Draytek Vigor 2927 Series User manual

Serie Vigor2927
Firmware version: V4.2.2.1
Dual WAN Security Router
(for RF model)
Version: 1.4
(For future updates, please visit the DrayTek website)
Date: September 8, 2021
Quick Start Guide

Cable RJ-45 (Ethernet)
AU/NZ Type Power Adapter
Antenna + Socket (for L models)
US/Taiwan Type Power Adapter
EU Type Power AdapterUK power adapter
vigor router
Antenna (for ac/ax models)
Quick Start Guide
1. Package content
28 whatts
Take a look at the package contents. If anything is missing or damaged, please contact
DrayTek or your dealer immediately. Also, the content is subject to the actual package.
.
The type of power adapter depends on the country in which the router will be installed. *Maximum
power consumption is

WAN2 / WAN1
2.2 Vigor2927ac / Vigor2927ax / Vigor2927Lac
(1)
DMZ
Switched on The LTE device is connected and ready to use.
The router is on and working normally.
The Internet connection is ready.
Off
Flicker
USB1 / USB2
Switched on
LED
Off
Switched on
The data is being transmitted.
DMZ function is enabled.
No.
The Internet connection is not ready.
LTE
Explanation
Off
The USB device is connected and ready to use.
The data is being transmitted.
state
Switched on
Off
The DMZ function is disabled.
Off
ACT
Flicker
Flicker
The router is turned off.
There is no USB device connected.
Flicker
The data is being transmitted.
Flicker
Fast: Data is being transmitted.
Slowly: LTE device is dialing.
The LTE device is not detected or has a serious
problem (for example, no SIM card, SIM pin error, SIM
disabled, etc.).

The wireless function is disabled.
The port is connected at 1000 Mbps.
The port is connected.
The port is connected with 10/100Mbps.
The port is disconnected.
QoS
Will flash slowly as traffic passes
Off
Switched on
WAN1, WAN2 / P6
Switched on
The port is connected with 10/100Mbps
Flicker
Switched on
Flicker
Switched on
Off
Off
The data is being transmitted.
The QoS function is inactive.
5G / 2,4G
left LED
Switched on
The QoS function is active.
right LED
Off
The port is disconnected.
left LED
The port is connected.
Switched on
5G/2.4G: Wireless hotspot with 5GHz/2.4GHz
bandwidth is ready.
The ACT and WLAN LEDs flash quickly and
simultaneously when WPS is working and will return to normal
after two minutes. (You need to set WPS within 2 minutes.)
The data is being transmitted.
The port is connected at 1000 Mbps.
Off
right LED
Off
wireless.
Flicker
AND P1-P5
(1)
(2)
WLAN: The wireless access point is ready.

- 2.4G (On) and 5G (On): By default.
Connector for local network devices or modem to access the
Internet.
WAN1
button pressed and released. For example,
USB1 ~ 2 / USB
Restore default settings. Usage: Power on the router (ACT LED blinks). Press
the hole and hold for more than 5 seconds. When you see the ACT LED start
blinking faster than usual, release the button. Then the router will reboot to the
factory default settings.
button once.
- 2.4G (off) and 5G (on): Press and release the
When the WPS function is enabled by the web UI, please press this button for more
than 2 seconds to wait for the client device to connect to the network via WPS.
twice.
Conector para dispositivo USB (for modem USB 3G / 4G or printer
or thermometer).
- 2.4G (On) and 5G (Off): Pressed and released the button
The wireless band will be switched/changed according to the
button three times.
wireless LAN
- 2.4G (Off) and 5G (Off) - pressed and released the
No. Interface
ON / OFF / WPS
Factory reset
Description
(3)
(4)
(5)

ON OFF
AND P1-P5
(For L model).
It is a switchable port. It can be used for LAN connection or WAN connection
according to the settings configured in WUI.
SIM 2 / SIM 1
(For L model).
Connector for installation of WLAN antennas.
Connector for installation of LTE antennas.
Connectors for local network devices.
Connector for local network devices or modem for
Slots to install SIM card.
(For WiFi model)
Power switch.
Connector for power adapter.
WAN2/P6
Internet access.
PWR
(7)
(6)
(8)
(9)

el "ac"
3. Hardware installation
3.1 Network connection
3. Connect one end of the power adapter to the router's power port on the rear panel and the
other end to a wall outlet.
model as an example.)
2. Plug one end of an Ethernet cable (RJ-45) into one of the LAN ports on the router and the other
end of the cable (RJ-45) into the Ethernet port on your computer.
Before you start configuring the router, you need to connect your devices correctly. (For
hardware connection, we take
5. The system begins to boot. After completing the system test, the ACT LED will turn on.
1. Connect the Cable Modem / DSL Modem / Media Converter to any WAN port of the router with
Ethernet cable (RJ-45).
will light up and start blinking. (For detailed information on the status of the LEDs, see section 3.
Explanation of the panel)
This section will guide you to install the router through the hardware connection and configure the settings of
the router through the web browser.
4. Turn on the device by pressing the power switch on the rear panel.

Use
3.2 Wall installation
The recommended drill diameter should be 6.5mm (1/4”).
Vigor router has keyhole mounting slots at the bottom.
2. Drive the screws into the wall using the appropriate type of wall plug.
1. Drill two holes in the wall. The distance between the holes will be 168 mm.
3. When you are done with the procedure, the router is securely mounted to the wall.

4. Software configuration
Use
Use If you cannot access web settings, please go to
"Troubleshooting" in the User Guide to troubleshoot
and resolve your issue.
To access the Internet, finish the basic setup after completing the hardware installation.
Open a web browser on your PC and type http://192.168.1.1. A pop-up window will open to request
the username and password. Enter "admin / admin" as the username / password and click Access.
The quick start guide is designed to make it easy for you to set up your router to access the Internet.
You can directly access the Quick Start Wizard through the web user interface. Make sure your PC connects
to the router successfully.
You can simply set your computer to obtain IP dynamically from the router or
set the computer's IP address to be the same subnet as Vigor router's default IP
address 192.168.1.1. For detailed information, please refer to - User
Guide Troubleshooting.