Dreamline TETRA User manual

Rev.1.1 Page 1
TETRA Shower Enclosure Installation Manual
Important
Please read carefully the following instructions before installing your shower door. If you have
any questions on this shower enclosure installation, please call our technical support specialists
Monday to Friday 9:00AM –5:00PM EST at 1-866-731-8378 Option 3 or e-mail our technical
support group at [e-mail]
Our product may have changes without prior notice

Rev.1.1 Page 2
Preparation
1. After opening the boxes, read this introduction carefully, check all the packed parts are
complete by cross checking all the components against the “Detailed Diagram of Shower
Door Components”. Examine for shipping damage. If the unit has been damaged or has a
finishing defect, please contact your local distributor within 3 business days. Please note that
Bath AuthorityTM / DreamLine TM will not replace any damaged product or parts free of
charge after 3 business days or if the product has been installed. Contact your
distributor or DreamLine if you have any questions.
2. Please note that you should consult your local building codes on questions on
installation compliance standards. Building and plumbing codes vary by location, and
DreamLine is not responsible for code compliance standards for your project.
3. Install all of the required plumbing and drainage before securing the shower. Use a
competent and licensed (if required by local code) plumber for all plumbing
installation.
4. Please insure that prior to the installation the floor is leveled and solid and will be able to
support the total weight of the unit and its occupant. Also make sure the walls are at right
angles. While some adjustment in leveling of the tray is possible, irregular floor level or
improper angle of side walls will result in serious problems for your installation. Please, note
that there are some adjustments and drilling might be necessary during the installation
process.
5. For the shower tray installation, please refer to our Shower Tray Installation Manual.
Once the tray is installed and the interior wall is finished, then you can start the
installation of your shower enclosure.
Tools Required

Rev.1.1 Page 3
Detailed Diagrams of Shower Enclosure Components
Packing List
01
Wall profile 1
1pc
16
Pivot assembly (top and bottom)
1pair
02
Glass profile 1
1pc
17
Pivot bracket
2pcs
03
Glass profile 2
1pc
18
Washer
2pcs
04
Wall profile 2
1pc
19
Wall Anchor
13pcs
05
Glass door
1pc
20
Screw M4×16 with washer
4pcs
06
Return glass
1pc
21
Decorative cover
1pc
07
Handle
1pc
22
Decorative Plug
6pcs
08
Top bar
1pc
23
Countersunk screw ST4.2×16
6pcs
09
Magnetic strip
1pair
24
Countersunk screw ST4.2×25
3pcs
10
Anti-water strip
1pc
25
Round head screw ST4.2×25
1pc
11
Bottom anti-water strip
1pc
26
Round head screw ST4.2×30
13pcs
12
Support Bar Wall bracket
1pc
27
Hex socket round head bolt M6×12
1pc
13
Support Bar Glass bracket
1pc
28
Hex socket flat head bolt M6×12
1pc
14
Bottom bracket
1pc
29
Allen key 4mm, 5mm each
1 set
15
Pivot retainer
2pcs
30
After you have checked that all components are there, you will be ready to start the
installation of your DreamLine shower enclosure.

