Dreamline Unidoor Lux D SHDR -23297210 Series User manual

UNIDOOR LUX (STYLE D) Ver 2 Rev 9 09/2016
1
IMPORTANT
DreamLine®reserves the right to alter, modify or redesign products at any time without prior notice.
For the latest up-to-date technical drawings, manuals, warranty information or additional details
please refer to your model’s web page on DreamLine.com
Style D
Please read these instructions carefully before installing. If you have any questions regarding
installation, please contact our technical support specialists Monday through Friday 8AM –
7PM and Saturday 9AM-5PM EST at Phone: [phone], Fax: [phone] or e-mail our
technical support group at [email protected]
For more information about DreamLine®products please visit DreamLine.com
UNIDOOR LUX (STYLE D)
SHOWER DOOR GLASS PANEL INSTALLATION INSTRUCTIONS
Style D
Right side panel installation shown

UNIDOOR LUX (STYLE D) Ver 2 Rev 9 09/2016
2
Model #s
SHDR-23297210-##
SHDR-23307210-##
SHDR-23317210-##
SHDR-23327210-##
SHDR-23337210-##
SHDR-23347210-##
SHDR-23357210-##
SHDR-23367210-##
SHDR-23377210-##
SHDR-23387210-##
SHDR-23397210-##
SHDR-23407210-##
SHDR-23417210-##
SHDR-23427210-##
SHDR-23437210-##
SHDR-23447210-##
SHDR-23457210-##
SHDR-23467210-##
SHDR-23477210-##
SHDR-23487210-##
SHDR-23497210-##
SHDR-23507210-##
SHDR-23517210-##
SHDR-23527210-##
SHDR-23537210-##
SHDR-23547210-##
SHDR-23557210-##
SHDR-23567210-##
SHDR-23577210-##
SHDR-23587210-##
SHDR-23597210-##
SHDR-23607210-##
##=finish
01- Chrome
04- Brushed Nickel
06- Oil Rubbed Bronze
09- Satin Black

UNIDOOR LUX (STYLE D) Ver 2 Rev 9 09/2016
3
Preparation
1. Prior to installation, examine all boxes and packages for shipping damage and compare the piece
count with your packing slip. After opening all boxes and packages read this introduction carefully.
Check that all of the needed parts are included in the package by checking off the components on
the “Detailed Diagram of Shower Door Components”. If the unit has been damaged, has a
finishing defect, or has missing parts, please contact our customer support department within
3 business days of the delivery date. Please note that DreamLine®will not replace any
damaged products or missing parts free of charge after 3 business days or if the product has
been installed. Feel free to contact DreamLine®if you have any questions and please provide an
order number, job name or other proof of purchase to help identify the original order.
2. Please note that you should consult your local building codes with questions about
installation compliance standards. Building and plumbing codes may vary by location, and
DreamLine®is not responsible for code compliance standards for your project and will not
accept any returns.
3. If this unit is going to be installed in a new construction, please, install all of the required plumbing
and drainage before installing the shower. Use a competent and licensed (if required by local
code) plumber for all plumbing installation.
4. Please make sure that prior to beginning the installation, the surfaces are leveled and solid and will
be able to support the total weight of the unit. Also make sure the walls are at right angles.
Irregular installation surface level, radius corners or improper angle of side walls will result in
serious problems for your installation. Please, note that some adjustments and drilling may be
necessary during the installation process.
5. Please protect all primary surfaces of the product during installation. Never set your glass down
directly onto a tile floor. Leave corner protectors in place until necessary to remove them. Always
use a piece of wood or cardboard to protect the bottom edge and corners of the glass prior to and
during installation.
6. This unit must be installed upon a finished threshold and against finished walls.
7. Note: The installation of this unit requires that you drill down into the threshold.
8. This model requires a minimum 5/8” of flat threshold space for installation.
NOTE: This model is reversible for left or right hand installation. This manual will show the installation
of the panel on the right side. For a left side panel installation, simply begin on the opposite wall and
reverse the orientation of the parts as necessary.

