DRIFT HD User manual

Instore "130"you
canfind and buy almostall necessarygoodsforyourauto
in
Kyiv and othercities,deliveryby ground andpostal services. Ourexperienced
consultantswill provide youwithexhaustive informationand helpyoutochose
the very particular thing.We arewaiting foryou at the address
http://130.com.ua
PHONES
(044) 360-7-130
(050) 336-0-130
(063) 788-0-130
(067) 233-0-130
(068) 282
-
0
-
130
Internet storeof
autogoods
CARRECEIVERS —Receivers •Mediareceiversandstations•Nativereceivers •CD/DVD changers •FM-modulators/USBadapters•Flashmemory•Faciaplates and adapters •Antennas •Accessories |
CARAUDIO —Car audiospeakers •Amplifiers•Subwoofers •Processors•Crossovers •Headphones•Accessories|TRIPCOMPUTERS —Universalcomputers •Modelcomputers •Accessories|
GPSNAVIGATORS —PortableGPS•Built-in GPS•GPSmodules •GPStrackers •Antennas forGPSnavigators•Accessories|VIDEO —DVR •TVsetsand monitors•Car TVtuners•Cameras •Videomodules
•Transcoders •Car TVantennas•Accessories|SECURITYSYSTEMS —Car alarms •Bikealarms •Mechanicalblockers •Immobilizers •Sensors •Accessories |OPTICANDLIGHT —Xenon•Bixenon •Lamps
•LED •Stroboscopes •OpticandHeadlights •Washers •Light,rainsensors •Accessories |PARKTRONICS ANDMIRRORS —Rear parktronics•Frontparktronics •Combined parktronics •Rear-viewmirrors
•Accessories |HEATINGANDCOOLING —Seat heaters •Mirrorsheaters •Screen-wipers heaters •Engineheaters •Auto-refrigerators •Airconditioningunits •Accessories |TUNING —Vibro-isolation
•Noise-isolation •Tintfilms •Accessories |ACCESSORIES —Radar-detectors•Handsfree,Bluetooth•Windowlifters•Compressors •Beeps,loudspeakers •Measuring instruments •Cleaners •Carsits
•Miscellaneous|MOUNTING —Installationkits •Upholstery•Grilles•Tubes•Cableand wire •Tools•Miscellaneous|POWER —Batteries •Converters •Start-chargingequipment•Capacitors
•Accessories |MARINE AUDIOANDELECTRONICS —Marinereceivers•Marineaudiospeakers •Marinesubwoofers •Marineamplifiers•Accessories |CARCARE PRODUCTS —Additives •Washer fluid •
Care accessories •Car polish •Flavors •Adhesives andsealants |LIQUIDANDOIL —Motoroil•Transmissionoil •Brakefluid •Antifreeze•Technicallubricant
ICQ
294-0-130
597-0-130
SKYPE
km-130

user manual
130.com.ua
Autogood products «130»

4
contents
Quick Start 5
Overview 7
Precautions
a) General Precautions 8
b) Weather Resistance 8
Mounting the Camera 9
Preparing for Use
a) Battery Installation
• Installing the Camera Battery 11
• Changing the Remote Control Battery 11
b) Powering on and Charging
• Turning the Camera On 11
• Turning the Camera O 11
• Charging the Battery 11
• Battery Life 12
c) Camera Lens Rotation
• Rotating the Lens 12
d) Using the SD Card
• Inserting and Removing the SD Card 13
• Formatting the SD Card 13
• Recording Time 13
Using the Camera
a) Changing the Record Mode 15
b) Video Mode
• Recording Video 15
c) Photo Mode
• Taking Photos 15
d) Time Lapse Mode
• Taking Time-Lapse Photos 16
• Changing the Sequence Interval 16
e) Zoom 16
Using the Remote
a) Basic Remote Use
• Using the Remote Control 17
b) Remote Pairing
• To Cancel a Remote Pairing 17
• Pairing the Remote Control 18
• Pairing Multiple Cameras to a Single Remote 18
Conserving Battery Life 19
Camera Care 20
Menu Options
a) Main Menu
• Opening the Sub-Menus 21
b) Video Menu
• Video Playback 21
• Deleting Videos 21
c) Photo Menu
• Viewing Photos 21
• Slideshow Function 21
• Deleting Photos 22
d) Video Conguration Menu 22
e) Setup Menu 23
f) Setting the Time & Date 24
Connecting the Camera to a Computer or TV
a) Connecting the Camera to a Computer 25
• Connecting to a Windows PC 25
• Connecting to a Mac 25
b) Playing and editing video footage on a Computer 26
c) Connecting the Camera to a TV 26
Replacing the Lens 27
FAQ 30
Computer System Requirements 31
Troubleshooting 32
Technical Specication 33
Further Help 34
Warranty 36
130.com.ua
Autogood products «130»

65
quick start
We have carefully designed the Drift HD package as an all-in-one solution, allowing
you to shoot in virtually any situation without having to purchase extra equipment
apart from a micro SD card. We want you to be able to start using your camera as
soon as possible. This section contains the basic information you need right away.
The Drift HD has many more features than these described here – please refer to later
sections for more information.
Getting ready to use the camera
Please unscrew the rear hatch of the camera (anti-clockwise movement). Then, gently
insert the battery (more details on page 11) and a micro SD memory card (more details
on page 15) as illustrated below. Securely screw the rear hatch back to its original
position (clockwise movement).
Securely mount the camera. The LCD screen’s live preview allows for accurate
positioning to get the best possible shot. A full description of the various mounting
options can be found on pages 9-10. Do not forget the lens of your camera can be
rotated!
Turning the camera on
Press the SELECT button to turn the camera on. The LCD screen will turn on and the
LED in the SELECT button will turn green. Once switched on, the Drift logo will appear
and the camera will enter the Live Preview mode. In Live Preview Mode, the screen
will display a live image from the camera lens, and a number of icons indicating the
recording options, remaining memory and battery life – an overview of these can be
found on page 18. To turn your camera o, press and hold the Select button for 3
seconds.
Note: The rechargeable battery will need
to be fully charged before its first use.
Please see page 12 for details on how to
proceed in order to charge the battery.
Recording Video
1. To begin recording, press the SELECT button on the camera or the RECORD button
on the remote control. The unit will beep and the LED will turn red.
2. To stop recording, press the SELECT button again, or the STOP button on the
remote. There will be another beep and the LED will turn green.
Capturing Photos
The default recording mode for the camera is Video mode. In order to take photos, the
Photo mode must be selected. Changing the Record Mode is described on page 17.
1. Once the Record Mode has been changed to Photo, return to Live Preview mode by
pressing the MENU button a few times.
2. Use the LCD screen to aim the camera at your subject.
3. Press the SELECT button on the camera or the RECORD button on the remote
control. The unit will beep once and the LED will briey turn red.
4. Once the LED returns to green, the camera is ready to take another photo.
Reviewing Photos and Video
To change any of the camera settings or review / play back videos or photos recorded
with the Drift HD, press the MENU button on the camera. This will bring up the Main
Menu: If the memory card contains any videos or photos taken with the Drift HD,
these will be indicated by a number on the Video or Photo icons. Using the UP and
DOWN buttons, highlight the Video icon or the Photo icon and press the SELECT
button. You can now browse your les using the UP and DOWN buttons. Full details
about the Video & Photo Menus can be found on pages 28-29.
Note: You will need to change the record
mode back to video to be able to record
video again.
130.com.ua
Autogood products «130»

