Draytek Vigor2110 Series User manual

i
Vigor2110 Series
Broadband Firewall Router
Quick Start Guide
Version: 1.0
Date: 2008/09/01

i
Copyright Information
Copyright
Declarations
Copyright 2008 All rights reserved. This publication contains information that is
protected by copyright. No part may be reproduced, transmitted, transcribed,
stored in a retrieval system, or translated into any language without written
permission from the copyright holders.
Trademarks
The following trademarks are used in this document:
zMicrosoft is a registered trademark of Microsoft Corp.
zWindows, Windows 95, 98, Me, NT, 2000, XP, Vista and Explorer are
trademarks of Microsoft Corp.
zApple and Mac OS are registered trademarks of Apple Inc.
zOther products may be trademarks or registered trademarks of their
respective manufacturers.
Safety Instructions and Approval
Safety
Instructions
zRead the installation guide thoroughly before you set up the router.
zThe router is a complicated electronic unit that may be repaired only be
authorized and qualified personnel. Do not try to open or repair the router
yourself.
zDo not place the router in a damp or humid place, e.g. a bathroom.
zDo not stack the routers.
zThe router should be used in a sheltered area, within a temperature range
of +5 to +40 Celsius.
zDo not expose the router to direct sunlight or other heat sources. The
housing and electronic components may be damaged by direct sunlight or
heat sources.
zDo not deploy the cable for LAN connection outdoor to prevent electronic
shock hazards.
zKeep the package out of reach of children.
zWhen you want to dispose of the router, please follow local regulations on
conservation of the environment.
Warranty
We warrant to the original end user (purchaser) that the router will be free from
any defects in workmanship or materials for a period of two (2) years from the
date of purchase from the dealer. Please keep your purchase receipt in a safe
place as it serves as proof of date of purchase. During the warranty period, and
upon proof of purchase, should the product have indications of failure due to
faulty workmanship and/or materials, we will, at our discretion, repair or replace
the defective products or components, without charge for either parts or labor, to
whatever extent we deem necessary tore-store the product to proper operating
condition. Any replacement will consist of a new or re-manufactured
functionally equivalent product of equal value, and will be offered solely at our
discretion. This warranty will not apply if the product is modified, misused,
tampered with, damaged by an act of God, or subjected to abnormal working
conditions. The warranty does not cover the bundled or licensed software of
other vendors. Defects which do not significantly affect the usability of the
product will not be covered by the warranty. We reserve the right to revise the
manual and online documentation and to make changes from time to time in the
contents hereof without obligation to notify any person of such revision or
changes.
Be a Registered
Owner Web registration is preferred. You can register your Vigor router via
http://www.draytek.com.
Firmware & Tools
Updates Due to the continuous evolution of DrayTek technology, all routers will be
regularly upgraded. Please consult the DrayTek web site for more information on
newest firmware, tools and documents.
http://www.draytek.com

ii
European Community Declarations
Manufacturer: DrayTek Corp.
Address: No. 26, Fu Shing Road, HuKou County, HsinChu Industrial Park, Hsin-Chu, Taiwan 303
Product: Vigor2110 Series Router
DrayTek Corp. declares that Vigor2110 Series of routers are in compliance with the following essential
requirements and other relevant provisions of R&TTE Directive 1999/5/EEC.
The product conforms to the requirements of Electro-Magnetic Compatibility (EMC) Directive
2004/108/EC by complying with the requirements set forth in EN55022/Class B and EN55024/Class B.
The product conforms to the requirements of Low Voltage (LVD) Directive 2006/95/EC by complying
with the requirements set forth in EN60950-1.
Regulatory Information
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the use is encouraged to try to correct the interference
by one of the following measures:
zReorient or relocate the receiving antenna.
zIncrease the separation between the equipment and receiver.
zConnect the equipment into an outlet on a circuit different form that to which the receiver is
connected.
zConsult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device may accept any interference received, including interference that may cause undesired
operation.
Please visit http://www.draytek.com/about_us/R_TTE_Certification.php.
This product is designed for POTS and 2.4GHz WLAN network throughout the EC region and Switzerland
with restrictions in France. Please see the user manual for the applicable networks on your product.