UNIDOOR LUX (STYLE D) Ver 2 Rev 9 09/2016
4
Tools Required
Caulk Tape
Measure Pencil Screwdriver
Phillips Drill bit
Level Gun
Caulk Drill
Electric Hammer
Drill bit
(Ø=5/16") (Ø=1/8")
Knife

UNIDOOR LUX (STYLE D) Ver 2 Rev 9 09/2016
5
Detailed Diagram of Glass Panel Components
Packing List
11
Stationary glass
1pc
18
Bottom bracket
1pc
12
Support bar *
1pc
19
Anti-Water strip (inline panel)
1pc
13
Wall anchor *
2pcs + 1pc
20
Anti-water strip (enclosure)**
1pc
15
Big flat head screw ST4.2×55
2pcs
23
Countersunk screw ST4.2x40*
1pc
16
Round head screw ST4.2×35
1pc
24
Wall bracket
2pcs
17
Decorative screw cover
1pc
NOTE: Unpack your unit carefully and inspect it. Identify all parts using the detailed diagram and
packing list in this manual as a reference. Before discarding the carton, check for small hardware bags
that may have fallen to the bottom of the box. If any parts are damaged or missing, please contact
DreamLine®for replacement. The shipping boxes may contain extra parts not used in your model
configuration.
* ATTENTION: All parts that are marked with the star (*) not provided with 6” Stationary panel.
** ATTENTION: Anti-Water strip (enclosure) (20) used for 30”- 34” Return stationary panel
installation (STYLE E).
11
13
15
16
17
18
19
20
24
12
23
The glass surface
with the ClearMax™
label must be
installed to face
inside of the shower

UNIDOOR LUX (STYLE D) Ver 2 Rev 9 09/2016
6
Style “D”: 6” Small or 14”-30” Large Stationary Panel Installation
NOTE: The Unidoor shower door needs to be
installed prior to proceeding with the following
Stationary Glass installation instructions. Please
see the Single Shower Door installation manual
included in the door packaging for complete
shower door installation instructions. Before you
begin the installation, please recheck your shower
opening size. Specific size information can be
found on our website at Dreamline.com.
NOTE: The 22” In-Line Stationary Glass Panel is
the primary example shown throughout this
installation manual. Use the following installation
procedures when installing a 6” In-Line Stationary
Glass Panel with the exclusion of the Support Bar
(12). See page 8 for more information.
NOTE: The Unidoor hinge is factory set to over
close 8°. The following procedure is recommended to
ensure proper alignment of the panel glass and the door
glass.
1. Align the Door so that it is perpendicular to the wall and
parallel to the threshold. Measure across the bottom span of
the Door and threshold on the outside of shower and
determine an equal value.
Mark a line on the threshold base on the handle side
See Fig. 1 for details.
Value
inside
outside
outside
inside
Door
Fig. 1
2
1

UNIDOOR LUX (STYLE D) Ver 2 Rev 9 09/2016
7
NOTE: Use parts from “Detailed Diagram of Glass Panel Components”for the Stationary
Glass assembly and installation
2. Mount the two Wall brackets (24) through the
notches on the Stationary glass (11).
Press the Anti-water strip (inline panel) (19)
onto the vertical edge of the Stationary glass.
Attach the Bottom Bracket (18) through the
bottom hole of the Stationary glass.
See Fig. 2 for details.
3. Carefully butt the Stationary glass (11) up against the wall
vertically.
See Fig. 3 for details.
3
2
inside
outside
inside
outside
inside
outside outside
inside
inside
outside
4
3
2
1
5
6
Fig. 2
Fig. 3

UNIDOOR LUX (STYLE D) Ver 2 Rev 9 09/2016
8
4. While securely holding the Stationary glass (11)
close the Glass Door and align the Stationary glass
to it. Use the door mark that was made in step #1
on the threshold as a reference to ensure that the
Door is perpendicular to the wall.
If needed, adjust the position of the Stationary
glass so that the Anti-Water strip (inline panel)
(19) makes tight contact to the Glass Door from
top to bottom.
NOTE: The top of the Stationary glass must be
leveled with the Glass door.
Outline the position of the Wall brackets (24) on
the wall from inside the shower.
Mark the drilling hole of the Bottom bracket (18)
on the shower base or threshold through the oval
notched hole.
See Fig. 4 for details.
5. Open the Glass Door and carefully set the
Stationary glass (11) aside. Remove the Wall
brackets (24) and Bottom bracket (18) from the
Stationary glass.
Replace the Wall brackets to the outlined positions
that were made in step #4 and mark the drill holes
on the wall.
Drill the holes using a Ø 5/16”drill bit, insert the
Wall anchor (13) and fasten the Wall brackets to
the wall with the Big flat head screws ST4.2×55
(15).
See Fig. 5 for details.
Ø 5/16"
inside
outside
inside
outside
outside
inside
outside
inside
inside
Door
Align stationary glass
and glass door inside
1/16"-1/8"
Stationary
glass
inside
4
3
2
1
5
4
3
2
1
5
6
Fig. 4
Fig. 5