7 8
Rear Hatch
1.5" LCD Screen
UP Button
DOWN Button
MENU Button
Rotatable Lens
SELECT Button
Microphone Input
AV HDMI Output ¼" Camera Thread
Micro SD Card Slot
USB Port
Speaker
Battery Slot
precautions
A GENERAL PRECAUTIONS
Please take note of the following guidelines when using your Drift HD:
• The camera is shock resistant, but not shock proof.
• For your safety, do not press the buttons on the camera body during sports
activities.
• Do not place the camera in areas prone to dust or damp for extended periods of
time.
• Do not leave the camera in places exposed to extremely high temperatures, such
as under direct sunlight, for extended periods of time. This may aect the camera
housing and internal components.
• Clean the lens with a soft cloth to remove ngerprints or dust. Please do not use
chemicals.
• The camera has a working temperature range of -10°C to 40°C (50 to 104 F)
• Turn the camera o before removing the batteries or memory card. The card and
data may be damaged if the memory card is inserted or removed while the camera
is switched on.
• Remove the batteries and memory card before storing the camera for long periods
of time.
B WEATHER RESISTANCE
The Drift HD action camera is fully splash-proof and weatherproof, but it is not
designed to be used in a water environment. Please be aware of this when using your
Drift HD. The camera was designed to withstand dust, snow, rain, splashes and even
an accidental quick submersion; however it was not designed to stay submerged
while not in its waterproof case. Drift Innovation will not assume any responsibility for
camera malfunction caused by liquid entering the camera as a result of misuse by the
user.
• Liquid may get inside the camera if the hatch is not installed properly, or if a non-
waterproof hatch is used. Always ensure that the hatch you’re employing is securely
locked.
• If the camera gets wet, wipe the liquid o as soon as possible with a dry cloth.
• Other camera accessories may not be waterproof – please read their instructions
carefully.
• The in-built microphone is covered with a rubber seal as shown on the opposite
page – this is not to be removed, changed or punctured in any way, or the camera
will no longer be waterproof, and your warranty will be void.
Attention:
• Rechargeable batteries are only to be
charged under adult supervision.
• The battery terminals are not to be
short-circuited.
• Do not open, puncture or otherwise
damage the Lithium-Ion battery, or
dispose of it in fire.
Disclaimer:
Drift Innovation will not, under any
circumstances, be responsible for injuries
or property damage incurred during
participation of any high-risk sport/
activity not endorsed or recommended
by Drift Innovation. Remember that the
warranty will only cover manufacturing
defects.
overview
130.com.ua
Autogood products «130»

910
mounting the camera
The Drift HD can be mounted in a dierent number of ways using the mounts
provided:
Fixing the Camera onto the Universal Clip
1. Align the screw of the universal clip with the thread on the underside of the camera
body.
2. Twist the screw thread in a clockwise direction.
3. As the universal clip tightens against the body of the camera, rotate the universal
clip to provide the desired angle of attachment.
4. Tighten the screw on the universal clip until the clip ts rmly against the camera
body.
Mounting the Camera on a Goggle Mount
1. Attach the goggle mount to the strap of your goggle.
2. Slide the camera (with universal clip attached) into the goggle mount until the two
arms on the clip ‘click’ into place.
Mounting the Camera on a Helmet
1. Position the helmet mount against your helmet to nd the optimum mounting
position.
2. Ensure the surface you wish to attach the helmet mount to is clean, dry and free of
oil and dust. Attach the remaining velcro strip onto the helmet.
3. Adhere the mount to the helmet using the 3M VHB adhesive provided. Allow 24
hours to cure.
4.Slide the camera (with universal clip attached) into the helmet mount until the two
arms on the clip ‘click’ into place.
Mounting the Camera on a Vented Cycle- or Kayak Helmet
1. Position the helmet mount on the top or side of your helmet to nd the optimum
mounting position.
2. Thread the velcro strap through the slits in the helmet mount to attach it to the
helmet.
3. Slide the camera (with universal clip attached) into the helmet mount until the two
arms on the clip ‘click’ into place.
Mounting the Camera onto a Tripod, Monopod or Suction Cup Mount
1. The camera has a standard tripod thread (1/4”-20) embedded into the camera body.
This is the same thread as the one used to attach the universal clip, and used in
nearly every camera accessory available.
2. Thread the camera onto a tripod, camera mount or suction mount (not included), or
any other mount with a standard camera thread.
Tips on Mounting the Camera:
• Great video footage generally features
another person or object. In skiing or
snowboarding this could be the skier in
front, or your own skis. In motorsports,
this can be the fairing of a bike or a car
bonnet. If your object is moving too,
like a wheel or bike pedals, so much
the better. Experiment to find the most
exciting shots.
• Your camera doesn’t necessarily
have to face forward. A classic POV
video technique is the direct user
shot. For example in mountain biking,
try mounting the camera on the
handlebars and pointing it back at the
user - It makes for some great action
footage.
• If your activity allows, mount the
camera in dierent positions between
shots. Then, when editing your video
later you can cut between various
angles to make something truly
special. Some pros use more than one
camera so they can shoot multiple
angles at the same time.
• The lens of the Drift HD can be rotated
to help you align your shots. Please
refer to the lens rotation section on
page 12 for further information.
! However you choose to mount your
camera, ensure that the camera is tted
firmly to reduce the risk of losing it. Give
it a tug before you set out, just to make
sure.
130.com.ua
Autogood products «130»

