Draper FOUNDATION 303001 User manual

FORM: FDN_SONY_Inst21

WARNING
Improper installation and use of Foundation for LED Panels can result in serious injury or death. Primarily, injuries can occur when the Foundation for LED
Panels falls due to imprecise installation, mishandling of the Foundation for LED Panels during installation or installation on an insufficient wall or ceiling
structure. Please use extreme care.
1.
Please read the following installation guidelines thoroughly and follow them carefully. Failure to do so may cause product to fall or otherwise fail, and could
result in serious injury.
2. Installation and use of any video wall display should be conducted with approved clearances for operating and servicing the display along with adequate
ventilation for cooling. Consult your display manufacturer for operation, ventilation, and servicing conditions and requirements. Draper does not make
recommendations related to proper operation of any display nor will Draper accept liability for a display which fails due to improper installation, use, or
ventilation.
3. Installation and calibration of the Foundation for LED Panels should only be performed by an authorized, qualified, and experienced professional. In particular,
electrical work and wiring [indicated in diagram by dashed lines] must be completed only by a qualified professional electrician who has read this manual
completely and is familiar with the construction and operation of this equipment and the hazards involved.
4. Turn off power and any nearby equipment or cables carrying electricity before connecting switches, wires, controls, or electrical components.
5. Do not affix the unit to wall or ceilings that have inadequate strength to permanently hold the unit during use. It is the owner’s and installer’s responsibility to
confirm the wall to which the unit attaches is sufficient to permanently hold the weight and stress loads of the unit at all times. Draper, Inc., is not responsible
for improper installation, application, testing or workmanship related to the product at place of installation.
6. It is the installer’s responsibility to make sure appropriate fasteners are used for mounting.
7. All brackets and other hardware must be installed level. Foundation for LED Panels must be level and square.
8. Never leave the area while operating the Foundation for LED Panels during installation, maintenance, or normal operation, unless it is secure and safe.
9. Before testing or operation, carefully inspect the entire area and areas underneath to be sure no persons or objects are in the area.
10. During testing or operation, carefully watch the surrounding area for any potential safety concerns including nearby persons or objects.
11. After installation, the entire system should be carefully tested to ensure safe and normal operation.
Extreme care should be taken during testing to remain clear of moving parts to avoid possible injury.
12. Operation of Foundation for LED Panels should be performed only by authorized and qualified personnel, who have been trained in the safe and effective
operation of the Foundation for LED Panels & understand its safety features.
13. The safety features of the Foundation for LED Panels should never be disabled, bypassed or overridden.
The system should not be operated until all safety features are properly and completely installed, calibrated and tested.
14. Foundation for LED Panels may need to comply with local, state or district rules and regulations, in particular when installed in schools.
All applicable rules and regulations should be reviewed before installation and use.
15. Failure to precisely follow installation guidelines invalidates all warranties.
16. Custom products/installations may not be reflected in this manual.
Call Draper, Inc., if you have questions about the installation of custom products or any questions about your installation.
Before Beginning Installation
1. Look for any job site conditions that could interfere with installation or operation of the system.
2. Read carefully and be sure to understand all installation instructions and all related operations manuals. These instructions are intended to as a guide for the
installer and owner. They should be followed closely and combined with the expertise of experienced qualified installers. Draper, Inc., is not responsible for
improper installation, application, testing or workmanship related to the product at place of installation. Please retain all instructions for future use.
3. Open cartons lengthwise.
4. Locate and lay out all pieces.
5. Inspect all boxes to make sure you have received the proper Foundation for LED Panels and parts.
6. If you have any difficulties with installing, servicing or operating your Foundation for LED Panels, call your dealer or Draper, Inc., 765 987-7999.
Important Safety Information
Foundation
™for LED Panels