iii
T
Ta ab bl le e o of f C Co on nt te en nt ts s
1. Introduction........................................................................................................... 1
1.1 Panel Explanation ...................................................................................................................... 2
1.1.1 For Vigor2110 ............................................................................................................... 2
1.1.2 For Vigor2110n ............................................................................................................. 4
1.1.3 For Vigor2110Vn...........................................................................................................6
1.2 Package Content........................................................................................................................ 8
2. Installing Your Router........................................................................................... 9
2.1 Hardware Installation.................................................................................................................. 9
Stand Installation.................................................................................................................. 10
2.2 Printer Installation......................................................................................................................11
3. Configuring Web Pages ..................................................................................... 17
3.1 Accessing Web Page ............................................................................................................... 17
3.2 Basic Configuration.................................................................................................................. 18
3.3 Wireless Configuration............................................................................................................. 23
3.3.1 Basic Wireless LAN Concept...................................................................................... 23
3.3.2 General Setup.............................................................................................................23
3.3.3 Security Settings.........................................................................................................25
4. Trouble Shooting................................................................................................ 27
4.1 Checking If the Hardware Status Is OK or Not......................................................................... 27
4.2 Checking If the Network Connection Settings on Your Computer Is OK or Not ...................... 28
4.3 Pinging the Router from Your Computer.................................................................................. 30
4.4 Checking If the ISP Settings are OK or Not............................................................................. 31
4.5 Backing to Factory Default Setting If Necessary...................................................................... 33
4.6 Contacting Your Dealer ............................................................................................................ 34

1
1
1. . I In nt tr ro od du uc ct ti io on n
The Vigor2110 series features advanced bandwidth control mechanism such as IP-layer
QoS, NAT Session Limitation, Bandwidth Borrowed, etc., to allow easy, flexible, reliable
access control and bandwidth management.
The SPI (Stateful Packet Inspection) firewall uses object-based design to make settings of
firewall policies easy. The CSM (Content Security Management) feature allows more
precise and efficient access control for URL/Web Content Filtering, IM (Instant
Messenger) and P2P (Peer to Peer) applications.
Vigor2110 supports up to 2 VPN tunnels using advanced protocols such as
IPSec/PPTP/L2TP/L2TP over IPSec with AES/DES/3DES for encryption and
MD5/SHA-1 for authentication.
Vigor2110 ‘n’ models comply with 802.11n Draft-n standards. They support
WEP/WPA/WPA2 encryption and MAC Address Control, Wireless LAN Isolation. The
Wireless Rate Control function can adjust the data rate of each wireless station (client).
Vigor2110 ‘V’ models provide two analogue phone connectors and one line port. It
supports multiple SIP registrars with high flexible configuration and call handing options.
In addition, Vigor2110 series supports USB interface for connecting USB printer to share
printer or USB storage device for sharing files. Vigor2110 series provides two-level
management to simplify the configuration of network connection. The user mode allows
user accessing into WEB interface via simple configuration. However, if users want to
have advanced configurations, they can access into WEB interface through admin mode.

2
1
1. .1 1 P Pa an ne el l E Ex xp pl la an na at ti io on n
1
1. .1 1. .1 1 F Fo or r V Vi ig go or r2 21 11 10 0
LED Status Explanation
Blinking The router is powered on and running
normally.
ACT
(Activity) Off The router is powered off.
CSM On The profile(s) of CSM (Content
Security Management) for IM/P2P,
URL/Web Content Filter application
can be enabled from Firewall
>>General Setup. (Such profile must
be established under CSM menu).
On The WAN port is connected.WAN Blinking It will blink while transmitting data.
On The port is connected.
Off The port is disconnected.
LAN 1/2/3/4
Blinking The data is transmitting.
On A USB device is connected and active.USB Blinking The data is transmitting.
VPN On The VPN tunnel is active.
QoS On The QoS function is active.
On The DoS/DDoS function is active.DoS Blinking It will blink while detecting an attack.
WCF On The profile(s) of CSM (Content
Security Management) for Web
Content Filter application can be
enabled from Firewall >>General
Setup. (Such profile must be
established under CSM menu)
Interface Description
WAN Connector for accessing the Internet.
LAN (1-4) Connectors for local networked devices.
USB Connector for USB storage device (Pen
Driver/Mobile HD) or printer.

