Draytek Vigor2200 Series User manual

0. Preface .................................................................... 0-1
0.1 About This Manual ........................................ 0-2
0.2 Copyright Declarations ................................ 0-2
0.3 Trademarks ..................................................... 0-2
0.4 How To Become A Registered Owner ...... 0-2
0.5 Safety Instructions ......................................... 0-3
0.6 Warranty ............................................................ 0-3
0.7 European Community Declarations ............. 0-4
1. Getting Started .................................................. 1-1
1.1 Introduction ........................................................ 1-2
1.2Unpacking Your Vigor2200USB .................. 1-2
1.3 LED Indicators & Rear Panels Description......... 1-4
1.4 Detailed Features ................................................... 1-8
2. Installation & Setup ......................................... 2-1
2.1 Before you Begin .............................................. 2-2
2.2 Hardware Installation ....................................... 2-4
2.3 Setting up a Management PC ........................ 2-13
2.4 Using the Smart Start Wizard ...................... 2-19
2.5 Using the Web Configurator ....................... 2-24
Table of Contents

3. Basic Quick Setup......................................... 3-1
3.1 Administrator Password Setup ................................ 3-2
3.2 LAN TCP/IP and DHCP Setup ............................. 3-3
3.3 Internet Access Setup ....................................... 3-6
4. Advanced Setup ................................................ 4-1
4.1 Dynamic DNS Setup ..................................... 4-2
4.2 Call Schedule Setup ............................................... 4-5
4.3 NAT Setup ............................................................. 4-7
4.4 Static Route ....................................................... 4-14
4.5 IP Filter/Firewall Setup ....................................... 4-16
5. System Management ...................................... 5-1
5.1 Online Status ........................................................ 5-2
5.2 Time Setup ...................................................... 5-4
5.3 Management Setup ............................................. 5-6
5.4 Diagnostic Tools .................................................. 5-8
5.5 Reboot System .................................................. 5-14
5.6 Firmware Upgrade ............................................ 5-14

6. Troubleshooting & FAQ ............................... 6-1
6.1 Using the Telnet Terminal Commands .......... 6-2
6.2 Viewing Call Logs ............................................... 6-4
6.3 Viewing PPP Logs .............................................. 6-4
6.4 FAQs ....................................................................... 6-5
Virtual Private Network and Remote Access...........VPN -1
VPN.1 Introduction to VPNs and Remote Access .......
...............................................................................VPN-4
VPN.2 VPN IKE/IPSec Setup..............................VPN-5
VPN.3 VPN Remote Dial-in Access ...................VPN-7
VPN.4 VPN LAN-to-LAN Access......................VPN-11
VPN.5 VPN Connection Management............VPN-20
VPN.6 Example ..................................................VPN-21

0-1
0Preface
0.1 About This Manual
0.2 Copyright Declarations
0.3 Trademarks
0.4 How To Become A Registered Owner
0.5 Safety Instructions
0.6 Warranty
0.7 European Community Declarations

0-2
Preface
0.1 About This Manual (V1.2)
This manual is designed to assist users in using the
Vigor2200USB. Information in this document has been care-
fully checked for accuracy; however, no guarantee is given as
to the correctness of the contents. The information contained
in this document is subject to change without notice. Should
you have any inquiries, please feel free to contact our support
via e-mail, fax, or phone. For latest product info and fea-
tures, please visit our website.
0.2 Copyright Declarations
Copyright 2002. All rights reserved. This publication con-
tains information that is protected by copyright. No part may
be reproduced, transmitted, transcribed, stored in a retrieval
system, or translated into any language without written per-
mission from the copyright holders.
0.3 Trademarks
Microsoft is a registered trademark of Microsoft Corp. Win-
dows, Windows 95, 98, Me, NT, and 2000 are trademarks
of Microsoft Corp. Other trademarks and registered trade-
marks of products referred to in this manual are the proper-
ties of their respective owners.
0.4 How To Become A Registered Owner
Web registration is preferred. Alternatively, fill in the regis-
tration card and mail it to the address found on the reverse
side of the card. Registered owners will receive future prod-
uct and update information.