If you have any difficulties installing or servicing your
Foundation for LED Panels, call your dealer or Draper, Inc.
Draper, Inc. | 411 S. Pearl St. Spiceland, IN 47385
draperinc.com | 765.987.7999 | 800.238.7999
© 2021 All Rights Reserved | FORM: FDN_SONY_Inst21
Foundation
™for LED Panels
INSTRUCTIONS
ASSEMBLY & INSTALLATION
Overview
Section 1 - Personnel and Tools Required
PERSONNEL REQUIRED
LED Panels
Y-Axis
Adjustable
Vertical
Rails
Optional
Vented
Trim Frame
Z-Axis Adjustable
Horizontal Rail
HEX WRENCH
TAPEMEASURE
LASER LEVEL
POWER DRILL
3mm & 5mm
LEVEL
1
WORK GLOVES
RECOMMENDED
2

page 4 of 32
Foundation
™for LED Panels
Section 2 - Components
LED MOUNTING & ALIGNMENT
Differential
Screw
3mm Hex
Wrench
WALL
ADJUSTMENT
BRACKETS
HORIZONTAL RAIL
CONNECTORS
Top / Bottom
x4
SET SCREW
M6 - 1x8mm
Front
x1
RAIL CONNECTOR
x1
RAIL CONNECTOR
WASHER
.255" ID X .562" OD X .06"
x4
SPLIT LOCK
WASHER
.25" ID X .365" OD X .063"
x4
SCREW
M6 -1x10mm x4
VERTICAL RAIL
FASTENERS
SLIDE-IN NUT
M6-1.0
FLANGE HEAD SCREW
M6-1.0x12mm
VERTICAL RAILS
FOR
7 Panels
High
or
Less
HORIZONTAL RAILS
WALL
MOUNTING
BRACKETS
BUTTON-HEAD SCREW
M8-1.25x10mm Long
Flanged
+
VERTICAL RAIL
COUPLER
7 Panels High or More
x2
SONY Series C
LED Cabinet
Alignment
Tool
M10 Spring
Loaded
Mounting
Stud
TOP
VERTICAL
RAIL
Connects to
BOTTOM
VERTICAL
RAIL
with
Vertical
Rail
Coupler
FOR
6 Panels
High
or
Less
6
5
4
3
2
1
8
7
6
5
4
3
2
1
SONY Series C
LED Cabinets
(Not Included)

page 5 of 32
Foundation
™for LED Panels
Section 2 - Components Section 2 (continued) - Trim Frame Components
LEFT
BOTTOM
TRIM
SECTION
LEFT
TOP TRIM
SECTION
TOP CENTER TRIM SECTION
TOP RIGHT TRIM SECTIONTOP LEFT TRIM SECTION
RIGHT
BOTTOM
TRIM
SECTION
RIGHT
TOP TRIM
SECTION
BOTTOM CENTER TRIM SECTION
BOTTOM LEFT TRIM SECTION BOTTOM RIGHT TRIM SECTION
SIDE VERTICAL
MATING TRIM
ATTACHMENT
BRACKET
BLACK SOCKET
HEAD SCREW
M4-0.7x10mm
BOTTOM RIGHT
TRIM SUPPORT
BRACKET
BOTTOM CENTER
TRIM SUPPORT
BRACKET
BOTTOM LEFT
TRIM SUPPORT
BRACKET
TOP CENTER TRIM
ATTACHMENT
BRACKET
C002.1731SA
TOP RIGHT TRIM
ATTACHMENT
BRACKET
C002.1734SA
TOP LEFT TRIM
ATTACHMENT
BRACKET
C002.1735SA
SIDE TRIM
SUPPORT
BRACKET
C002.1732SA
SOCKET HEAD
SCREW
M4-0.7x10mm
SPLIT LOCK
WASHER M4