11 12
preparing for use
A BATTERY INSTALLATION
Installing the Camera Battery
1. Please unscrew the rear hatch of the camera (anti-clockwise movement).
2. Holding the camera with the LCD screen facing down, insert the battery with the
label facing upwards and the arrow pointing into the slot. Once gently pushed in all
the way, the battery will lock into place.
3. Screw the rear hatch of the camera (clockwise movement) back to its original
position.
4. To remove the battery if needed, push down the lever holding the battery in place.
The battery is spring loaded, and will slide out promptly.
Changing the Remote Control Battery
The remote control is supplied with a battery already installed, and is ready to use out
of the box. If the remote stops working, this battery can be replaced.
1. Using a small screwdriver, remove the four screws xing the remote control battery
cover.
2. Carefully remove the battery and replace it (model CR2032, presented as a coin).
3. Replace the remote control battery cover and the four screws.
B POWERING ON & CHARGING
Turning the Camera On
Press the SELECT button. The LCD screen will turn on and the LED will turn green. The
LCD screen will show the Drift logo, and the camera will enter Live Preview mode.
Turning the Camera O
To turn the camera o, press and hold the SELECT button for 3 seconds.
Note: The camera can be set to turn o automatically in order to conserve battery
power (page 19).
Charging the Battery
The Drift HD comes with a rechargeable Lithium-Ion battery which can be charged
with the included USB cable. Socket-to-USB adaptors can be used as well.
1. Ensure the battery is in the camera and the unit is powered o.
2. Insert the smaller end of the USB cable into the USB mini slot inside the camera.
3. Attach the other end of the USB cable to a USB port in your computer, or to a USB
power adapter (not included).
4. If charging via a computer, the LED will turn blue and the screen will go black. If
charging via a USB power adapter or a USB cigarette lighter adapter, the camera will
switch on.
5. To charge the camera, press and hold the SELECT button for 3 seconds. The screen
will turn o and the LED will turn blue, to indicate charging is in progress.
Note: Remove the battery if the camera
is not going to be used for an extended
period of time.
Note: Take care not to damage the
waterproof seal when replacing the
remote battery.
Note: The camera will switch on
automatically when it is connected to an
external power source.
6. Once the camera is fully charged, the LED will turn o. Remove the USB cable and
close the rear hatch. It takes around 2½ hours to be battery to be fully charged.
Note: If the LED is does not turn blue, the battery is not charging. Please follow the
above instructions carefully to ensure that the LED turns blue and the battery does
actually charge.
Note: When charging the camera with a USB cable via a Mac, you may get an error
message about an incorrectly removed external device. This is not a problem and can
be safely ignored.
Note: The battery needs to be fully charged before its rst use.
Battery Life
At a temperature of 25°C (77 F), with all power-saving features switched o, with the
LCD switched on and the camera recording continuously, the battery will last for
about 3 hours on a full charge.
In very cold conditions like -5°C (23 F), with all power-saving features switched o,
the LCD switched on and the camera recording continuously, the battery will last for
about 2.5 hours on a full charge.
Note: Please see the Conserving Battery Life section on page 19 for details on how to
make the battery last longer.
Using an external power supply
The Drift HD can be powered by an external power supply such as a USB power
adapter, a battery kit or a cigarette lighter adapter. We do recommend you to power
o your camera before plugging your camera to any external power supply.
Note: Plugging an external power supply into the camera does not recharge the
battery unless you put the camera into charging mode (page 11). The battery will not
charge when the camera is switched on.
If the external power is cut o during recording (e.g. if the cigarette lighter adapter
comes loose), the camera will immediately start drawing power from the rechargeable
battery instead and continue recording, protecting your footage from le corruption.
Note: This feature will only work if the battery is charged. If using your camera with
an external power supply, we recommend charging the battery beforehand to ensure
your files are protected.
C CAMERA LENS ROTATION
A unique feature of the Drift HD is the rotating camera lens. In order to maximise your
mounting options, the lens can rotate through a total of 300°, allowing for an upright
image from even the most awkward positions.
Rotating the Lens
Whilst holding the camera body in one hand, use your index nger and thumb of your
other hand to grab the camera lens rmly. Twist the camera lens to the desired angle.
! When the low battery warning appears,
please recharge the battery. If the battery
runs out while recording video, the data
on the card may become corrupted. In
most situations, the camera will close the
video le and power o automatically,
but we cannot guarantee that the
footage on the card will not be lost
during an abrupt interruption of power.
! The camera lens cannot be rotated
through 360° – it can only be rotated
through a range of 300°. At either end of
this range, there is a hard stop. Do not
force the camera rotation past this point,
as you risk damaging the components. If
excess resistance is experienced, double-
check that you have not reached the
camera rotation stop.
! The camera is weatherproof and this
is not aected by the rotation of the
camera lens. However, do not rotate the
lens while the camera is wet or covered
in mud, as this may force liquid into the
body of the camera and damage the
components.
130.com.ua
Autogood products «130»

13 14
D USING THE MICRO SD CARD
The Drift HD can take micro SD / SDHC cards of up to 32GB in size.
Inserting and Removing the Micro SD Card
1. Turn the camera o.
2. Remove the rear hatch, unscrewing it (anti-clockwise movement).
3. Insert the Micro SD card into the memory card slot, ensuring that the card’s
terminals are facing up. Carefully push it all the way in until it clicks into place.
5. Screw the rear hatch of the camera (clockwise movement) back to its original
position.
4. To remove the SD card if needed, push the card until it clicks and then pull the card
out.
Note: The Drift HD cannot record any video or photo les without a memory card
Formatting the Micro SD Card
It is possible to delete all the data on a memory card by formatting it. When using a
new memory card for the rst time, formatting it is recommended.
1. Press the MENU button to open the Main Menu.
2. Highlight the Setup icon and press the SELECT button.
3. Highlight the Format option on the Setup Menu and press the SELECT button.
4.Confirm that you want to format the card by highlighting the tick icon and pressing
SELECT button. The formatting process will take several seconds. Please be patient
during this process.
Note: Formatting the Micro SD card does not delete your custom preferences such as
resolution, menu language, FPS or screen brightness.
Note: The recording times in the table below are an approximation. Actual recording
times for Micro SD cards will vary depending on the recording conditions.
Approximate Recording Time
1080p HD 720p HD WVGA (SD)
1 GB 10 mins 17 mins 26 mins
2 GB 21 mins 34 mins 52 mins
4 GB 42 mins 1h 08 mins 1h 44 mins
8 GB 1h 24 mins 2h 17 mins 3h 28 mins
16 GB 2h 48 mins 4h 34 mins 6h 56 mins
32 GB 5h 35 mins 9h 08 mins 13h 53 mins
! Ensure that the camera is powered o
when inserting and removing a memory
card. The card and the data may be
damaged if inserted or removed while
the camera is turned on.
! Once the card is formatted, this cannot
be undone. Ensure any files you wish
to keep have been copied onto your
computer, as all data on the SD card will
be lost once formatted.
preparing for use
130.com.ua
Autogood products «130»

