Dr.Shrink+ Rapid Shrink 100 User manual

R
S
315 Washington St.
Manistee, Michigan
49660-1855
CONTACT OUR WORLD CLASS CUSTOMER SERVICE
[phone]
[phone]
[phone]
www.dr-shrink.com
[e-mail]
P:
P:
F:
MANUAL
YOUR COMPLETE OWNERS MANUAL
FOR THE RAPID SHRINK 100 (RS-100) HEAT TOOL
100

INTRODUCTION
The Rapid Shrink 100 (DS-RS100) Heat Tool is a propane red device to heat our premium
shrink wrap lm. It is self-igniting, lightweight, and economical compared to other heat tools
on the market. The Rapid Shrink 100 heat tool is ideal for beginners to experts and has an
output 100,000 BTUs.
WHAT’S INSIDE
The Rapid Shrink 100 heat tool kit includes:
1. Heat Tool Body
2. 25’Propane Hose
3. Adjustable Regulator
4. Carrying Case
5. Safety Glasses & Gloves
6. Training Literature
The Rapid Shrink 100 (DS-RS100) operates with an open ame. It must be used with caution
and common sense. Review all of the general safety information prior to initial use.
IMPORTANT:
1. This tool must never be used while under the inuence of drugs or alcohol.
2. It must never be pointed at other living beings.
3. Do not look down the combustor of the DS-RS100 when it is attached to the propane hose.
4. Always wear long cu safety gloves and safety glasses while operating the tool.
5. Misuse of this device can result in serious injury.
BEFORE AND AFTER EACH USE:
1. Inspect hose before each use for breaks or weakened spots.
2. Always shut o valve at tank when leaving the gun unattended for any length of time.
WARNING:
Please note that the shrink wrap you will be heating with the DS-RS100 can burn unless you are
specically using ame retardant shrink wrap. If heat is applied incorrectly, shrink wrap can
ignite into open ame. It can also drop down onto other combustible material and cause
secondary ignition and re. If at any time you observe the shrink wrap on re, immediately stop
what you are doing and carefully inspect the area where you are working for a possible re. Keep
a re extinguisher available at all times. Do not shrink wrap if the wind is over 10 mph.
Two types of tanks are commonly available: liquid withdrawal and vapor withdrawal. It is
crucial to use the vapor withdrawal type. Never try to run the gun on a liquid withdrawal tank.
Using a liquid withdrawal tank will clog the orice lter and may result in an extremely
dangerous long ame.
Tanks are available in 6, 8, 10, 20, 30, and 40 lb. sizes. The gun will run on a 6 lb. tank if used
only intermittently. Larger tanks should be chosen for continuous use. Smaller or nearly
empty tanks ice up faster than large, full tanks.Typically, a full 30 lb. tank, if run continuously,
will run 90 minutes before it ices up. If the production rates demand continuous use, the
following methods may be employed: Multiple tanks. Switch the gun from one tank to anoth-
er; Fan. An ordinary desk fan at the tank. The air ow around the tank will keep it from
icing up.
Introduction to your Rapid Shrink 100 Heat Tool .................................................................. 2
General Safety Information .................................................................................................. 3
Which Tank To Use ................................................................................................................ 3
HeatTool Operation ..............................................................................................................4
Troubleshooting ................................................................................................................... 5
RS100 Parts Index ................................................................................................................ 6
Warranty .............................................................................................................................. 7
Contact Dr. Shrink ................................................................................................................. 8
R
S
TABLE OF CONTENTS
GENERAL SAFETY
PROPANE TANKS
2 | Dr-Shrink.com Rapid Shrink 100 Owner’s Manual | 3
100

10
1
3
2
4
6 7
8 9
5
CONNECTIONS:
Connect the gun, hose and regulator to the tank using a wrench to tighten the ttings which all
have left hand threads.
START-UP:
After all connections are made and checked for leaks, the gun is ready for use. Turn regulator
rmly down clockwise, then turn back one turn counter clockwise. (Pressure will increase by
turning the regulator clockwise, and will decrease by turning counter clockwise). Open the tank
valve. Wait approximately 5 seconds to fully pressurize the hose. To start the gun, squeeze the
trigger slowly all the way until the igniter res with an audible click. CAUTION GUN WILL
IGNITE.
NOTES:
1. It is important to squeeze the gas trigger slowly. If the gas trigger is squeezed too quickly,
the igniter will re the spark plug before the gas mixture gets there.
2. Should the gun fail to re fully, release the trigger fully to assure that the igniter is reset and
repeat the starting procedure.
The majority of the problems arise from using a liquid withdrawal instead of a vapor withdraw-
al tank. CHECK THIS ITEM FIRST.
Valve screw not adjusted properly Without depressing the trigger, turn
valve adjustment screw clockwise till
gas is releasing. Then turn the screw
back 1/4 turn.
Trigger not depressed fully Depress trigger all the way until igniter
res with a click.
Handle activated too quickly Squeeze trigger slowly to make sure
mixture has entered combustor before
ring.
Pressure too low Check Regulator.
Trigger not released fully Release the trigger to make sure the
igniter is reset.
Defective igniter or connections Check for spark. Call for service options.
UNDERSTANDING THE HEAT TOOL:
HEAT TOOL OPERATION
TROUBLESHOOTING
4 | Dr-Shrink.com Rapid Shrink 100 Owner’s Manual | 5
CONTROLS:
No. Part Function
1 Trigger Activates gas valve and ignition wire
2 Valve* Open fuel ow
3 Valve Adjustment Screw Sets pressure
4 Igniter Fires ignition wire
5 Fuel Line* Carries fuel to orice
6 Orice* Meters fuel
7 Body Carries the fuel to the combustor to be ignited
8 Ignition Wire Connects to the spark plug to create ignition
9 Spark Plug Ignites mixture
10 Combustor Source where ame is lit
* Parts 2, 5, & 6 are one connected unit
PROBLEM PROBABLE CAUSE REMEDY
Gun won’t re