page 6 of 32
Foundation
™for LED Panels
Section 3 - Determining Horizontal Mounting Location
Section 3.1 - For LED arrays up to 6 panels high - 2 Horizontal Rails
The Foundation Wall Brackets must be securely anchored to the wall. If mounting to drywall/gypsum board wall, all mounting hardware (by others) must be
anchored to a vertical stud. If mounting to a brick or block wall, the brackets must be evenly spaced no more then 32”
(813mm) apart. In the drawings showing
in this manual, the bracket spacing is 24" unless specified otherwise.
The example below is for a 6 x 6 Array. Other standard 2 rail array sizes (4x4 & 5x5) are shown in the table at right.
1.
Mark the location of the Bottom Left Corner of the viewing area.
2. From the mark made in step 1, measure up 20 ⁄ " (531mm) and draw a level horizontal line the width of the LED display.
This is the top mounting hole location of the WALL MOUNTING BRACKET FOR THE BOTTOM HORIZONTAL RAIL (see Mounting Bracket Detail at right) .
3. From the mark made in step 1, measure up 79 ⁄" (2029mm) and draw a level horizontal line the width of the LED display.
This is the top mounting hole location of the WALL MOUNTING BRACKET FOR THE TOP HORIZONTAL RAIL
(see Mounting Bracket Detail at right) .
For 4x4 or 5x5 arrays, use the chart at right to determine the proper value for Dim A.
The fully assembled Horizontal Rails (see section 4) will be hung from them in Section 5.
Fig. 3.1
Overall
Height
81 7/8"
(2080mm)
Image
Height
80 13/16"
(2052mm)
20 7/8"
(531mm)
Overall Width with Trim: 144 3/4" (3676mm)
79 7/8"
(2029mm)
or
DIM A
from Chart Above
Image Width: 144 5/8" 3648mm)
BOTTOM RAIL
MOUNTING
HARDWARE
TOP RAIL
MOUNTING
HARDWARE
START HERE
LOCATE BOTTOM LEFT of Trim
LOCATE BOTTOM LEFT of Image Area
or
NOTE: If installing trim, you must allow 1
5
/16" (33mm) of clearance around the outside of the image area.
LOCATION of
BOTTOM RIGHT
LED Cabinet
LOCATION of
BOTTOM LEFT
LED Cabinet
6 x 6 Array Shown
Refer to chart above for
mounting dimension specific
to 4x4 and 5x5 Systems
PLEASE NOTE:
END OF HORIZONTAL RAIL to be
no more than 16"
(406mm) from the
CENTER of the OUTER Wall Brackets

page 7 of 32
Foundation
™for LED Panels
STANDARD ARRAY MOUNTING DIMENSIONS
DIM A FINAL VIEWING AREA
Array
Size
Vertical distance from Bottom Left of to Top
Rail Mounting Hardware
HEIGHT WIDTH
4x4 53"
(1345mm)
53 ⁄ "
(1368mm)
95
⁄
"
(2432mm)
5x5 66
⁄ "
(1687mm)
67 ⁄ "
(1710mm)
119 ⁄ "
(3040mm)
6x6 79
⁄
"
(2029mm)
80
⁄
"
(2052mm)
143 ⁄ "
(3648mm)
Overall
Height
81 7/8"
(2080mm)
Image
Height
80 13/16"
(2052mm)
20 7/8"
(531mm)
Overall Width with Trim: 144 3/4" (3676mm)
79 7/8"
(2029mm)
or
DIM A
from Chart Above
Image Width: 144 5/8" 3648mm)
BOTTOM RAIL
MOUNTING
HARDWARE
TOP RAIL
MOUNTING
HARDWARE
START HERE
LOCATE BOTTOM LEFT of Trim
LOCATE BOTTOM LEFT of Image Area
or
NOTE: If installing trim, you must allow 1 5/16" (33mm) of clearance around the outside of the image area.
LOCATION of
BOTTOM RIGHT
LED Cabinet
LOCATION of
BOTTOM LEFT
LED Cabinet
6 x 6 Array Shown
Refer to chart above for
mounting dimension specific
to 4x4 and 5x5 Systems
9/16"
( Ø 14mm)
Ø 13/16"
( Ø 20mm)
Ø 5/16"
( Ø 7mm)
LASER LINE
Mounting
Hardware
MOUNTING
BRACKET
DETAIL

