Dreamline ENIGMA User manual

ENIGMA Shower Enclosure Installation Manual
Important
Please read carefully the following instructions before installing your shower door. If you have
any questions on this shower Enclosure installation - please call our technical support
specialists Monday to Friday 9:00AM –5:00PM EST at 1-866-731-8378 Option 3 or e-mail our
technical support group at [e-mail]
Our product may have changes without prior notice
Attention: This enclosure is extremely heavy and requires
professional installation.

Rev. 1.1.
2
Preparation
1. After opening the boxes, read this introduction carefully, check all the packed parts are
complete by cross checking all the components against the “Detailed Diagram of Shower
Enclosure Components”. Examine for shipping damage. If the unit has been damaged or
has a finishing defect, please contact your local distributor within 3 business days. Please
note that Bath AuthorityTM / DreamLine TM will not replace any damaged product or
parts free of charge after 3 business days or if the product has been installed. Contact
your distributor or DreamLine if you have any questions.
2. Please note that you should consult your local building codes on questions on
installation compliance standards. Building and plumbing codes vary by location,
and DreamLine is not responsible for code compliance standards for your project.
3. Please ensure that prior to the installation the floor is leveled and solid. Also make sure the
walls are at right angles. While some adjustment in leveling of the door is possible, irregular
floor level or improper angle of side walls will result in serious problems for your installation.
Please note that there are some adjustments and drilling might be necessary during the
installation process.
4. This unit has to be installed against finished floor and walls.
5. This shower enclosure requires 3 1/2" wide threshold or installation space.
6. Please note, step 3 and step 6 are for installation of the enclosure to the wall
using anchors. However, the manufacturer strongly suggests installing this
heavy enclosure on preinstalled 2x4 wood reinforcement behind the wall and
attaching the Wall brackets to it.
Tools Required

Rev. 1.1.
3
Detailed Diagram of Shower Enclosure Components
1
2
34
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20 21
22
Packing List
01
Stopper
2pcs
12
Guide block
1pc
02
Front stationary glass panel
1pc
13
Door edge strip
1pc
03
Running rail
1pc
14
Threshold cover
1pc
04
Roller
4pcs
15
Threshold
1pc
05
Sliding door
1pc
16
Countersunk screw ST4.2×30
6pcs
06
Handle
1pc
17
Anti-water strip
2pcs
07
Glass bracket
2pcs
18
Small anchor 5/16″
9pcs
08
Wall bracket
2pcs
19
Wall & Bottom Return glass Brackets
3pcs
09
Large anchor 3/8″
1pc
20
Glass connector
1pc
10
Round head screw ST6×45
1pc
21
Screw ST4.2×30
3pcs
11
Allen keys 3, 4 and 5mm
1set
22
Return glass panel
1pc
After you have checked that all components are there, you will be ready to start the
installation of your DreamLine shower enclosure.

Rev. 1.1.
4
Installation
1. Select the proper place to install the shower enclosure. Refer to the shower enclosure plan
for dimensions. Mark out the threshold position on the floor. See fig. 1 for details.
2. Locate the Threshold (15) in the package and place it to the desired position. Mark the
holes for drilling on the floor. Remove the threshold, drill the holes in the floor and insert
Small anchors 5/16″ (18).Apply silicone on the bottom of the Threshold,place it back into
the chosen position and attach it to the floor with Countersunk screws ST4.2×30 (16). See
fig.2 for details.
3. a) Take the Return glass panel (22) and the Wall & Bottom Brackets for Return Glass
(19). Attach the brackets to the glass. See fig. 3&4 for details.
Note: Parts of the Wall & Bottom Return Glass Brackets with the mounting holes should face
inward so that when the glass panel is in place, mounting bolts are only visible from the inside.
b) Refer to the shower enclosure plan for dimensions and mark them out on the wall.
Position the glass according to the dimensions provided in the diagram against the end of
the Threshold. Level the return glass performing necessary adjustments to ensure that the
return glass is parallel to its opposite wall and square against the back wall. See fig. 5 for
details.
c) Mark the bracket position. Detach the Glass Brackets from Return glass panel. Using
brackets mark mounting holes for drilling (two on the wall and one on the floor), and then drill
the holes. Insert Small anchors 5/16″ (18). Secure the wall mounting part of the brackets to
the wall with Screw ST4.2×30 (21). See fig. 6&7 for details.
d) Set the Return glass panel against the installed wall mounting parts of the bracket from
outside and secure it to the fastening bracket parts with bolts and gaskets provided. See fig.
8 for details.
Before you install the Front stationary glass panel (02), you have to take the Sliding
door (05) into the shower room and lean it on the wall.
4. Attach the Running rail (03) to the Front stationary glass panel (02) with preinstalled
Glass brackets (07).Slide the Stoppers (01) from each end of the running rail and
temporarily secure them on the rail. Then slide the Wall brackets (08) on each end of the
Running rail and temporarily secure them as well. See fig. 9&10 for details.
5. a) Attach the Glass connector (20) to the Return glass panel. See fig. 11-3. Place the
Front stationary glass panel on the threshold and push the bottom edge into the groove of
the Threshold. Push the Stationary glass panel against the wall. Loosen the Wall bracket
to attach the Running Rail to the Glass connector on the Return Glass panel. (Please
note that the Running rail should now be inside the enclosure) See fig. 11 for details.
b) Level the glass and the Running rail. If a horizontal adjustment is required, adjust it in the
Glass brackets and the Glass connector. See fig. 12 for details.
c) When the Front stationary glass and the Running rail had been leveled, slide the Wall
bracket on the rail against the wall and mark its position with a pencil. Remove the glass
panel. Using the Wall bracket mark the hole for drilling on the wall and drill the hole. Insert
the Large anchors 3/8″ (9) and screw the male part of Wall bracket onto the wall using the
Round head screw ST6×45 (10) (you only need to use one of the two male parts detached
from the wall brackets).
d) Apply a small amount of silicone along of the Threshold channel. Place the Front
stationary glass back in position and attach the Wall brackets to the male part on the wall
and on the Return glass panel. Tighten the fastening set-screws with provided Allen Key
on the Wall brackets to secure the Running rail. See fig. 14 for details.