15 16
using the camera
A CHANGING THE RECORD MODE
In order to switch between recording video and shooting photos, you will need to
change the camera Record Mode in the Video Configuration Menu.
1. Press the MENU button to open the Main Menu.
2. Use the UP and DOWN buttons to highlight the Video Conguration icon, and press
the SELECT button.
3. The screen will show a list of settings. Highlight the Record Mode option and press
the SELECT button.
4. Highlight the icon of the Record Mode you wish to use and press the SELECT button
again.
5. Press the MENU button twice to return to Live Preview mode.
Note: The camera must be in Live Preview mode to record any video or take any
photos. The MENU button also functions as a BACK button. Press the MENU button a
few times to return to Live Preview mode.
B VIDEO MODE
When the camera is in Video mode, the screen will display a live preview image from
the camera lens and a number of icons indicating the camera’s status.
Recording Video
1. Ensure that the camera has been set to Video Mode using the Video Conguration
menu.
2. To start recording, press the SELECT button on the camera or the RECORD button
on the remote control. The unit will beep and the LED will turn red.
3. To stop recording, press the SELECT button again, or the STOP button on the
remote. There will be another beep and the LED will return to green.
Note: If the SD card runs out of space while recording, the camera will stop recording
but it will remain switched on. You will need to turn it o yourself unless Camera
Auto-O has been enabled (page 19).
Note: If the video being recorded is very long, the video le will be separated into
multiple les every 3.6 GB (i.e. every 40 minutes in 1080p). This is automatic – you do
not need to monitor this process. The camera will resume lming after a few seconds,
once the file is saved. Please be patient while the file is saving.
B) PHOTO MODE
When the camera is in Photo mode, the screen will also display a live preview image,
but the camera status icons are slightly dierent.
Taking Photos
1. Ensure that the camera has been set to Photo mode using the Video Conguration
menu.
Record Mode
Video Configuration
1/2
Resolution: 1080P
Frame Rate: 30
Exposure: 0.0
Outdoor / Indoor
Video Configuration 1/2
Resolution: 1080P
Frame Rate: 30
Exposure: 0.0
Outdoor / Indoor
00.00.02
Mode Indicator
Recording Indicator
Remaining Memory
Remaining Battery
2. Press the SELECT button on the camera or the RECORD button on the remote
control. The unit will beep once and the LED will briey turn red.
3. Once the LED returns to green, the camera is ready to take another photo.
D TIMELAPSE MODE
Taking Time-Lapse Photos
The Drift HD includes a time lapse mode. When activated, the camera will take a
photo every few seconds until it is stopped or the memory card is full.
1. Ensure that the camera has been set to Time Lapse mode using the Video
Configuration menu.
2. Press the SELECT button on the camera or the RECORD button on the remote
control. The unit will beep once and the LED will briey turn red.
3. The camera will take photos every 3 seconds by default.
Note: You can change the time interval between time-lapse photos by modifying the
Sequence Interval setting as described below.
Changing the Sequence Interval
1. Press the MENU button to open the Main Menu.
2. Use the UP and DOWN buttons to highlight the Video Conguration icon, and press
the SELECT button.
3. The screen will show a list of settings. Highlight the Sequence Interval option and
press the SELECT button.
4.Use the UP and DOWN arrows to choose the desired time interval and press the
SELECT button to conrm.
Note: The Sequence Interval setting can only be changed when the record mode is
set to Time-Lapse. The available Sequence Interval settings are 3 seconds, 5 seconds,
10 seconds and 30 seconds.
E ZOOM
The Drift HD includes a digital zoom function that allows you to take close-up photos
and videos. To use it, press and hold the UP arrow to zoom in, and the DOWN arrow
to zoom out.
Note: You can zoom in and out while video recording is in progress
Note: The zoom indicator bar may disappear when it is not in use.
Note: Please be aware that using the digital zoom may aect the image quality of your
recording.
Shots RemainingRemaining Battery
Zoom Indicator
130.com.ua
Autogood products «130»

17 18
using the remote
A BASIC REMOTE USE
The Drift HD comes with a wireless RF (radio frequency) remote control to allow easy,
hands-free operation of the camera. It can be used both to record video and to take
photos.
Note: Always make sure you fasten the remote control tightly and securely so you do
not lose it.
Using the Remote Control
1. Ensure that the remote control has been enabled. If in doubt, open the Main Menu,
highlight the Setup menu and press SELECT. There should be a tick by the Remote
Control setting on the first page of the Setup Menu.
2. Attach the remote control to your wrist, handlebar or jacket using the short velcro
strap.
3. With the camera in Live Preview Mode, press the RECORD button on the remote to
start recording or to take a photo. If the camera speaker is switched on, there will be
a beep.
4. If the camera is in Video Mode, press the remote control’s STOP button to stop
recording. If the speaker is switched on, the camera will beep again.
Note: The remote control will not operate the camera if the camera is switched o.
B REMOTE PAIRING
The Remote Pairing function links your camera to a specic remote. If unpaired, the
camera will work with any Drift HD remote control in range. This can cause problems
if more than one person is using a remote at the same time. For example, if your
friend presses his remote’s STOP button, your recording will also stop, whether you
want it to or not. Pairing your remote to your camera will prevent this from happening
– your camera will only respond to instructions from your remote.
Your Drift HD remote is paired with your camera out of the box, so you do not need to
pair it again. If you lose or damage your remote however, you will need to cancel the
old pairing and pair the replacement remote with your camera.
To Cancel a Remote Pairing
1. Open the Setup Menu, highlight the Remote Pairing option and press the SELECT
button.
2. Highlight the Reset icon (the red “X”) and press the SELECT button.
3. The Remote Pairing is now deleted. The icon next to the Remote Pairing option will
change into a red cross to indicate the remote is no longer paired.
Pairing the Remote Control to your camera
1. Press the MENU button to open the Main Menu.
2. Highlight the Setup icon, and press the SELECT button.
3. Highlight the Remote Pairing option on the rst page of the Setup Menu and press
the SELECT button.
4. Press the RECORD Button on the Remote. The camera will beep if the remote is
recognized.
5. The icon next to the Remote Pairing option will change to indicate the pairing (two
white arrows).
Pairing Multiple Cameras to a Single Remote
It is possible to pair multiple cameras with a single remote. This allows them all
to be operated with one button press, but prevents other Drift HD remotes from
interrupting your recording.
For every camera you wish to pair:
1. Press the MENU button to open the Main Menu.
2. Highlight the Setup icon, and press the SELECT button.
3. Highlight the Remote Pairing option on the rst page of the Setup Menu and press
the SELECT button. Leave the camera this way.
Once every camera to be paired is displaying the screen above:
4.Press the RECORD Button on the Remote. Each camera will beep if the remote
is recognized. Any camera that does not beep and return to the Setup menu
automatically will not be paired – try pressing the RECORD Button again if this
happens.
5. The icon next to the Remote Pairing option will change to indicate the pairing – in
every camera (two white arrows).
! When pairing multiple remotes, always test the remote to see if it operates all the
cameras before mounting them. You don’t want to nd out later that one of your
cameras didn’t start recording.
STOP ButtonRECORD Button
130.com.ua
Autogood products «130»