page 8 of 32
Foundation
™for LED Panels
Section 3.2 - For LED arrays 7 panels or higher - 3 Horizontal Rails
The Foundation Wall Brackets must be securely anchored to the wall. If mounting to drywall/gypsum board wall, all mounting hardware (by others) must be
anchored to a vertical stud. If mounting to a brick or block wall, the brackets must be evenly spaced no more then 32”
(813mm) apart.
The example below is for a 8 x 8 Array. Dimensions for other standard 3 rail array sizes (10x10 and 12x2) are shown in the table at right.
1.
Mark the location of the Bottom Left Corner of the viewing area.
2. From the mark made in step 1, measure up 20 ⁄" (350mm) and draw a level horizontal line the width of the LED display.
This is the top mounting hole location of the WALL MOUNTING BRACKET FOR THE BOTTOM HORIZONTAL RAIL (see Mounting Bracket Detail at right) .
3. From the mark made in step 1, measure up 53" (1345mm) and draw a level horizontal line the width of the LED display.
For 10x10 or 12x12 arrays, use the chart at right to determine the proper value for Dim A.
4. From the mark made in step 1, measure up 106 ⁄" (2713mm) and draw a level horizontal line the width of the LED display.
This is the top mounting hole location of the WALL MOUNTING BRACKET FOR THE TOP HORIZONTAL RAIL
(see Mounting Bracket Detail at right) .
For 10x10 or 12x12 arrays, use the chart at right to determine the proper value for Dim B.
The fully assembled Horizontal Rails (see section 4) will be hung from them in Section 5.
START HERE
LOCATE BOTTOM LEFT of Trim
LOCATE BOTTOM LEFT of Image Area
or NOTE: If installing trim, you must allow 1 5/16
" (33mm) of clearance around the outside of the image area.
Overall
Height
108 13/16"
(2764mm)
Image
Height
107 7/8"
(2736mm)
106 13/16"
(2713mm)
or
DIM B
from Chart Above
TOP RAIL
MOUNTING
HARDWARE
20 7/8"
(531mm)
Overall Width with Trim: 192 5/8" (4892mm)
53"
(1345mm)
or
DIM A
from Chart Above
Image Width: 191 1/2" 4864mm)
BOTTOM
RAIL
MOUNTING
HARDWARE
MIDDLE RAIL
MOUNTING
HARDWARE
8 x 8 Array Shown
Refer to chart above for
mounting dimension specific
to 10x10 and 12x12 Systems
LOCATION of
BOTTOM RIGHT
LED Cabinet
LOCATION of
BOTTOM LEFT
LED Cabinet
PLEASE NOTE:
END OF HORIZONTAL RAIL to be
no more than 16"
(406mm) from the
CENTER of the OUTER Wall Brackets

page 9 of 32
Foundation
™for LED Panels
START HERE
LOCATE BOTTOM LEFT of Trim
LOCATE BOTTOM LEFT of Image Area
or NOTE: If installing trim, you must allow 1 5/16" (33mm) of clearance around the outside of the image area.
Overall
Height
108 13/16"
(2764mm)
Image
Height
107 7/8"
(2736mm)
106 13/16"
(2713mm)
or
DIM B
from Chart Above
TOP RAIL
MOUNTING
HARDWARE
20 7/8"
(531mm)
Overall Width with Trim: 192 5/8" (4892mm)
53"
(1345mm)
or
DIM A
from Chart Above
Image Width: 191 1/2" 4864mm)
BOTTOM
RAIL
MOUNTING
HARDWARE
MIDDLE RAIL
MOUNTING
HARDWARE
8 x 8 Array Shown
Refer to chart above for
mounting dimension specific
to 10x10 and 12x12 Systems
LOCATION of
BOTTOM RIGHT
LED Cabinet
LOCATION of
BOTTOM LEFT
LED Cabinet
9/16"
( Ø 14mm)
Ø 13/16"
( Ø 20mm)
Ø 5/16"
( Ø 7mm)
LASER LINE
Mounting
Hardware
MOUNTING
BRACKET
DETAIL
STANDARD ARRAY MOUNTING DIMENSIONS
DIMA DIM B FINAL VIEWING AREA
Array
Size
Vertical distance from Bottom Left of Array
to Middle Rail Mounting Hardware
Vertical distance from Bottom Left of Array
to Top Rail Mounting Hardware
HEIGHT WIDTH
8x8 53"
(1345mm)
106 ⁄ "
(2713mm)
107 ¾ "
(2736mm)
191 ½ "
(4864mm)
10x10 66
⁄ "
(1687mm)
134 ¾ "
(3397mm)
134 ⁄ "
(3420mm)
239 ⁄ "
(6080mm)
12x12 79
⁄ "
(2029mm)
160 ⁄ "
(4081mm)
161 ⁄ "
(4104mm)
287 ⁄ "
(7296mm)