Rev.1.1 Page 4
Installation
1. Locate the Wall profile 1 (01) in the package. Refer to dimensions in fig. 1 to locate the
proper position for it according to the measurement. Outline the external position of the wall
profile. Use predrilled holes in the aluminum profile to mark holes for drilling. Drill the holes
using drill bit 5/16” and push the Wall Anchors (19)into the holes.
2. Run a bead of silicone along the wall profile length. Push the Pivot retainer (15) into the top
and bottom sides of the Wall profile 1.Place the Wall Profile 1 onto the threshold against the
marked line. Secure the Wall Profile 1 and the Pivot retainers (15) at the top and bottom
ends of the profile with Screws ST4.2×30 (26). See Fig. 1 for details.
3. Repeat Step 1 to attach the Wall profile 2 (04) to the wall (this wall profile will have no
pre-cut seat for pivot retainers). Doesn’t require pivot retainers. See Fig. 2 for details.
4. Locate the short Glass profile 1 (2). Push the upper Pivot bracket (17)into the top groove
of the Glass profile; then secure it to the profile with Countersunk screws ST4.2×25 (24)
and M4×16 bolt (20). Repeat the same steps for the bottom pivot bracket. See Fig 3 for
details.
5. Attach the bottom Pivot assembly (16) onto the Pivot bracket (17). Make sure that the
Washer (18) is in between the pivot assembly and the pivot bracket. The washer may
already be placed on the pivot assembly pin or inside the pivot bracket. Repeat the same for
the top pivot assembly. The pivot assembly and the pivot bracket edges should be aligned.
The bolt side should face inward. Remove the back fastener from the pivot assembly. Set
the Glass door (05)so the holes are aligned. Make sure the rubber gaskets are in between
the glass and the metal parts. Secure the glass with the back fastener using the provided
bolts. See fig. 4 for details.
6. Mount the Handle (07) on the glass door. See fig. 5 for details.
7. Push the assembled glass door into the groove of the Wall profile 1. Secure the Upper
pivot bracket (17) and the Upper pivot retainer (15) with Hex Socket round head bolt
M6×12 (27). See Fig. 6, 7 for details.
8. Apply silicone along the full length of the Glass profile 2 (03) channel and then push the
Return glass (06) into the channel. (Note that the hole in the return glass should be located
at the bottom and close to the glass door). Gently tap on the Glass profile 2 (03) with the
rubber hammer through the wooden block so the Return glass slides inside the Glass
profile 2. See fig. 8 for details.
9. Push the Magnetic strips (9) on the edges of the return glass and the swing door, the
Anti-water strip (10) –inside the glass profile channel and the Bottom anti-water strip (11)
on the bottom of the door. Make sure the glass door is leveled and plumbed and then tighten
up the Hex socket round head bolt M6×12 (27). See Fig. 9 for details.
10.Adjust the positions of the glass door and the return glass to ensure that the door is closing
tightly. Drill the holes at the top, middle and bottom in the wall profile 1, and secure it to the
glass profile 1 with Countersunk screws ST4.2×16 (23) and cover the exposed screw
heads with Decorative plugs (22). See Fig. 10 for details.
11.Repeat Step 10 to attach the Wall profile 2 to glass profile 2. See Fig. 11 for details.
12.Place the Hex socket flat head bolt M6×12 (28) to the bottom Pivot bracket (17) or you
can drill through the screw hole, apply silicone and secure it using Countersunk screw
M4.2 ×25 (24). See Fig. 12 for details.
13.Attach the Bottom bracket (15) on the stationary glass and drill through the slotted hole of
the bracket. Screw the bracket to the threshold with the Round head screw ST4.2×25 (25)
and cover it with the Decorative cover (21). See fig. 13 for details.
14.Find the Support bar (08)and attach the Support bar wall bracket (12) and Support bar
glass bracket (13) to the support bar. Loosen the glass holding set-screw on the Glass

Rev.1.1 Page 5
bracket and place the bracket on the Return glass at a proper position. Adjust the position
of the wall bracket on the wall to ensure that the bar is leveled and parallel to the Glass
door. When the bar is aligned in place, outline the position for the Wall bracket. Remove
the Wall bracket, mark the screw hole and drill it, insert the Wall anchor (19). Attach the
Wall bracket to the wall with the Screw ST4.2×30 (26). Insert the end of the support bar
into the Wall bracket and attach the other end to the Glass bracket. Tighten up the
set-screw on the glass bracket. (Do not forget to put the plastic gasket between the
glass and metal.) Gently push the return glass from outside and check if the door is closing
tightly and then tighten up the holding set-screws on the Wall bracket. See fig. 14 for
details.
15.Seal with silicone between the shower tray and the stationary glass, between the wall and
the wall profiles. See fig. 15 for details.
If you want your shower enclosure to be installed in a different configuration, you can
simply switch the positions of wall profile 1 and wall profile 2.
Fig. 1 Fig. 2

Rev.1.1 Page 6
Fig. 3 Fig. 4
Fig. 5 Fig. 6

Rev.1.1 Page 7
Fig. 7 Fig. 8
Fig. 9 Fig. 10

Rev.1.1 Page 8
Fig. 11 Fig. 12
Fig. 13 Fig. 14

Rev.1.1 Page 9
Fig. 15
Maintenance
1. Tempered glass can be clean with nonabrasive bathroom cleaner or any glass cleaner
you use elsewhere in your home. Rinse off any glass cleaner that gets on the aluminum
as soon as possible to avoid damage to the anodized surface. Avoid striking it with any
sharp or hard objects. Such damage can cause either immediate or delayed breakage of
tempered glass.
2. The aluminum in your shower door is durable and resistant to water damage. It is
advisable, but not necessary to wipe it with your towel after your shower. Clean it as
often as needed to keep the buildup off. Never use any type of abrasive cleaner. Use
only a soft damp cloth and nonabrasive bathroom cleaners.