19 20
conserving battery life
The Drift HD comes with a rechargeable 1100mAh Lithium-Ion battery, allowing you
to record continuously for hours between charges. However, sometimes you may nd
yourself in a location without a power outlet to charge your camera with. Also, cold
conditions drain battery power at a faster rate. Fortunately, the Drift HD comes with
a number of features to extend the battery life. These can all be found in the Setup
Menu.
Note: Changing camera settings is described in the Setup Menu section on page 23-24.
LCD O
The Drift HD’s built-in LCD screen consumes power, so one of the best ways to
extend your battery life is to use the LCD Auto-O function. By default this LCD
screen is always on, but it can be set to turn o when no buttons are pressed for a
while (the exact time interval is chosen when turning this function on). The camera
will still function as normal when the screen is switched o – in Live Preview mode,
the camera is ready to record at any time, and if recording is in progress, it will
continue to record with the screen o. The LCD remote is also useable with the
screen o. The screen can be turned on again by pressing any button.
Note: Do not use the Select button to switch the camera screen back on – doing
so will begin a new recording or stop the current recording if the camera is in Live
Preview mode. Unless you specically want to start or stop a recording, use one of the
other buttons.
Changing the Brightness Setting
The LCD backlight also consumes power. If you don’t want to switch the LCD screen
o, it is possible to reduce its intensity by using the LCD Brightness setting on the
second page of the Setup menu. You may notice a slight increase in battery life if you
use a lower brightness setting.
Camera Auto-O
It is also possible to set the camera to switch o entirely when no buttons are pressed
for a set amount of time (the exact time interval is chosen when turning this function
on). The main use of this function is to automatically switch o the camera in case
you forget to do so yourself.
Note: This will not switch the camera o while recording is in progress. However,
when the camera does switch o, you will need to switch it back on again before you
can record any new video.
Note: The remote control will not operate the camera if the camera is switched o.
Spare batteries
If the battery life of the Drift HD is not long enough for your purposes, you can charge
a second battery before you set out and then change it when the first one runs out.
Spare 1100mAh batteries and external PowerPacks are available from the Drift dealers.
Please visit our ocial website http://www.driftinnovation.com/ for more information
regarding batteries and accessories.
! Always change the battery in a clean,
dry and safe environment. Getting
camera batteries wet will damage them
and may result in injury to yourself. For
your safety, never use damaged batteries.
camera care
The Drift HD is specically designed for extreme sports. It is a very durable piece of
equipment. However, to ensure a long and healthy life for your camera, please follow
the instructions below.
Cleaning the Camera
During your sporting activities, the camera will inevitably get dirty or wet. Although
this is not an issue, it is recommended that you clean the Drift HD whenever this
occurs. Clean the camera thoroughly with a damp cloth and let it air dry before you
open the back hatch or rotate the lens. Take extra care when cleaning sensitive areas,
such as the built-in microphone or the internal speaker.
Cleaning the lens and LCD screen
In order to provide a clear image for high denition video, it is important to keep the
camera lens clean. Be careful not to scratch the camera lens whilst cleaning it. Wipe
o any surface mud or water from the lens with a damp cloth and use a dry scratch-
proof cloth to polish the lens once it is dry.
Cleaning the seals
To ensure that the camera remains weatherproof and water resistant, it may be
necessary to occasionally clean the contact surfaces around the rear camera hatch
seal. This can be done by wiping a damp cloth around the seal. Be careful not to leave
excessive water on the seal, and let it air dry.
! Scratch-proof cloths are available from
any camera shop or optician.
!You can run a little Vaseline around the
rubber seal from time to time to keep the
seal airtight.
130.com.ua
Autogood products «130»