3
Interface Description
Factory Reset Restore the default settings. Usage: Turn on the router (ACT LED is blinking). Press
the hole and keep for more than 5 seconds. When you see the ACT LED begins to
blink rapidly than usual, release the button. Then the router will restart with the
factory default configuration.
PWR Connector for a power adapter.
ON/OFF Power Switch.

4
1
1. .1 1. .2 2 F Fo or r V Vi ig go or r2 21 11 10 0n n
LED Status Explanation
Blinking The router is powered on and running
normally.
ACT
(Activity) Off The router is powered off.
On Wireless access point is ready.WLAN Blinking It will blink while wireless traffic goes
through.
On The WAN port is connected.WAN Blinking It will blink while transmitting data.
On The port is connected.
Off The port is disconnected.
LAN 1/2/3/4
Blinking The data is transmitting.
On A USB device is connected and active.USB Blinking The data is transmitting.
VPN On The VPN tunnel is active.
QoS On The QoS function is active.
On The DoS/DDoS function is active.DoS Blinking It will blink while detecting an attack.
On The WPS is on.
Off The WPS is off.
WPS
Blinking Waiting for wireless client sending
requests for connection about two
minutes.
On Press this button for 2 seconds to wait
for client device making network
connection through WPS. When the
LED lights up, the WPS connection
will be on.
Off The WPS is off.
WPS Button
Blinking Waiting for wireless client sending
requests for connection about two
minutes.
Interface Description
WLAN Press the button once to enable (WLAN LED on) or
disable (WLAN LED off) wireless connection.
WAN Connector for accessing the Internet.
LAN (1-4) Connectors for local networked devices.
USB Connector for USB storage (Pen Driver /Mobile
HD) or printer.

5
Interface Description
Factory Reset Restore the default settings. Usage: Turn on the router (ACT LED is blinking). Press
the hole and keep for more than 5 seconds. When you see the ACT LED begins to
blink rapidly than usual, release the button. Then the router will restart with the
factory default configuration.
PWR Connector for a power adapter.
ON/OFF Power Switch.

6
1
1. .1 1. .3 3 F Fo or r V Vi ig go or r2 21 11 10 0V Vn n
LED Status Explanation
Blinking The router is powered on and running
normally.
ACT
(Activity) Off The router is powered off.
On Wireless access point is ready.WLAN Blinking It will blink while wireless traffic goes
through.
On The WAN port is connected.WAN Blinking It will blink while transmitting data.
On The port is connected.
Off The port is disconnected.
LAN 1/2/3/4
Blinking The data is transmitting.
On A USB device is connected and active.USB Blinking The data is transmitting.
On The phone connected to this port is
off-hook.
Off The phone connected to this port is
on-hook.
Phone1/
Phone2
Blinking A phone call comes.
On A PSTN phone call comes (in and out).
However, when the phone call is
disconnected, the LED will be off
about six seconds later.
Line
Off There is no PSTN phone call.
On The WPS is on.
Off The WPS is off.
WPS
Blinking Waiting for wireless client sending
requests for connection about two
minutes.
On Press this button for 2 seconds to wait
for client device making network
connection through WPS. When the
LED lights up, the WPS connection
will be on.
Off The WPS connection is off.
WPS Button
Blinking Waiting for wireless client sending
requests for connection about two
minutes.
Interface Description
WLAN Press the button once to enable (WLAN LED on) or
disable (WLAN LED off) wireless connection.
WAN Connector for accessing the Internet.
LAN (1-4) Connectors for local networked devices.
USB Connector for USB storage (Pen Driver/Mobile
HD) or printer.

7
Interface Description
Line Connector for PSTN life line.
Phone2/Phone1 Connector of analog phone for VoIP communication.
Factory Reset Restore the default settings. Usage: Turn on the router (ACT LED is blinking). Press
the hole and keep for more than 5 seconds. When you see the ACT LED begins to
blink rapidly than usual, release the button. Then the router will restart with the
factory default configuration.
PWR Connector for a power adapter.
ON/OFF Power Switch.