Rev. 1.1.
5
6. Place the Guide block (12) on the floor and parallel it to Stationary glass panel with its
edge flush with the glass vertical edge. Take a measurement to ensure the distance from the
outer surface of the glass to the center line of the guide block is 2 3 /16″, hold it firmly and
mark hole positions on the floor. Remove the block, drill the holes in the floor, insert Small
anchors and then secure it onto the floor with Countersunk screw ST4.2×30 (16). See fig.
15 for details.
7. Attach two top Rollers (04) onto the Sliding door (05). Suspend the door by hanging the
rollers onto the Running rail and slide the bottom edge of the Sliding door in the groove of
the Guide block. Adjust the fasteners on both top rollers to ensure that the bottom edge of
the glass does not touch the bottom of the guide block. Then mount two lower Rollers (04)
onto the door to secure the door to the Running rail. Secure it in place. See fig. 16&17 for
details.
8. Push the Threshold cover (14) onto the threshold when the door is in the opened position.
Mount the Handle (06) onto the door. See fig. 18 for details.
9. Push on the Door edge strip (13) on the sliding door and also push on the Anti-water strip
(17) on the stationary glass and the sliding door. See fig. 19 for details.
10.Adjust both Stoppers (01)to ensure that they are positioned upright and the door is in its
maximum opening and closing range. See fig. 20 for details.
11.Seal with silicone between threshold and floor and between glass panels and walls. See fig.
21 for details.
Shower Enclosure Plan

Rev. 1.1.
6
1
2
3
4
5
Fig. 1 Fig. 2
1
2
3
4
Fig. 3 Fig. 4

Rev. 1.1.
7
1
2
3
4
5
6
Fig. 5 Fig. 6
1
2
3
4
5
6
Fig. 7 Fig. 8

Rev. 1.1.
8
1
2
3
4
Fig. 9 Fig. 10
1
2
3
4
Fig. 11 Fig. 12

Rev. 1.1.
9
5
1
2
3
4
Fig. 13 Fig. 14
1
2
3
4
1
2 4
3
Fig. 15 Fig. 16

Rev. 1.1.
10
1
2
1
2
Fig. 17 Fig. 18
1
2
1
2
Fig. 19 Fig. 20

Rev. 1.1.
11
Fig. 21
Maintenance
1. Tempered glass can be cleaned with nonabrasive bathroom cleaner or any glass cleaner
you use elsewhere in your home. Rinse off any glass cleaner. Avoid striking it with any
sharp or hard objects. Such damage can cause either immediate or delayed breakage of
tempered glass.
2. Maintenance of the wheel:
A: Use a small amount of the lubricating oil to keep roller movement smooth.
B: Adjust wheel screw periodically to guarantee moving door effective bearing and
sliding.