21 22
menu options
A THE MAIN MENU
To open the Menu, press the MENU button when the camera is switched on. A screen
containing the four Menu icons will appear:
If the Micro SD Memory card contains any Video or Photo les, the number of each
will be indicated beside the Video and Photo menus icons.
Opening the Sub-Menus
1. Once the Main Menu is open, use the UP and DOWN buttons to highlight the icon
of the menu option you wish to open.
2. Press the SELECT button.
B VIDEO MENU
Once you have selected the Video Menu, you will either see the ‘No File’ screen, or
you will see a thumbnail image of the last video file recorded to the Micro SD card.
Video Playback
1. Scroll through the thumbnail images using the UP and DOWN arrows.
2. Once you nd the video you want to watch, press the SELECT button.
3. A screen with three options will appear - highlight the View option and press the
SELECT button. The video will start playing.
4. Press the SELECT button to pause and resume playback, or the MENU button to exit.
Deleting Videos
1. Scroll through the thumbnail images using the UP and DOWN arrows.
2. Once you nd the video you want to delete, press the SELECT button .
3. A screen with three options will appear – highlight the Delete option and press the
SELECT button.
4. Conrm le deletion by highlighting the tick icon and pressing the SELECT button.
C PHOTO MENU
Once you have selected the Photo Menu, you will either see the ‘No File’ screen, or
you will see a thumbnail image of the last photo saved to the Micro SD card.
Viewing Photos
1. Scroll through the thumbnail images using the UP and DOWN arrows.
2. Press the MENU button to exit.
Slideshow Function
1. Scroll through the thumbnail images using the UP and DOWN arrows.
2. Once you nd the image you want to show rst, press the SELECT button.
3. A screen with three options will appear – highlight the View option and press the
SELECT button. The camera will show all the photos on the card in order, changing
image every few seconds.
4. Press the SELECT button to pause the slideshow, and press it again to resume it.
Note: The MENU button also functions
as a BACK button. Pressing the MENU
button while in a sub-menu will take
you back to the Main Menu. Pressing the
MENU button on the Main Menu will take
you back to Live Preview mode.
! You can Fast Forward and Rewind a
video while it is playing. Press the DOWN
arrow to fast forward, and the UP arrow
to rewind. Once you reach your desired
point in the le, press the SELECT/Play
button to pause the video. Press the
SELECT/Play button to resume playback.
Note: You can delete all the videos on
the camera by selecting the Delete All
option. This will not delete any of the
photo files on the SD card.
!Use the slideshow function when the
camera is connected to a television to
view all your photos on a big screen.
Deleting Photos
1. Scroll through the thumbnail images using the UP and DOWN arrows.
2. Once you nd the video you want to delete, press the SELECT button.
3. A screen with three options will appear – highlight the Delete option and press the
SELECT button.
4. Conrm le deletion by highlighting the tick icon and pressing the SELECT button.
D VIDEO CONFIGURATION MENU
To change Video Conguration settings, highlight the setting you wish to change and
press the SELECT button. Use the UP and DOWN arrows to choose the option you
want, and press the SELECT button again to conrm it. The icon next to the setting
name will reect the new setting.
Note: The options available depend on the recording mode selected – the Resolution
option is only available in Video mode, and the Sequence Interval option is only
available in Time Lapse mode.
Setting Options Description
Record Mode 1. Video (Default)
2. Photo
3. Time Lapse
Choose whether to record video, still photos or time-lapse photos.
Resolution 4. 1080p HD
5. 729p HD (Default)
6. WVGA (SD)
Dierent video qualities can be selected to optimise the video quality or le size.
1080p requires the most memory but has the best video quality.
Exposure 7. -2.0
8. -1.0
9. 0 (Default)
10. +1.0
11. +2.0
(Advanced Users) The exposure setting determines the camera’s sensitivity to light. If
conditions are very bright (eg. sun on snow), use a negative value. For dark conditions
(eg. dusk), use a positive value. Most of the time you can just use zero.
Outdoor / Indoor 12. Outdoor
13. Indoor
Sequence Interval 14. 3 seconds (Default)
15. 5 seconds
16. 10 seconds
17. 30 seconds
Allows the user to select the time interval between photos when shooting in Time-
Lapse mode.
!You can delete all the photos on the
camera by selecting the Delete All
option. This will deleted only the photos,
and will not aect any of the video les
on the micro SD card.
! Once a le is deleted, it cannot be
restored. Make sure you no longer need
a video before deleting it. Please be
especially careful when using the Delete
All option.
# Video Files
Video Menu
Video Configuration
# Photo Files
Photo Menu
Setup Menu
00.00.32
0001/0004
File Number
Video Length
Total Video Files
Remaining Battery
130.com.ua
Autogood products «130»

E SETUP MENU
To change Camera Setup settings, highlight the setting you wish to change and press
the SELECT button. Use the UP and DOWN arrows to choose the option you want,
and press the SELECT button again to conrm it. The icon next to the setting name
will reect the new setting.
Menu Options Description
Mic Sensitivity 1. High
2. Medium (Default)
3. Low
4. O
Dierent sports have dierent ambient sound levels. Generally choose Low for
motorsports and Medium for cycling and wintersports.
Remote Control 5. Yes (Default)
6. No
Use this option to turn remote control functionality on or o.
Remote Pairing 7. Paired (Default)
8.Not Paired
This options allows for the camera to be paired with a specic remote. Please see the
pairing instructions in page 18.
LCD O 9. Never (Default)
10. 5 seconds
11. 10 seconds
12. 20 seconds
13. 1 minutes
14. 5 minutes
To conserve battery life, the LCD screen can be set to power down after a set period
of time. The camera remains on - only the LCD screen powers down. To switch on the
LCD screen, just press any button on the control panel.
Camera O 15. Never (Default)
16. 1 minutes
17. 5 minutes
18. 10 minutes
19. 20 minutes
20. 30 minutes
To conserve battery life, the whole camera can be set to power down after a set period
when not in use. Once powered down, the camera will need to be switched on again.
The camera will not switch o while recording is in progress.
Speaker Volume 21. O
22. Low
23. Medium
24. High (Default)
Use this option to change the volume level of the built-in speaker.
LCD Brightness 25. High (Default)
26. Medium
27. Low
Use this option to change the brightness of the built-in LCD screen.
Date 28. Year
29. Month
30. Day
Set the camera date. When the battery is removed or runs out of charge, the date
information is lost and will need to be reset.
Time 31. HH
32. MM
Set the camera time. When the battery is removed or runs out of charge, the time
information is lost and will need to be reset.
Date/Time
Stamp
33. O (Default)
34. On
Certain video applications require a date/time stamp. Enabling this option will add the
time and date to the bottom-right corner of all video footage.
Language 35. English (Default)
36. French
37. German
Format 38. No
39. Yes
Use this option to format your Micro SD card. Please note that all data will be lost.
Reset Settings 40. No
41. Yes
Use this option to reset all camera options to the factory settings.
Firmware Version The number indicates the rmware version installed on the camera. When new
rmware is successfully installed, this number will change.
F SETTING THE TIME & DATE
1. Open the Camera Setup Menu as described on the opposite page.
2. Highlight the Time or Date setting on page 2 of the Setup Menu and press the
SELECT button.
3. Press the UP and DOWN buttons to adjust the value of the time or date elds, and
the SELECT button to move between hours/minutes or year/month/day.
4. Press the MENU button to save the time/date and return to the Setup Menu.
menu options
130.com.ua
Autogood products «130»

25 26
connecting the camera
You can copy your recorded video footage and photos to a PC or Mac computer by
using the included USB cable.
A CONNECTING THE CAMERA TO A COMPUTER
Connecting to a Windows PC
1. Connect the camera to your PC using the USB cable. The camera LED will turn blue
and the camera will display a black screen.
2. Your operating system may be set up to show a le window automatically.
Otherwise, double-click on the My Computer icon.
3. Your computer should recognize your camera as a Removable Disk. Look for the
DRIFT Removable Disk and double click on it to open it.
4. Double-click on the ‘DCIM’ folder to open it.
5. Inside the ‘DCIM’ folder you will nd a folder called '100DRIFT' which contains all
photos and videos recorded on the micro SD card. If there are a large number of
les, there will be multiple folders - 100DRIFT, 101DRIFT, etc.
6. Copy the desired video and photo les to your PC.
Connecting to a Mac
1. Connect the camera to your Mac by using the USB cable. The camera LED will turn
blue and the camera will display a black screen.
2. Your operating system may be set up to show a le window automatically.
Otherwise, open the Finder.
3. Your computer should recognize your camera as an external device called DRIFT.
Click on it to open it.
4. Click on the ‘DCIM’ folder to open it.
5. Inside, the ‘DCIM’ folder you will nd a folder called ‘100DRIFT’, which contains all
photos and videos recorded on the Micro SD card. If there are a large number of
les, there will be multiple folders – 100DRIFT, 101DRIFT, etc.
6. Copy the desired video and photo les to your Mac.
Note: The battery does not need not be inserted or charged to copy les to a
computer.
Note: You can also copy data from the memory card by using a USB card reader (not
included). Your computer may also have an Micro SD card reader built into it, which
you can use to transfer your files.
B PLAYING THE VIDEO FOOTAGE ON A COMPUTER
1. Some computers may not have the correct codecs required for video playback and
editing.
2. If your experience diculties playing video recorded with your camera, you can
download VLC media player for free from http://www.videolan.org/
3. If you are experiencing diculties editing video or do not wish to use VLC player for
playback, you will need to download and install a codec pack. The FFDshow codec
pack can be downloaded from http://www.free-codecs.com/FFDshow_download.htm
4. Do not forget that to play HD video les on your computer you require a powerful
computer, with a modern video card and plenty of RAM.
C CONNECTING THE CAMERA TO A TV
1. While the camera is turned o, connect it to your TV using a Micro HDMI cable (not
included).
2. Switch the camera on.
3. Once booted up, the image usually displayed on the camera’s LCD screen will
instead be displayed directly on your TV, and the sound will come out of the TV
speakers.
4. All other camera functions and the camera buttons work as normal.
130.com.ua
Autogood products «130»