6 | Dr-Shrink.com Rapid Shrink 100 Owner’s Manual | 7
1 Trigger
2 Valve*
3 (this number is intentionally blank)
4 Igniter
5 Fuel Line*
6 Orice*
7 Body
8 Ignition Wire
9 Spark Plug
Gas not on Check ON/OFF valve.
Wrong fuel Check for proper tank.
TROUBLESHOOTING
PARTS INDEX
WARRANTY
PROBLEM PROBABLE CAUSE REMEDY
Gun won’t re
(cont’d)
Tank has iced up and tank pressure is Change to new tank.
below 15 PSIG.
Excess ow check valve not open Open tank valve and wait 10 seconds
until hose is pressurized before using
gun.
Clogged orice and/or lter Remove and clean with compressed air.
Clogged hose and/or fuel line Blow out or replace.
Combustor
turns
Red*
(insucient
fuel ow)
Leak in orice assembly Tighten orice in holder and check.
Wrong pressure Turn regulator up to 15 -30 PSIG.
Large Flame
(fuel ow)
*Leading edge of combustor will turn red under normal conditions. If more than 1” of combustor turns red trouble is indicated.
PARTS INDEX - INDIVIDUAL ITEMS
Dr. Shrink, Inc. (“The Seller”) warrants each RAPID SHRINK 100 shrink gun delivered, except as
expressly noted below, to be free from defects in material and workmanship under normal use
and service for 1 year after the date of delivery to the Buyer. Seller’s obligations under this
warranty are limited exclusively to those set forth below and are subject to the conditions also set
forth below.
This warranty shall not apply to any unit: (1) which shall have been repaired or altered outside
Seller’s factory in any way so as, in Seller’s judgment, to aect such unit’s reliability; (2) which has
been subject to misuse, negligence or accident; or (3) which has been operated or handled other
than in accordance with the printed instructions prepared by Seller and provided by Seller with
the unit.
THEWARRANTY GIVEN HEREIN IS EXCLUSIVE. SELLER DOES NOT WARRANT MERCHANTABILITY OR
FITNESS FOR ANY PARTICULAR PURPOSE OR MAKE ANY OTHER WARRANTY OR AGREEMENT
EXPRESS OR IMPLIED WITH RESPECT TO ANY NEW UNIT DELIVERED.
Seller’s obligations with respect to any unit delivered to Buyer are limited exclusively to repair or
replacement, if Seller’s examination shall disclose to its satisfaction that the unit is defective as
specied in the above warranty. Any defective unit shall be returned to Dr. Shrink, Inc., 315
Washington St., Manistee, MI 49660, postage or freight prepaid. Under such circumstances the
risk of loss and freight charges both to and from Seller’s plant be borne by the Buyer. Seller shall
bear the cost of repair or replacement and the risk of loss while the unit is in its possession. Seller
shall reship any such replacement or repaired unit to Buyer, prepaid.
The remedy provided herein is the exclusive remedy for the Buyer. Seller shall not be responsible
for incidental or consequential damages including, without limitation, claims for property
damage, lost prots, interruption of operations, or the like caused by any unit delivered to Buyer.
1
2
4
8
6
5
9
7
11 12
13
14
15
16
17
18
10
10 Combustor
11 Right Handle
12 Left Handle
13 Regulator
14 25’Propane Hose
15 Safety Glasses
16 Safety Gloves
17 Assembly Screws
18 Assembly Nuts
* Parts 2, 5, & 6
are one connected
unit/assembly
**Dr. Shrink, Inc. is an
authorized Rapid
Shrink 100 repair
center. If your heat
tool is in need of
repair, please call
[phone] to
speak with a heat tool
repair specialist.

315 Washington St.
Manistee, Michigan
49660-1855
[phone]
[phone]
[phone]
www.dr-shrink.com
[e-mail]
A PROUD MICHIGAN COMPANY
P:
P:
F:
R
S
100
YOUR COMPLETE OWNER’S MANUAL
FOR THE RAPID SHRINK 100 (RS-100) HEAT TOOL
OWNER’S
MANUAL