DQ Vela Electric User manual

Vela Electric Instructions
Please unpack your delivery carefully and inspect the radiator and contents –any
damages or shortages must be notified to your supplier within 3 days of delivery of
your goods.
SPECIFICATIONS FOR VELA ELECTRIC RADIATOR
Power Supply:
230V 50Hz +/-10%
Power control type:
RELAY 10A, TRIAC 10A, TRIAC 4A
Max power:
2000W total (Relay + TRIAC 1 + TRIAC 2)
Insulation class:
Class II
Environment protection classification:
IPX4
Operating temperature:
0 –50°C
Storage temperature:
-20 –85°C
NTC sensor:
10KOhm @25°C
Connection type:
Screw header 2,5mm2
Regulation type:
(Relay) Hysteresis +/- 0,5°C –(Triac) PID
Temperature settings range:
7–31°C
User interface type:
Push-button, potentiometer
Visualization interface:
STN LCD display, viewing angle 12 o’clock, red back-
light

Display and symbol description
1. Mode not required
2. Comfort mode.
3. Night reduction mode
4. Antifreeze mode
5. Temperature display
6. Clock display
7. Weekly Chrono mode
indicator
8. Stand-by indicator
9. Daily program bar
STAND-BY
MODE
Wall Brackets –Offer up the radiator in the desired position, mark the bracket
positions and fixing holes. The radiator should be placed a minimum of 10cm from
the floor. Using the appropriate drill and fixings attach the brackets to the wall. After
installing the plastic inserts into the hook part of the bracket the radiator can then be
hung from the brackets
INSTALLATION and FIXING

THERMOSTAT INSTRUCTION MANUAL
Please note: The clock needs to be set before use.
Setting
the clock
Setting the clock can only
be done while the unit is in
“stand by “mode.
Press and hold the mode
button until SET appears
on the screen, then press
the + - buttons to advance
the time, holding down the
buttons will advance the
time more quickly. Once
the time is set press the
mode button to confirm.
You will then need to
select a day from 1 to 7 by
pressing + - buttons to
scroll and mode button to
confirm.
Standby
Mode
To turn the unit on or enter
“stand by” mode Press and
Hold the stand by button
for 2 seconds. When in
“stand by” the red light at
the bottom left of the
screen will be lit, when the
unit is on the green button
will be showing.
Program
Mode
When the unit is turned on
and in program mode
(with the arrow pointing to
the sun or moon and clock
symbols at the same time)
the temperature can only
be set by selecting the
required temperature in
Comfort and Night modes.
Comfort
Mode
To enter this mode, push
the mode button until the
arrow is pointing to the
sun symbol only.
In this setting the
temperature will be
regulated to the value set
on the screen. The
temperature can be
adjusted by using the +
and –buttons on your
controller.
Night
Mode
To enter night mode - push
the mode button until the
arrow is pointing to the
moon symbol. The
reduced temperature can
be adjusted using the +
and - buttons.
Antifreeze
Mode
To enter the antifreeze
mode - push the mode
button until the arrow is
pointing to the snow flake
symbol. The unit will be
activated if the
temperature falls below 7
degrees C.
Setting
the
program
Mode
24H / 7
day.
To set the daily thermostat you must be in a programme mode (this is
shown by the arrow pointing to the sun or moon and clock symbols at
the same time).
Push and hold the mode button for 5 seconds until “PRO” is shown on
the screen.
Scroll using the + - buttons to select the day (D1 = Monday through to D7
= Sunday) pressing mode button to confirm.
Push the mode by button to enter the programme mode for that day.
Please note the lines on the left-hand side of the unit, when there is a
line the program will be in comfort mode and when there is not, it will
be in night mode. The time is also shown on the controller for reference.
Press the + button to set when you would like the program to be comfort
and –button for night mode.
Push and hold the mode button to return to day selection and repeat for
each day. Press mode to return back to the program when complete.

TERMS AND CONDITIONS
You must immediately remove all packaging, inspect the goods and notify us of any damage to the goods within 3 days
of delivery. We shall have no obligation to replace or repair damaged goods in the event of failure by the Buyer to
comply with this provision. Radiators which are off an unacceptable standard or are damaged must not be installed.
If any items are installed it will be treated as being as accepted as received.
Damaged goods being returned will only be collected from your delivery address, unless otherwise agreed in writing.
Any other goods, which we accept back, are to be returned by you to our place of business at your expense.
Items will be accepted as a return which have not been installed or damaged after delivery. We do not accept liability
for any damages sustained after delivery. Goods should be returned in their original packaging, provided such
packaging and goods are undamaged.
We may issue a credit note for goods which we accept as returned.
We may agree to provide you with replacement goods prior to collecting or receiving back the goods to be returned
(whether faulty, damaged or otherwise) but only on the condition that: the replacement goods are paid for in full and
we reserve the right to re-invoice you in the event that the returned goods are found to be in a worse condition than
when they were originally received by you or where such goods have not been received back to us within 3 months of
the replacement goods being received by yourselves. A re-stocking charge of 30% will be applied to all non-faulty stock
items that wish to be returned. Special order and non-stock products cannot be cancelled. Where cancellation or
alteration of orders is accepted by us, you may be required to pay a restocking charge, to cover administrative costs
and collection costs (if applicable); such charges to be determined by us. If the goods we deliver are faulty or damaged,
we will meet the cost of the return, if the fault is reported to us within 3 workingdays.
The goods will be deemed to have been accepted when they have been delivered and we may not accept claims for
any visible defects found after installation.
We accept no liability for any cost incurred relating to the cost of installation.
We shall not be liable for any plumber’s costs, decorator’s costs, transport costs, late penalties, or any other costs, as
a direct or indirect result of (i) any defect in the goods (including but not limited to any manufacturing faults, such as
leaks, that become apparent on or after installation) or (ii) late delivery of the goods.
GUARANTEES AND LIABILITIES –we are not the manufacturer of this product we will take all reasonable endeavours
to make over to you the benefit of any warranty or guarantee given by the manufacturers. The item must have been
fitted in accordance with British and or European standards as well as these fitting instructions.
PLEASE NOTE: That in accordance with Part L1 2006 of the Building Regulations and BS7593:1992 code of practice
for the treatment of hot water and central heating systems, we recommend flushing the heating system before
installation of new radiators and then adding the correct quantity and type of inhibitor for use with the radiator
and system to prevent corrosion. Damage caused to systems not protected by a suitable inhibitor will not be
covered by the manufacturer warranty. It is the responsibility of the installer to ensure the correct use and
suitability of the fixings provided. No liability for costs or damages arising from failure to do so can be accepted.
www.dqheating.com [e-mail] 01842 810833