27 28
replacing the lens
In order to follow the procedure below, you must have a Drift Replacement Lens Kit in
hands (not included in the package).
1. Using the small screwdriver, gently remove the four screws that hold the lens glass
protector.
2. Remove the black frame that holds the lens.
3. Remove the old lens from the frame, including the washer.
4. Taking the new pieces of the kit, insert the lens on the frame, and the washer just
behind the lens.
5. Position the frame on its original place, and gently tight the screws.
130.com.ua
Autogood products «130»

29 30
faqs
What type of memory card does the camera support?
The Drift HD supports Micro SD cards from all leading brands. We strongly recommend you to stick to reliable brands and dealers.
The unit is also compatible with Micro SDHC cards.
What is the biggest Micro SD Card I can use?
The Drift HD supports Micro SD / SDHC cards with a capacity of up to 32GB.
Are the Micro SDXC cards compatible?
No, the Drift HD is not compatible with the SDXC technology.
How does the remote control work?
The remote control uses radio frequency (RF) to communicate directly with the camera unit. The remote is RF based, rather than
infrared (IR), as used in other helmet cameras. As a result, you do not need to point the remote at the camera. As long as the
remote is in range of the camera, it will pick up the remote control signal.
How far will the remote control work?
The wireless remote control has a range of 3 meters (about 10 feet).
What is the remote pairing feature?
The Remote Pairing function links your camera to a specic remote. If unpaired, the camera will work with any Drift HD remote
control in range. This can cause problems if more than one person is using a remote at the same time. Pairing the remote to your
camera will ensure your camera only responds to instructions from your remote control. The Drift HD comes paired with the
remote in the box.
Full instructions on Remote Pairing can be found in the “Using the Remote” section on page 22.
How long will the batteries last?
The Drift HD comes with a 1100mAh rechargeable Lithium-Ion battery. When recording video in 1080p with all battery saving
features switched o, the camera will operate for a total of 3 hours at room temperature, and 2½ hours in cold conditions (such
as -5°C / 23 F), before the battery runs out. Several camera options can be changed in order to extend the battery life – these are
detailed in the “Conserving Battery Life” section on page 19.
In addition, the 1100mAh Drift spare battery is available from Drift dealers. Please visit http://www.driftinnovation.com/ for more
information.
How do I charge the battery?
The battery is charged via a USB port built into the camera. You don’t necessarily have to charge it via a computer however. Many
electronics stores sell USB power adapters that can be used to charge the Drift HD. These have a Mini USB port at one end, while
the other end plugs into a power outlet or wall socket. Please follow the charging instructions on page 11 carefully to ensure the
camera enters charging mode. If the LED does not turn blue, the camera is not charging.
Can I power my camera from a cigarette lighter adapter?
Yes. When connected to a USB cigarette lighter adapter, the unit will draw its power from your bike or car battery. Please note that
while this allows you to power the camera unit, it does not recharge the battery unless you put the camera into charging mode
(page 12). You can buy a USB cigarette lighter adapter from all of our leading dealers or from electrical stores.
The videos and photos give me a slight fisheye eect. Is this right?
Yes. We specically selected a 170° lens to provide users with the quirky wide angle that was prominent in the early days of helmet
cameras, particularly in skateboarding. The eect is less pronounced on objects in the distance and more pronounced on objects
close to the camera lens. If you prefer a tighter angle, you can use the camera’s zoom function, or shoot in 1080p. But we think
you’ll grow to love this classic hallmark of action sports video.
What is the dierence between 1080p and 720p?
The Drift HD can record video in both 1080p and 720p High Denition video formats. 1080p video les have a resolution of
1920x1080 pixels, providing the highest level of video quality but taking up the largest amount of space. 720p les have a resolution
of 1280x720 pixels, providing excellent video with a smaller le size. All three available video formats provide a 16:9 aspect ratio
widescreen image.
What are the dimensions of the video camera?
The dimensions of the camera are 133 (L) x 50 (D) x 33 (W) mm and those of the remote control are 52 (L) x 40 (W) x 13 (D) mm.
Can I connect my camera to a tripod or suction cup?
Yes. The Drift HD comes with a built-in ¼"-20 (8mm) female camera thread. This allows the camera to be mounted directly on any
tripod, suction mount (such as the Panavise 809) or any other camera mount with a ¼" thread. These mounts can be purchased
from all our leading dealers or from camera stores.
How waterproof is the camera?
The Drift HD action camera is weatherproof and water resistant. The camera is fully splash-proof and weatherproof, but it is not
designed to be used in a water environment. Please be aware of this when using the Drift HD. Drift Innovation will not assume any
responsibility for camera malfunction caused by liquid entering the camera as a result of misuse by the user.
What are the benefits of using the camera’s Outdoor Mode?
The Outdoor mode allows the Drift HD to record video and capture photos in a dark environment, such as at dusk. It does this by
increasing the sensitivity of the camera to light. The trade-o is a slight decrease in image quality – the image will contain noise
and possibly be slightly more blurry. Please note that this is normal for digital cameras. The Outdoor mode is also more eective
when capturing photos than when recording video.
How do I connect an external microphone?
An external microphone accessory is available exclusively for the Drift HD - please visit our website www.driftinnovation.com/ for
more details on how to use and where to buy it.
How do I upgrade the camera firmware?
From time to time, Drift Innovation may release new rmware versions to improve the functionality of the Drift HD. These are
not essential, but the updates may improve your recording experience. To be kept informed of new rmware releases, please
register at www.driftinnovation.com/ where you will be able to access and download new rmware along with detailed installation
instructions.
130.com.ua
Autogood products «130»

