disconnected and locked-out
before you perform any assembly or adjustments.
NEVER operate equipment without guards or other
protective devices properly secured in place.
Ç
Ç
Conveyor Mounting
Step 1: Remove cover by loosening mounting
screws (I). Use mounting screws (C), to attach
mounting bars (H) as shown.
A
C
I
H
Step 2a: Mount T-bar in 2100 Series (left) and 3100
Series (right) conveyor T-slots as shown.
E
E
Step 3a: Secure box to 2100 Series conveyor by
installing M6 Screws (D). (3100 Mounting Similar)
D
B
Step 2b: Accessory clips positioned on 6100
Series conveyor.
Step 3b: Secure box to 6100 Series conveyor by
installing M6 Screws (F) through holes in
mounting bars (H) and into accessory clips (B).
F
BH
<continued on next page>

62MD1132 or 62MD1134R DC Controller
Mounting on Dorner Conveyors and Stands Assembly Instructions
851-309 Rev. B Dorner Mfg. Corp. DMC-PD1298
Stand Leg Mounting
Bar Attachment for Vertical Mounting
Step 1: Remove cover by loosening mounting
screws (I). Then, properly orient and attach the
mounting bars (H) in the “stand leg mounting”
position. Attachment details similar to Step 1 on
opposite side of this page.
H
Aluminum Stand Legs
Step 1: Install 1st T-bar (E), insert screw (D)
through hole in bottom mounting bar (H) and,
using 4 mm hex key wrench, partially thread into
one T-bar.
D
H
Step 2: Temporarily fix controller mounting
position by tightening screw (D). Then, insert 2nd
T-bar (E) into T-slot as shown.
E
D
NOTE: For electrical wiring or troubleshooting, refer
to information provided by controller manufacturer.
Step 3: Using screwdriver, raise 2nd T-bar (E) to
align it with hole in the top mounting bar and in-
sert a screw (D) and partially thread into T-bar as
shown.
J
K
D
D
Step 4: Slide controller to its desired mounting
location and tightly secure both screws (D).
Steel Stand Leg
Step 1: Properly orient and install spring nuts (G)
as shown. Then, secure controller by installing
two (2) M6 x 20 screws (F). Adjust controller
position and secure the M6 screws.
F
G
For replacement parts, contact an autho-
rized Dorner Service Center or the factory.
851-309 Rev. B Printed in U.S.A.
975 Industrial Ave, PO Box 20
Hartland, WI 53029-0020 USA
Dorner Mfg. Corp. reserves the right to change or
discontinue products without notice. All products and
services are covered in accordance with our standard
warranty. All rights reserved. Dorner Mfg. Corp. 1997
USA
TEL [phone] (USA)
FAX [phone] (USA)
Outside the USA
TEL [phone],
FAX [phone]
DORNER MFG. CORP.
Internet: www.dorner.com