Doulton Ceramic Twin Undersink Operating and safety instructions

Shut Off the Water Supply - Locate the water ministop valve (see Diagram 3) for the cold water feed line. (To identify
the hot and cold water pipes, turn on the hot water at the faucet. After the water is warm to the touch, feel the pipes
under the sink).
Close the cold water ministop valve. Turn on the cold water at the
faucet to assure that the line is completely shut off and drained. (If
there is no cold water ministop valve located under the sink, it is
necessary to turn off the main water supply at the entry to the house).
Step by Step Installation
PLEASE READ THIS MANUAL CAREFULLY BEFORE INSTALLATION
Diagram 1 - Undersink Setup
Quick Fit Connector
for 1/4” Blue Tube
Feed Water
Shut-off Valve
1/2” Swivel
Compression Tee
1/2” Braided Hose (to
mixer/kitchen faucet)
Ministop
Valve
Cold Water
Diagram 2
Installing your undersink system - Taking into consideration ease of maintenance, nd a convenient location
beneath the benchtop. Using the selftapping screws provided, attach the lter to the cupboard wall (allowing approx
50mm height for servicing). The system may otherwise stand freely on the cupboard oor.
1
2
3Attach Swivel Compression Tee (see Diagram 2) - Unscrew braided
hose from ministop valve. Screw in the swivel compression tee.
Reattach braided hose.
Included Parts
WARNING: This unit must be installed on the COLD water line.
4Connect the System - To make a connection, the tube is simply
pushed in by hand. Please refer to Diagram 3. Where possible, leave
tubing long, do not cut to an exact length. Ensure cut is straight and
square with a clean surface.
CONGRATULATIONS on your purchase of the Doulton Ceramic Twin Undersink system.
With proper installation and maintenance of this unit you will enjoy many years of reliable service, providing you
and your family with genuine sub-micron, premium ltered water.
1
2
3
4
5
6
Specications
Filter Output 5000 litres
Max Flow Rate 3 litres p/min
Dimensions (cm) 23(W) x 32(H) x 13(D)
Warranty 5 years*
Micron Nominal
Micron Rating
0.2
Doulton Ceramic Twin Undersink
Installation & Maintenance Guide Instructions
A
see Diagram 2 2
3
4
5
7B
6
1
A
B1/4” blue tube connects the Carbon Block Post Filter to the chrome
faucet.
Chrome Faucet
Housing
Stainless Steel Bracket
Tee Piece
PLV
Blue Tube
Screws
Red Clips
1/4” blue tube connects the feed water valve to the Pre-Filter.
7
*Warranty Terms & Conditions apply. For more information
go to www.watershop.com.au.
For more information go to www.watershop.com.au

Faucet Installation
The pure water faucet may be installed on any at surface
over 50mm (2”) in diameter. (Remember: check the
underside of the location for interference). Make a small
indent using a centre punch to mark the desired drilling
location. Drill a pilot hole with a metal drill. Enlarge the
hole using a ½” metal drill bit.
Once the hole has been drilled install the faucet as per
Diagram 4. Be sure the faucet body, chrome plate, and
the black rubber washer are placed above the sink.
Install the black locating washer, the lock washer and nut
underneath, then tighten rmly while aligning faucet in
the desired direction.
Install female Quick Fit Connector to the end of the faucet
(see Diagram 4).
5
To make the connection,
push the tube rmly into
the connector.
Make sure the tube is
pushed as far as it can go
and secure with a John
Guest red clip.
To remove the tube - rst, remove
the red clip and then use two ngers
to push onto the collet and at the
same time pull out the tube.
1 2 3
Diagram 3 - Tube Connections
Collet
Tube
Red Clip
Activating the System for the First Time - Once all tubing has been connected, place the pure water faucet in the on
position, then open the ministop valve slowly. This will allow any trapped air to escape. Check plumbing assembly and
the undersink system are secure and free from leakage.
If there are no detected leaks, leave the pure water running for a few minutes to ush the new lter cartridges. Water
may be slightly discoloured and have some aeration, this is normal and will clear shortly.
Allow the system to stand for 2 to 3 hours and then ush again for several minutes. Your system is now operational.
6
PLEASE READ THIS MANUAL CAREFULLY BEFORE INSTALLATION
Mounting Plate
Black Rubber
Washer OR O-ring
Black Locating
Washer
Quick Fit
Connector to
Blue 1/4” Tube
Benchtop
Lock Washer
Blue 1/4” Tube
Nut
Diagram 4 - Your choice of designer faucet
Red Clip
Chrome
Faucet
Doulton Ceramic Twin Undersink
Providing great tasting pure water for over 30 years...
• Raise pH - Ideal for those who are looking to reduce acidic toxic
waste in the blood, tissues and uids of the body.
• Add Ionic Organic, Natural Minerals
• Lower ORP (Oxygen Reduction Potential) - enhance potent anti-oxygenating qualities.
Interested in Alkaline Water?
Add a AlkaHydrate Filter to your system
SHOWROOM 425 Miller Street, Cammeray NSW 2062
Tel: [phone] Fax: [phone]
Email: [e-mail]
SHOWROOM 342-350 Parramatta Road, Stanmore NSW 2048
Tel: [phone]
www.watershop.com.au