page 10 of 32
Foundation
™for LED Panels
STUD
GYPSUM
BOARD
WALL
Mounting
Hardware
(by others)
STUD
PLYWOOD BACKER
GYPSUM
BOARD
WALL
Mounting
Hardware
(by others)
OR
Fig. 3.3
Section 3.2 - Marking Vertical Mounting locations
STUDS
SHOWN
Fig. 3.2-1
Section 3.2.1 - WOOD/METAL STUD INSTALLATION
1. Locate the wall studs and mark their location at the intersection of the
lines drawn in Section 3.1.
MAX. WALL
BRACKET SPACING:
24"
(610mm) to 32" (813mm)
Fig. 3.2-2
Please Note: It is the responsibility of the installer to select mounting
hardware appropriate for the mounting surface
9/16"
( Ø 14mm)
Ø 13/16"
( Ø 20mm)
Ø 5/16"
( Ø 7mm)
LASER LINE
Mounting
Hardware
MOUNTING
BRACKET
DETAIL
Section 3.3 - Attaching Mounting Hardware (by Others) to Wall
1.
Loosely attach the wall mounting hardware (provided by others) to the wall at the outer four corners of the grid created in Sections 3.1 & Section 3.2.
Ensure the head of the hardware is at least ½ ” (12mm) off the surface of the wall.
The assembled Horizontal Rails will be hung from these in SECTION 5 - Hanging Horizontal Rails.
Section 3.2.2 - CONCRETE, BLOCK OR BRICK INSTALLATION
1. Draw vertical lines spaced 24" (609mm) to 32" (813mm) apart.
MIN: .25" x 1.75" L
HEX HEAD LAG SCREW
BY OTHERS
MOUNTING LAG SCREW
BY OTHERS MIN: .25" x 1.75" L
Must attach to studs or
1/2" Plywood Backer

page 11 of 32
Foundation
™for LED Panels
Please Note:
Only the TOP and BOTTOM rail connectors
will be used to assemble the rails.
Front Rail Connector will be installed
later in Section 9.
Section 4 - Assembling Horizontal Rails
The horizontal rails must be assembled prior to being secured to the wall.
A complete Horizontal Rail consists of Wall Mounting Brackets engaged in both
TOP and BOTTOM Channels of extruded rail sections
(see MOUNTING BRACKET DETAIL at right) .
Horizontal rail sections are extended in length using 3 Horizontal Rail Connectors per splice.
SLIDES INTO
BOTTOM
CHANNEL
OF
HORIZONTAL RAIL
SLIDES INTO
TOP
CHANNEL
OF
HORIZONTAL RAIL
MOUNTING
BRACKET
DETAIL
HORIZONTAL RAIL
SECTION PROFILE
BOTTOM
CHANNEL
TOP
CHANNEL
FRONT
CHANNEL
See Section 9
To assemble the Horizontal rails:
See chart above for the suggested number of wall brackets required per rail and splice locations.
Note: For Array sizes that require more
than one Rail Splice, you MUST locate
the wall mounting brackets on the center
rail section prior to securing splices.
SPLICE SPLICE
Horizontal Rails for Standard Array Sizes
10
9
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
4
3
2
1
6
5
4
3
2
1
10
9
8
7
6
5
4
3
2
1
12
11
5
4
3
2
1
PANELS
WIDE
PANELS
WIDE
PANELS
WIDE
PANELS
WIDE
PANELS
WIDE
PANELS
WIDE
STANDARD ARRAY SIZES - SUGGESTED BRACKETS REQUIRED & SPLICE LOCATIONS
LED MOUNTING & ALIGNMENT
Differential
Screw
3mm Hex
Wrench
WALL
ADJUSTMENT
BRACKETS
HORIZONTAL RAIL
CONNECTORS
Top / Bottom
x4
SET SCREW
M6 - 1x8mm
Front
x1
L
RAIL CONNECTOR
x1
RAIL CONNECTOR
WASHER
.255" ID X .562" OD X .06"
x4
SPLIT LOCK
WASHER
.25" ID X .365" OD X .063"
x4
SCREW
M6 -1x10mm x4
VERTICAL RAIL
FASTENERS
SLIDE-IN NUT
M6-1.0
FLANGE HEAD SCREW
M6-1.0x8mm
VERTICAL RAILS
VERTICAL
RAIL
RIGHT SIDE
VERTICAL
RAIL
CENTER
VERTICAL
RAIL
LEFT SIDE
HORIZONTAL RAILS
WALL
MOUNTING
BRACKETS
BUTTON-HEAD SCREW
M8-1.25x10mm Long
Flanged
+
VERTICAL RAIL
COUPLER
4 High or More
x2
PLUM
ALIGNMENT
PIN
SAMSUNG IER
SAMSUNG IFR
LED Cabinet
Alignment
Tool
M6 LED
Mounting
Stud
C021.044
SAMSUNG IER
or
SAMSUNG IFR
LED Cabinets
(Not Included)
HEX WRENCH
5mm
Slide Rail Section B
over slats in wall bracket
Slide Rail Connectors
into slots in Section A
A B
4-1
Slide Rail Section B
over Rail Connectors
BA
4-2
Tighten all rail connector
screws with 5mm hex wrench
4-3