8
1
1. .2 2 P Pa ac ck ka ag ge e C Co on nt te en nt t
nQuick Start Guide oCD
pRJ-45 Cable (Ethernet) qAntenna (n models)
rStand
sThe type of the power adapter depends on the country that the router will be installed.
* The maximum power consumption is 17-23 Watt.
UK-type Power Adapter EU-type Power Adapter
USA/Taiwan-type Power Adapter AU/NZ-type Power Adapter

9
2
2. . I In ns st ta al ll li in ng g Y Yo ou ur r R Ro ou ut te er r
This section will guide you to install the router through hardware connection and
configure the router’s settings through web browser.
2
2. .1 1 H Ha ar rd dw wa ar re e I In ns st ta al ll la at ti io on n
Before starting to configure the router, you have to connect your devices correctly.
1. Connect Line port to land line jack with a RJ-11 cable (Vn model).
2. Connect this device to a modem with an Ethernet cable.
3. Connect one port of 4-port switch to your computer with a RJ-45 cable. This device
allows you to connect 4 PCs directly.
4. Connect Phone port to a conventional analog telephone.
5. Connect detachable antennas to the router for Vigor2110 series (n model).
6. Connect one end of the power cord to the power port of this device. Connect the
other end to the wall outlet of electricity.
7. Power on the router.
8. Check the ACT and WAN, LAN LEDs to assure network connections.
(For the detailed information of LED status, please refer to section 1.1.)
Caution:
1. Each of the Phone ports can be connected to an analog phone only. Do not connect the
phone ports to the land line jack. Such connection might damage your router.
2. When the power is shutdown, VoIP phone will be disconnected. However, a phone set
connected to Phone 2 port can be used as the traditional telephone for the line will be
guided to land line jack via the router (loop through).

10
S
St ta an nd d I In ns st ta al ll la at ti io on n
The Vigor2110 must be placed erectly. Therefore you have to install a stand onto the
router to make it standing firmly. Please follow the figures listed below to finish the
installation.
c d
ef

11
2
2. .2 2 P Pr ri in nt te er r I In ns st ta al ll la at ti io on n
You can install a printer onto the router for sharing printing. All the PCs connected this
router can print documents via the router. The example provided here is made based on
Windows XP/2000. For Windows 98/SE/Vista, please visit www.draytek.com.
Before using it, please follow the steps below to configure settings for connected
computers (or wireless clients).
1. Connect the printer with the router through USB port.
2. Open Start->Settings-> Printer and Faxes.

12
3. Open File->Add a New Computer. A welcome dialog will appear. Please click
Next.
4. Click Local printer attached to this computer and click Next.
5. In this dialog, choose Create a new port Type of port and use the drop down list to
select Standard TCP/IP Port. Click Next.

13
6. In the following dialog, type 192.168.1.1 (router’s LAN IP) in the field of Printer
Name or IP Address and type IP_192.168.1.1 as the port name. Then, click Next.
7. Click Standard and choose Generic Network Card.
8. Then, in the following dialog, click Finish.

14
9. Now, your system will ask you to choose right name of the printer that you installed
onto the router. Such step can make correct driver loaded onto your PC. When you
finish the selection, click Next.
10. For the final stage, you need to go back to Control Panel-> Printers and edit the
property of the new printer you have added.
11. Select "LPR" on Protocol, type p1 (number 1) as Queue Name. Then click OK.
Next please refer to the red rectangle for choosing the correct protocol and UPR
name.

15
The printer can be used for printing now. Most of the printers with different
manufacturers are compatible with vigor router.
Note 1: Some printers with the fax/scanning or other additional functions are not
supported. If you do not know whether your printer is supported or not, please visit
www.draytek.com to find out the printer list. Open Support Center->FAQ->Sort
by product; select the model of the router and click on it; find out the link of Printer
Server FAQ; click the What types of printers are compatible with Vigor router?
link.
Note 2: Vigor router supports printing request from computers via LAN ports but not
WAN port.

16