UNIDOOR LUX (STYLE D) Ver 2 Rev 9 09/2016
9
6. Drill the hole into the shower base or threshold for the
Bottom bracket (18) using Ø 1/8”drill bit at the drill mark
that was made in step #4.
Use the Round head screw ST4.2x35 (16) along with a raised
white washer to attach the Bottom Bracket to the shower
base or threshold.
See Fig. 6 for details.
7. Move the Stationary Glass (11) back into position
and tighten it up to the Wall Brackets (24).
Secure the Bottom Bracket (18) to the
Stationary Glass.
Cover the Bottom Bracket screw head with
Decorative screw cover (17).
See Fig. 7 and Fig. 8 for details.
outside
inside
Ø 1/8"
outside
inside inside
inside inside
inside
outside
4
3
2
1
5
Fig. 6
Fig. 7
6
2
1

UNIDOOR LUX (STYLE D) Ver 2 Rev 9 09/2016
10
ATTENTION:
If width of the Stationary glass (11) is 12”or
larger, the Support bar (12) must be installed for
stability.
8. Locate the Support bar (12).
Adjust the Support bar at an angle that will provide
adequate support for the glass to the wall. Level it
horizontally. Hold it firmly and outline the bracket’s
position on the wall. Remove the Support bar and
detach the wall bracket from it. Place the wall bracket
against its outlined position on the wall and mark the
drilling hole.
Drill the hole using Ø5/16” drill bit, insert the Wall
anchor (13) and fasten the wall bracket to the wall
with the Countersunk screw ST4.2×40 (23). Attach
the Support bar to the wall as shown in Fig. 9.5 and
tighten the set screws and the glass holding screw to
secure the glass.
See Fig. 9 and Fig. 10 for details.
NOTE: Make sure to use clear rubber gasket to
prevent glass to metal connection.
inside
outside
Ø5/16"
inside
Fig. 9
1
3
5
2
4
6
Fig. 8

UNIDOOR LUX (STYLE D) Ver 2 Rev 9 09/2016
11
9. Apply good quality mildew-resistant silicone along the
connection of the Stationary glass (11) with the walls and
the threshold.
Allow 24 hours for the silicone to fully cure before using
the shower.
See Fig. 11 for details.
Fig. 10
waterproof
silicone
inside
Fig. 11

UNIDOOR LUX (STYLE D) Ver 2 Rev 9 09/2016
12
Product Maintenance
BASES and BACKWALLS: To ensure long lasting life for your acrylic back walls: wipe them off
after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream
based cleaners. Avoid the use of aerosol spray cleaners. Never use abrasive cleansers, metal
brushes or scrapers that could scratch or dull the surface.
GLASS: To ensure long lasting life for your glass shower products: wipe them off after each use
with a soft cloth. Rinse and wipe off the glass using either a soft cloth or a squeegee to prevent
soap buildup and water spots (Hard water can etch the surface of the glass over time if left to dry).
To prevent scratching the surface: never use abrasive cleaners or cleaning products that contain
scouring agents. Never use bristle brushes or abrasive sponges that may scratch the surface.
HARDWARE: To ensure a long lasting finish: wipe off the metal parts after each use with a soft
cloth. Do not use abrasive cleaners or cleaning products containing ammonia, bleach or acid. If
accidentally used, rinse the surface as soon as possible to prevent damage to the finish (peeling or
corrosion). After cleaning the polished finishes, rinse thoroughly and wipe dry with soft cloth.
Clean stainless steel surfaces at least once a week. When applying stainless steel cleaner or polish
to stainless steel hardware, work with (not across) the grain. Never use an abrasive sponge or cloth,
steel wool or wired brush as these may permanently scratch the surfaces.
NOTE: To maximize the life of your door, it is important to regularly inspect the glass and
other hardware for misalignment, proper attachment, and/or damage. Contact DreamLine
with any questions or concerns.

UNIDOOR LUX (STYLE D) Ver 2 Rev 9 09/2016
13
TEL: [phone]
FAX: [phone]
DREAMLINE.COM
For more information on DreamLine®Shower Doors and Enclosures please visit DreamLine.com