page 12 of 32
Foundation
™for LED Panels
Section 5 - Hanging Horizontal Rails
WALL
Leave All Brackets loose for now.
Brackets will be adjusted to fit site conditions in Section 6.
STUD
WALL
Section 5.1 - For LED arrays up to 6 panels high - 2 Horizontal Rails
1. Using the top keyhole slots of the two outer wall mounting brackets,
hang the bottom horizontal rail on the pre-installed mounting hardware
(see Section 3, Step 5) .
1
2
3
Fig. 5-1
1
2
3
Fig. 5-2
1
2
3
Fig. 5-3
2. Using the top keyhole slots of the outer wall mounting brackets,
hang the top horizontal rails on the pre-installed mounting hardware.
3. Leave all brackets loose for now. Brackets will be adjusted to fit site
conditions in Section 6 - Adjusting and Aligning Horizontal Rails.

page 13 of 32
Foundation
™for LED Panels
Section 5.2 - For LED arrays 7 panels or higher - 3 Horizontal Rails
1. Using the top keyhole slots of the outer wall mounting brackets, hang the BOTTOM
horizontal rail on the pre-installed mounting hardware
(see Section, 3 Step 5) .
2. Using the top keyhole slots of the outer wall mounting brackets, hang the MIDDLE
horizontal rail on the pre-installed mounting hardware.
3. Using the top keyhole slots of the outer wall mounting brackets, hang the TOP
horizontal rail on the pre-installed mounting hardware.
4. Leave all brackets loose for now. Brackets will be adjusted to fit site conditions in
Section 6 - Adjusting and Aligning Horizontal Rails.
4
21
3
STUD
WALL
WALL
Leave All Brackets loose for now.
Brackets will be adjusted to fit site conditions in Section 6.

page 14 of 32
Foundation
™for LED Panels
Section 6 - Adjusting and Aligning Horizontal Rails
1. Push the wall brackets against the wall where they will be mounted. Depending on the flatness of the wall some brackets may not touch the wall (see Fig. 6-1) .
2. For any wall brackets not touching the wall (see BLUE CIRCLES ABOVE) use a 5mm Hex Wrench to loosen the four (4) locking screws
on the top and bottom of each bracket
(See Fig. 6-2) .
3. Using a 3mm Hex Wrench, turn the two (2) adjustment set screws on each wall mounting bracket.
Adjust the wall bracket back until it touches the wall
(see Fig. 6-3) .
PLEASE NOTE: Take care not to adjust too far and force any wall brackets off the wall that were touching it.
A level or straight edge can also be laid across the front face of the horizontal rail
between 3 or more wall brackets to ensure the rail is straight.
4. Leaving the wall brackets free floating, shine a laser line parallel to the desired viewing surface
of the LED wall and close to the horizontal rails.
5. Using a tape measure check the distance from the laser line to the horizontal rail at each wall bracket,
and adjust any wall brackets until all measurements match.
6. Once all brackets are in contact with the wall, and the horizontal rails are perfectly straight, tighten all adjustment screws.
Tighten
Adjustment
Screws
Tighten
Adjustment
Screws
TOP VIEW - CONCAVE WALL
Laser Line
I
N
C
O
N
T
A
C
T
W
I
T
H
W
A
L
L
M
U
S
T
A
D
J
U
S
T
T
O
W
A
L
L
M
U
S
T
A
D
J
U
S
T
T
O
W
A
L
L
M
U
S
T
A
D
J
U
S
T
T
O
W
A
L
L
M
U
S
T
A
D
J
U
S
T
T
O
W
A
L
L
M
U
S
T
A
D
J
U
S
T
T
O
W
A
L
L
M
U
S
T
A
D
J
U
S
T
T
O
W
A
L
L
M
U
S
T
A
D
J
U
S
T
T
O
W
A
L
L
I
N
C
O
N
T
A
C
T
W
I
T
H
W
A
L
L
M
U
S
T
A
D
J
U
S
T
T
O
W
A
L
L
Laser Line
TOP VIEW - CONVEX WALL
M
U
S
T
A
D
J
U
S
T
T
O
W
A
L
L
M
U
S
T
A
D
J
U
S
T
T
O
W
A
L
L
M
U
S
T
A
D
J
U
S
T
T
O
W
A
L
L
I
N
C
O
N
T
A
C
T
W
I
T
H
W
A
L
L
M
U
S
T
A
D
J
U
S
T
T
O
W
A
L
L
M
U
S
T
A
D
J
U
S
T
T
O
W
A
L
L
M
U
S
T
A
D
J
U
S
T
T
O
W
A
L
L
M
U
S
T
A
D
J
U
S
T
T
O
W
A
L
L
Fig. 6-1
Loosen
Adjustment
Screws
Loosen
Adjustment
Screws
Fig. 6-2
3mm Hex
Wrench
BRACKET MOVES
TOWARDS WALL
Fig. 6-3
Fig. 6-4