31 32
system requirements
To smoothly view and edit 1080p HD video, powerful hardware is required
Recommended System Requirements – Windows
• 3.2 GHz Pentium 4 processor or higher
• At least 2GB of RAM
• Graphics Card with at least 256MB of video RAM (512MB for video edition)
• Direct X 9.0c or later
• Microsoft Windows XP (SP2 or later), Windows Vista or Windows 7
Recommended System Requirements - Macintosh
• 2.2 GHz Intel Core Duo or higher
• At least 1GB of RAM
• Graphics Card with at least 256MB of video RAM (512MB for video edition)
• Mac OS X v10.4.11 or later
! High Denition Video requires large
amounts of hard drive space. If your
hard drive is not large enough, you can
purchase an external hard drive to store
your video les. These are relatively
inexpensive, and can also be used to
back up your other computer files as
well.
troubleshooting
The LCD screen does not display anything
• Check that the rechargeable battery is properly installed.
• The battery may need recharging.
• If the LED is switched on, try pressing a button on the control panel. The LCD Auto-O function may be switched on. Please see
page 23 for details.
After the camera is connected to my PC, it cannot find the new drive in the My Computer folder
• Ensure each end of the USB cable is properly connected to your PC and your camera.
• Is there an Micro SD card in the camera’s memory card slot?
• Your USB port may not be working correctly. Try connecting another USB device into the port. If the other device does not work,
the USB port may have a malfunction. In this case, try the other USB ports in your computer. If you still have problems, contact
your system manufacturer or the manufacturer of your USB card.
I can't capture video footage
• Is there a Micro SD card in the camera’s memory card slot?
• There may not be enough space left on the memory card. If the memory card is full, there will be an ‘x’ through the memory card
indicator.
• Ensure the Micro SD card is not locked. The LCD will display a padlock symbol if the card is locked. The card can be unlocked by
sliding a small switch located on the card itself.
I can't play the video footage on my television
• Ensure each end of the component cable is properly and rmly connected to the camera and to the correct ports on your television.
• Check that the camera and television are both turned on.
• Check that you have set the television to display the correct input.
The sound is very low or there is no sound
• Ensure the camera speaker and the camera microphone are turned on in the Setup Menu.
• The camera is specically designed for extreme sports, where noise levels can be very high. As a result, the microphone is less
sensitive than in a regular digital camera. You can increase the microphone sensitivity in the Setup menu.
I can’t view clips on my computer, or I get an error message
• You may have outdated codecs. We recommend using VLC player, which is available for free from www.videolan.org
• If you wish to use WMP or other editing or video playback software you need to install a codec pack. You can download the
FFDshow codec pack for free from http://www.free-codecs.com/FFDshow_download.htm
I switched my camera o during recording, and the video clip is damaged.
• Please ensure that you stop recording before switching o your camera, as this can damage the video clip you are currently
recording.
130.com.ua
Autogood products «130»

33 34
technical specifications
• Sensor type: CMOS
• Water Resistant (weatherproof)
• Video resolution: 1080p, 720p & SD
• Video format: .MOV (H.264 codec)
• Frames per second:
25 / 30 / 50 / 60 / 90 FPS in SD
25 / 30 / 50 / 60 FPS in 720p
25 / 30 FPS in 1080p
• Video format: 16:9
• Lens Rotation: 300°
• Recording Angles: 127° in 1080p, 170° in 720p & SD
• Exposure: Auto / Manual (advanced users)
• Zoom: Digital x4 (in 1080p, 720p & SD resolutions)
• Remote range: 3 meters (10 feet)
• Built-in Microphone
• Inputs: 2.5mm External Microphone
• Audio/Video Output: Micro HDMI (cable not included)
• Battery: 1100mAh rechargeable lithium-ion
• Power-Save option saves batteries by powering down the screen
• Memory capacity: Supports Micro SD memory cards up to 32GB
• Photo resolution: 9 Megapixel
• LCD screen: 1.5” colour TFT
• Lens focal range: 0.5m to innity
• Dimensions:
Camera - 105 (L) x 50 (D) x 37 (W) mm
Remote Control - 52 (L) x 40 (W) x 13 (D) mm
• Power: Camera - DC 3.7V / Remote control: DC 3V, 1x CR2032 battery (included)
• RF: Receiver (Camera): 433.92MHz ISM band / Transmitter (Remote): 433.92MHz
ISM band
• Weight: Camera - 120g / Remote control - 19g
• Operating Systems: Compatible with Windows XP, Vista & Windows 7; Mac OS 10.2
onwards.
further help
We make every eort to ensure the accuracy and appropriateness of the information
provided on our products. We encourage you to contact our Technical Support Team
on [email protected] with any problems and/or suggestions.
Please note that the Technical Support Team cannot issue or authorise any Returns /
RMA's or replacements.
For a Return / RMA or replacement please contact the place of purchase.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) ....... this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
WARNING
Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
NOTE
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment o and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the
receiver is connected.
• Consult the dealer or an experienced radio / TV technician for help.
130.com.ua
Autogood products «130»

35 36
INFORMATION FOR USERS
In accordance with European Directives 2002/95/CE, 2002/96/CE and 2003/108/
CE on the restriction of the use of dangerous substances in electric and electronic
equipment as well as their waste disposal.
This symbol shown on the equipment indicates that, at the end of its useful life, the
product must be collected separately from other waste.
Therefore, any products that have reached the end of their useful life must be given
to waste disposal centres specialising in separate collection of waste electrical and
electronic equipment, or given back to the retailer at the time of purchasing new
similar equipment, on a one for one basis.
The adequate separate collection for the subsequent start-up of the equipment
sent to be recycled, treated and disposal of in an environmentally compatible way
contributes to preventing possible negative eects on the environment and health and
optimises the recycling and reuse of components making up the apparatus.
Abusive disposal of the product by the user involves application of the administration
sanctions according to the laws in force.
CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
warranty
Thank you for purchasing the Drift HD. We are condent you will have great fun with
your brand new Drift camera!
Warranty
To obtain our warranty service, register your product at www.driftinnovation.com as
soon as you purchase it.
Customer Support
• Check www.driftinnovation.com for rmware updates, product updates and user
videos.
• We are here to help. If you have any suggestions, comments or problems, please
contact our customer support team on [email protected].
130.com.ua
Autogood products «130»