0-3
Preface
0.5 Safety Instructions
Read the installation guide thoroughly before you set up the
Vigor2200USB.
The Vigor2200USB is a complicated electronic unit that may
be repaired only be authorized and qualified personnel. Do
not try to open or repair the router yourself.
Do not place the router in a damp or humid place, e.g. a
bathroom.
The Vigor2200USB should be used in a sheltered area,
within a temperature range of +5 to +40 Celsius.
Do not expose the Vigor2200USB to direct sunlight or other
heat sources. The housing and electronic components may
be damaged by direct sunlight or heat sources.
Keep the packaging out of reach of children.
When you to dispose of the Vigor2200USB, please follow
local regulations on conservation of the environment.
0.6 Warranty
We warrant to the original end user (purchaser) that the
Vigor2200USB will be free from any defects in workman-
ship or materials for a period of three (3) years from the date
of purchase from the dealer. Please keep your purchase re-
ceipt in a safe place as it serves as proof of date of purchase.
During the warranty period, and upon proof of purchase,
should the product have indications of failure due to faulty
workmanship and/or materials, we will, at our discretion, re-
•
•
•
•
•
•
•

0-4
Preface
pair or replace the defective products or components, with-
out charge for either parts or labor, to whatever extent we
deem necessary to restore the product to proper operating
condition. Any replacement will consist of a new or re-manu-
factured functionally equivalent product of equal value, and
will be offered solely at our discretion. This warranty will not
apply if theproduct ismodified,misused,tamperedwith,dam-
aged by an act of God, or subjected to abnormal working
conditions.
The warranty does not cover bundled or licensed software of
other vendors. Defects which do not significantly affect the
usability of the product will not be covered by the warranty.
We reserve the right to revise the manual and online docu-
mentation and to make changes from time to time in the con-
tents hereof without obligation to notify any person of such
revision or changes.
0.7 European Community Declarations
We hereby declare that the Vigor2200USB is in compliance
with the essential requirements and other relevant provisions
of R&TTE Directive 99/5/EC.

1-1
1Getting Started
1.1 Introduction
1.2 Unpacking Your Vigor2200USB
1.3 LED Indicators & Rear Panel Description
1.4 Detailed Features

1-2
Getting Started
1.2 Unpacking Your Vigor2200USB
Your Vigor2200USB package should contain the items listed be-
low. If any item is missing or damaged, contact your dealer or our
Customer Service Department immediately.
• One Quick Start User Guide with warranty/registration
card
• One CD-ROM includes detailed User Manual in elec-
tronic form, latest released firmware, and utilities
• One AC/DC power adapter (black)
• One Ethernet LAN cable (blue) for connection to a com-
puter or hub
1.1 Introduction
The Vigor2200USB provides multiple users with efficient and reli-
able access over a DSL line to the Internet and corporate LAN for
using e-mail, sharing documents, Web surfing, file transfers, etc.
The broadband access protocol for the USB port supports PPPoE,
PPPoA. These protocols comply with USB-based DSL Modem
standards.

1-3
Getting Started

1-4
Getting Started
1.3 LED Indicators & Rear Panel Description
LED Indicators
There are eleven LEDs on the front panel; ACT, DSL, USB, LNK,
USB, LNK, VPN, P1, P2, P3 and P4.
ACT (Activity)
Blinks when power is supplied to the router and the router is run-
ning normally.
DSL
ON when the DSL modem is active.

1-5
Getting Started
USB1 Group:
USB
ON when the DSL modem is ready.
Blinking when there is data transferring between the
Vigor2200USB and the DSL modem.
LNK
ON when the PPP connection of the DSL modem is active.
USB2 Group:
USB
ON when the DSL modem is ready.
Blinking when there is data transferring between the
Vigor2200USB and the DSL modem.
LNK
ON when the PPP connection of the DSL modem is active.
VPN
ON when the VPN function is active.
P1, P2, P3, P4 (LAN)
ON when a network card or hub is connected.

1-6
Getting Started
Rear Panel Description
The router has a reset button, a power jack, four 10/100Base-T
RJ-45 switch ports, an Uplink button, and 2 USB ports on the rear
panel:
Reset
For firmware upgrades: Press and hold the button, then power ON.
The ACT and DSL LEDs will blink simultaneously (see section 5.5).
To restore default settings: While the device is running, press the
button and hold for more than five seconds. When the ACT LED
begins to blink rapidly, release the Reset button. The router will
restart with the default configuration
PWR
Only the supplied power adapter should be connected to the
power jack.

1-7
Getting Started
P1, P2, P3, P4
These are 10/100Base-TX Ethernet Switch ports. Connect your
PCs to these ports.
Uplink
For connecting to another hub/switch, press the Uplink button and
connect the other hub/switch to the P1 port.
USB
The DSL USB modem (Alcatel Speed Touch USB, or DynaMite
USB Modem) should be connected to one of these USB ports. For
an interoperable USB DSL modem list, contact DrayTek or your
dealer.