page 15 of 32
Foundation
™for LED Panels
Section 7 - Securing Inner Wall Brackets
1. Secure each bracket to the wall with the appropriate mounting hardware.
2. Check the distance from the laser line at each wall bracket to ensure nothing moved while fastening to the wall. Adjust if necessary.
3. Carefully tighten all four (4) locking screws on the top and bottom of each wall mounting bracket.
Tighten
Adjustment
Screws
Tighten
Adjustment
Screws
Section 8 - Attaching Wall Adjuster Brackets to Vertical Rails
Section 8.1 - For LED arrays up to 6 panels high - 2 Horizontal Rails
1. Attach the Differential Screw to the Wall Adjustment Bracket.
2. Attach two (2) Wall Adjuster Brackets to the back side using a 3mm hex wrench.
WORK GLOVES
RECOMMENDED
1
WALL ADJUSTER
BRACKET
ASSEMBLY
Attach Differential Screw
using 3mm Hex Wrench 3mm Hex
Wrench
engaged with
differential
screw
Back TOP
2

page 16 of 32
Foundation
™for LED Panels
Section 8.2 - Vertical Rail Assembly - For LED arrays 7 panels or higher - 3 Horizontal Rails
Section 8.2.1 - Lower Section of Vertical Rail Assembly
1. Insert Vertical Connector into TOP of the Lower Vertical Rail section and secure with provided hardware (3mm Hex Wrench) .
2. Turn the Lower Vertical Rail section over.
3.
Attach two (2) Wall Adjuster Brackets
to the back side using a 3mm hex wrench.
Section 8.2.2 - Upper Section of Vertical Rail Assembly
1. Attach one (1) Wall Adjuster Bracket to the back side using a 3mm hex wrench.
WORK GLOVES
RECOMMENDED
TURN OVER
Front
TOP
2
Back
TOP
3
Front
TOP
1
VERTICAL
CONNECTOR
A
TURN OVER
Front
TOP
2
Back
TOP
3
Front
TOP
1
3mm Hex
Wrench
engaged with
differential
screw

page 17 of 32
Foundation
™for LED Panels
Section 9 - Inserting Front Rail Connector and Vertical Rail Fasteners
Section 9.1 - For LED arrays up to 6 panels high - 2 Horizontal Rails
1. Insert horizontal rail connector and vertical rail fasteners into the top and bottom horizontal rails.
Eventual location of Vertical Rails shown
4x4 5 Vertical Rails
5
4321 54321
44 54
321
44 54
321
5x5
6 Vertical Rails
Splice
654321 654321
6
54321
Rail
Connector
(FRONT)
6
54321
Rail
Connector
(FRONT)
Eventual location of Vertical Rails shown
6x6
7 Vertical Rails
Splice
7654321 7654321
65 74321
Rail
Connector
(FRONT)
65 74321
Rail
Connector
(FRONT)
Eventual location of Vertical Rails shown