© 2012 Bath Authority LLC.
All Rights Reserved.
DREAMLINE™LIMITED WARRANTY
This is Bath Authority LLC’s (“DreamLine”) exclusive written warranty effective April 2, 2012
This warranty extends only to the original owner/end-user for household use only and is not transferable to a subsequent owner. This warranty applies only
to DreamLine™ products purchased from an authorized dealer and installed in United States or Canada. Proof of purchase (original sales receipt) must be
provided with all warranty claims. In no event shall the liability of DreamLine™ exceed the purchase price of the unit.
If DreamLine™ shower & tub doors, shower enclosures and shower bases are used commercially, DreamLine™ warrants such products to be free from
defects in material and workmanship for one (1) year from initial date of purchase from an authorized dealer, with all other terms of this warranty applying
except duration. If DreamLine™ vanities, vessel sinks and shower columns are used commercially, DreamLine™ warrants such products to be free from
defects in material and workmanship for three (3) months from initial date of purchase from an authorized dealer, with all other terms of this warranty ap-
plying except duration. DreamLine™ Jetted and Steam Shower Cabins are not intended for commercial use and there is no warranty extended
for these products for commercial use.
DreamLine™ hereby disclaims all warranties for products sold as dealer or store displays. DreamLine™ hereby disclaims all warranties for products used outside of
the United States or Canada whether expressed or implied, including but not limited to the implied warranties of merchantability and tness for a particular purpose.
DreamLine™ will, at its election, repair, replace with product of equal value or make appropriate adjustment where DreamLine’s analysis or inspection of
warranty claim discloses any such defects occurring in normal usage within the warranty period. DreamLine warranty obligation shall be discharged upon
tender of replacement or repair. Purchaser’s refusal to accept the tender terminates warranty obligation.
Cost of freight for returning products to DreamLine™ for repairs or replacement under this limited warranty are the responsibility of the customer. Cost of
freight associated with shipping of replacement product or parts to the customer may be charged to customer. Any product replaced or repaired during the
warranty period will be covered only for the remaining period of the original warranty. In no event will DreamLine be liable for costs of repair or replacement
of any installation material, including but not limited to tiles, marble, etc. DreamLine™ is not responsible for installation, removal or reinstallation
costs of any product requiring warranty services.
Improper modication or alteration of any DreamLine™ products will void the warranty. DreamLine product installations and repairs must be performed
by either a DreamLine authorized agent or a licensed experienced professional contractor - installation or repairs performed by any other party shall void
the warranty. This warranty shall not apply to breakage or damages caused by normal wear and tear, fault, carelessness, abuse, misuse, misapplication,
improper maintenance, alteration or modication of the unit, as well as chemical or natural corrosion, accident, re, ood, act of God or any other casu-
alty. Improper care and cleaning will void the warranty. Use of cleaners containing abrasive cleansers, ammonia, bleach, acids, waxes, alcohol, solvents
or other products not recommended for chrome or similar nish, glass or acrylic will void the warranty. For additional product maintenance instructions
please refer to product installation manual. DreamLine™ is not responsible for any issues arising in connection with errors or omissions in information
provided on DreamLine’s websites. The warranty does not extend to any non-DreamLine™ plumbing or components installed by installers, end users
or by any party other than DreamLine™.
THE FOREGOING WARRANTIES ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING BUT NOT
LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. BATH AIU-
THORITY LLC (“DREAMLINE”) AND/OR SELLER DISCLAIM ALL LIABILITY FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES. DREAMLINE™ IS NOT LIABLE FOR PERSONAL INJURIES OR DEATH TO ANY PERSON OR FOR ANY DIRECT,
SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGE, LOSS OF USE, LOSS OF TIME, LOSS OF PROFITS, INCONVENIENCE,
INCIDENTAL EXPENSES, LABOR OR MATERIAL CHARGES, OR ANY OTHER COSTS RESULTING FROM THE USE OF ITS
PRODUCTS OR PERTAINING TO THE APPLICATION OF THE PRESENT WARRANTY, OR RESULTING FROM THE REMOVAL OR
REPLACEMENT OF ANY PRODUCT OR ELEMENT OR PART COVERED BY THIS WARRANTY.
DreamLine™ is not responsible for product code compliance or for verifying building code restrictions on installation or use and any such compliance is
excluded from this warranty. DreamLine™ reserves the right to modify this warranty at any time - such warranty modication will not alter warranty ap-
plicable at the time of sale of the products in question. The warranty terms for specic products are:
SHOWER & TUB DOORS, SHOWER ENCLOSURES AND SHOWER BASES
DreamLine™ warrants shower & tub doors, shower enclosures and shower bases to be free from defects in workmanship and materials under
normal residential use for a period of ve (5) years from the initial date of purchase by the owner/end-user, contractor or builder from an authorized dealer.
SHOWER CABINS (JETTED & STEAM)
DreamLine™ warrants glass, acrylic and nish to be free from defects in workmanship for a period of ve (5) years from initial date of purchase by
the owner/end-user, contractor or builder from an authorized dealer; and plumbing, electrical and steam generator components for a period of
one (1) year from the initial date of purchase by the owner/end-user, contractor or builder from an authorized dealer.
SHOWER COLUMNS
DreamLine™ warrants shower columns to be free from defects in workmanship and materials under normal residential use for a period of one
(1) year from the initial date of purchase by the owner/end-user, contractor or builder from an authorized dealer.
VANITIES AND VESSEL SINKS
DreamLine™ warrants bathroom vanities and vessel sinks to be free from defects in workmanship and materials under normal residential use
for a period of one (1) year from the initial date of purchase by the owner/end-user, contractor or builder from an authorized dealer.
Some states/provinces do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of special, incidental or consequential
damages, so these limitations and exclusions may not apply to you. This warranty gives you specic legal rights. You may also have other rights, which
vary from state/province to state/province.
WARRANTY