1-8
Getting Started
1.4 Detailed Features
The Vigor2200USB provides many built-in server and software fea-
tures to provide a convenient comprehensive solution for your SOHO
network.
1. Network Address Translation (NAT): NAT allows multiple
SOHO users to concurrently connect to an Internet Service Pro-
vider (ISP) using a single Internet access account.
2. Firmware Upgrade (TFTP) Server: Using this server and the
Firmware Upgrade Utility software, you may easily upgrade to
the latest firmware whenever enhanced features are added.
3. Web (HTTP) Server: A Web browser is the most common
tool used to surf the Internet. You may use Microsoft’s Internet
Explorer or a Netscape browser etc, to configure the router as
easily as surfing a website.
4. Domain Name Server (DNS) Proxy: The DNS proxy main-
tains a DNS cache, including a mapping table of domain names and
IP addresses. The proxy also remembers DNS query packets sent
through the router and saves them into its own DNS cache. For
enhanced speed, when a DNS query packet enters the
Vigor2200USB, the proxy searches its local DNS cache. If match-
ed, the Vigor2200USB sends an answer to the host that sent the
DNS query packet. Only umatched DNS queries require querying
a WAN Domain Name Server.

1-9
Getting Started
5. Telnet Terminal Server: The Telnet User Interface (TUI) is an
efficient method of configuring and managing routers. It utilizes a
traditional command-line user interface and is mainly for advanced
configuration, management, and troubleshooting.
6. Dynamic Host Configuration Protocol (DHCP) Server: This
server provides an easy-to-configure function for your local IP net-
work. It automatically assigns IP network configurations to local
PCs, such as IP address, IP netmask, gateway IP address, and
Domain Name Server etc.
7. Built-in Flash ROM: The Flash ROM memory saves the
Vigor2200USB firmware and configurations, even after power
down.
8. Point-to-Point Protocol over Ethernet (PPPoE) Client Sup-
port: The Vigor2200USB has a built-in PPPoE client for establish-
ing a DSL link connection with the ISP. There is no need to install a
further PPPoE driver on your computers.
9. Firewall: In addition to the built-in NAT mechanism, the
Vigor2200USB features another powerful firewall to protect your
local network, or to deny specified local users access to unauthor-
ized network services.
10. VPN: The Vigor2200USB supports to establish a private net-
work of computers that's partially connected over the internet. The
IPSec protocol is used for VPN (Virtual Private Network).

2-1
2Installation & Setup
2.1 Before you Begin
2.2 Hardware Installation
2.3 Setting Up a Management PC
2.4 Using the Smart Start Wizard
2.5 Using the Web Configurator

2-2
2.1 Before You Begin
1. Use only the power adapter supplied by us. Using an incorrectly
rated power adapter will result in damage to the router.
2. In case of emergency, unplug the power adapter first.
3. Locate the device in a clean location. Do not block the ventila-
tion slots on the rear panel.
4. Cables must be attached to the correct ports; to do otherwise
may result in damage to the router. Keep cables away from walk-
ways.
5. If you are a DSL user with USB ADSL modem, check that if
yourUSBADSLmodem is in the supportinglist.Ifnot,pleasecheck
the information on web to see if the router support it.
6. Before you set up the router, you need to know the router default
settings as shown on the next page:

2-3
FactoryDefault Settings:
Router
s
Default IP Network Settings:
IP Address: 192.168.1.1
Subnet Mask: 255.255.255.0
DHCP Server: Enabled
Start IP Address: 192.168.1.10
IP Pool Counts: 50
Web Configurator:
Username: admin
Password: <blank>
Note: Blank means no password required.
Telnet Console:
Password: <blank>
Note: Blank means no password required.
Management from the Internet:
Not allow.

2-4
B. Connecting to an External Ethernet Hub or Switch:
1. Attach the Ethernet cable (blue color cable) to any P1~ P4
port.
2. Connect the other end of the Ethernet cable to the external
Ethernet hub or switch.
2.2 Hardware Installation
2.2.1 Connecting the Power Adapter
1. Connect the power adapter to the power outlet on the wall
and to the PWR power jack on the rear panel of the router.
2. The ACT LED should be blinking once every 2 seconds.
2.2.2 Connecting to the Ethernet
A. Connecting to a PC:
1. Attach the Ethernet cable (blue color cable) to any P1 ~
P4 port.
2. Connect the other end of the Ethernet cable to your PCs
installed network interface card (NIC).
3. The LED indicators at both the Ethernet port and the NIC
should be ON.
Note:
If the Ethernet cable is not long enough to reach your
PCs, purchase a longer straight-through CAT. 5 UTP
or STP Ethernet cable.