page 18 of 32
Foundation
™for LED Panels
SpliceSplice
12x12 13 Vertical Rails
131211
10
9
8
7
65
4
321 131211109
8
7
65
4321
65 10 91211 874
Rail
Connector
(FRONT)
Rail
Connector
(FRONT)
321
Rail
Connector
(FRONT)
13
65 10 91211 874
Rail
Connector
(FRONT)
Rail
Connector
(FRONT)
321
Rail
Connector
(FRONT)
13
65 10 91211 874
Rail
Connector
(FRONT)
Rail
Connector
(FRONT)
321
Rail
Connector
(FRONT)
13
Eventual location of Vertical Rails shown
10x10 11 Vertical Rails
SpliceSplice
11109
8
7
65
4321 11109
8
7
65
4321
65 10 911 874321
Rail
Connector
(FRONT)
Rail
Connector
(FRONT)
65 10 911 874321
Rail
Connector
(FRONT)
Rail
Connector
(FRONT)
65 10 911 874321
Rail
Connector
(FRONT)
Rail
Connector
(FRONT)
Eventual location of Vertical Rails shown
8x8
9 Vertical Rails
Splice Splice
987654321 987654321
65 9874321
Rail
Connector
(FRONT)
Rail
Connector
(FRONT)
65 9874321
Rail
Connector
(FRONT)
Rail
Connector
(FRONT)
65 9874321
Rail
Connector
(FRONT)
Rail
Connector
(FRONT)
Eventual location of Vertical Rails shown
Section 9.2 - For LED arrays 7 panels or higher - 3 Horizontal Rails
1. Insert horizontal rail connector and vertical rail fasteners into the top, middle and bottom horizontal rails.

page 19 of 32
Foundation
™for LED Panels
Section 10 - Attaching Vertical Rails
Section 10.1 - For LED arrays up to 6 panels high - 2 Horizontal Rails
1. Hang the Vertical Rails on the top horizontal rail and space evenly.
2. Using a 5mm hex wrench, slide the fastener nuts (from Section 9) into position and attach using the supplied M6x12 hardware.
WORK GLOVES
RECOMMENDED
VERTICAL
RAIL
HORIZONTAL
RAIL
VERTICAL
RAIL
HORIZONTAL
RAIL
Fig. 10-1A Fig. 10-1B
VERTICAL
RAIL
HORIZONTAL
RAIL
VERTICAL
RAIL
SLIDE IN
FASTENER
Fig. 10-2A Fig. 10-2B
LED MOUNTING & ALIGNMENT
Differential
Screw
3mm Hex
Wrench
WALL
ADJUSTMENT
BRACKETS
HORIZONTAL RAIL
CONNECTORS
Top / Bottom
x4
SET SCREW
M6 - 1x8mm
Front
x1
L
RAIL CONNECTOR
x1
RAIL CONNECTOR
WASHER
.255" ID X .562" OD X .06"
x4
SPLIT LOCK
WASHER
.25" ID X .365" OD X .063"
x4
SCREW
M6 -1x10mm x4
VERTICAL RAIL
FASTENERS
SLIDE-IN NUT
M6-1.0
FLANGE HEAD SCREW
M6-1.0x8mm
VERTICAL RAILS
VERTICAL
RAIL
RIGHT SIDE
VERTICAL
RAIL
CENTER
VERTICAL
RAIL
LEFT SIDE
HORIZONTAL RAILS
WALL
MOUNTING
BRACKETS
BUTTON-HEAD SCREW
M8-1.25x10mm Long
Flanged
+
VERTICAL RAIL
COUPLER
4 High or More
x2
PLUM
ALIGNMENT
PIN
SAMSUNG IER
SAMSUNG IFR
LED Cabinet
Alignment
Tool
M6 LED
Mounting
Stud
C021.044
SAMSUNG IER
or
SAMSUNG IFR
LED Cabinets
(Not Included)

page 20 of 32
Foundation
™for LED Panels
Section 10.2 - For LED arrays 7 panels or higher - 3 Horizontal Rails
Section 10.2.1 - Attaching Bottom Vertical Sections
1. Lift each Vertical Rail and position it on the middle rail.
2. Let the Vertical Rail hanger rest on the horizontal rail.
3. Slide the fastener nut from Section 8 into position
and loosely attach with the provided hardware.
4. Work from left to right until all bottom Vertical Rails
are attached.
Section 10.2.2 - Attaching Top Vertical Sections
1. Lift each Top Section of Vertical Rail and slide it onto the connector on the bottom section.
2. Let the Vertical Rail hanger rest on the top horizontal rail and secure it loosely with provided hardware..
3. Slide the fastener nut from Section 8 into position on the bottom rail and loosely attach with the provided hardware.
4. Work from left to right until all top Vertical Rails are attached.
21
2
SCREW
M8-1.25x10mm
Long Flanged
Button Head