DSPPA PAVA6500 User manual

Operation Manual for PAVA6500 System
Guangzhou DSPPA Audio Co., Ltd
PAVA6500
PAVA6500E
PAVA6006
PAVA6000

1 of 3
About this Manual ................................................................................................................................... 3
Overview of the System......................................................................................................................... 4
Characteristics of the System................................................................................................................ 4
Configuration of the System.................................................................................................................. 5
1. PAVA6500/PAVA6500E (Control Host/Extended Host)..................................................................... 5
1.1. Front Panel.................................................................................................................................. 6
1.2. Rear Panel................................................................................................................................. 10
1.3. Technical Specification............................................................................................................. 15
Electrical Indicators................................................................................................................ 15
Mechanical Indicators............................................................................................................ 16
Environment Requirements.................................................................................................. 16
2. Business MIC——PAVA6006 .............................................................................................................. 17
1.4. Front/Rear Panels...................................................................................................................... 17
1.5. Technical Specification............................................................................................................. 20
Electrical Indicators................................................................................................................ 20
Mechanical Indicators............................................................................................................ 20
Environment Requirements.................................................................................................. 20
3. Wiring Diagram of the System ............................................................................................................ 21
4. Routine Operation................................................................................................................................. 21
4.1. Host Lines 01-06 for Manual Playing.......................................................................................... 22
4.2. Manual Playing of EVAC Voice.................................................................................................... 22
4.3. Automatic Triggering of EVAC Voice.......................................................................................... 22
4.4. PAVA6000 Operation..................................................................................................................... 23
4.5. Paging Operation Using Emergency Microphone.................................................................... 24
4.6. Operations in PAVA6006 are as follows..................................................................................... 24
Software Introduction (PAVA6000) ..................................................................................................... 24
Description of Icons in the Software................................................................................................... 24
Note: HOST 01 represents the system host, namely, PAVA6500, and the extended host 1 is: HOST
02 Initialize..................................................................................................................................................... 25
2. Initialization............................................................................................................................................. 26
2.1. Computer configuration............................................................................................................ 26
2.2. Installation................................................................................................................................ 26
2.3. Uninstall.................................................................................................................................... 28
2.4. Operation.................................................................................................................................. 28
2.4.1. Software Login................................................................................................................ 28
2.4.2. Introduction of Control Interface................................................................................... 30
2.4.2.1. Introduction of Menu Bar and Tools.................................................................. 30
2.4.3. Introduction of “Current Operating Interface Selection”............................................ 31
2.4.3.1. Partition Control ................................................................................................ 31
2.4.3.2. System Equipment State (STATE)..................................................................... 33
2.4.3.3. SYSTEM CONFIGURATION .......................................................................... 34
2.4.3.3.1. Check the Detailed Configuration Parameters of the System
Equipment 34
2.4.3.3.2. Fire Rules.................................................................................................. 37

2 of 3
2.4.3.3.3. Grouping Configuration of the System................................................. 38
2.4.3.3.4. Configuration of Audio Priority of the System...................................... 39
2.4.3.4. Log Query of Equipment Modules.................................................................... 40
2.4.3.5. “OTHER” (Other settings)................................................................................. 41
Precautions............................................................................................................................................ 43

3 of 3
About this Manual
Objectives of this Manual
Provide the information required for installation, configuration and operation of PAVA6500
Voice Alarm System.
Target Users
Users and Installers of PAVA6500 Voice Alarm System;
Terminology
“System Host” —— PAVA6500；
“Extended Host” —— PAVA6500E；
“Business MIC” —— PAVA6006；
“Control Software” —— PAVA6000；
Note: The software functions of this system will continue to upgrade, but it will be backward
compatible, so please pay an attention to the real-time information of the website of the
Company.

4 of 3
Overview of the System
PAVA6500 voice alarm system is the public address and voice alarm system. It has integrated
with the EN60849, BS5839/8, EN54-16 and other evacuation standards. It is usually used in the
small-scale systems that must meet the evacuation standards or the systems whose application can
be met only when one call channel is required.
Characteristics of the System
Comply with the requirements of national standard GB16806-2006 and European
Voice Alarm Control and Indicating Equipment Standard EN54-16;
Automatic system fault diagnosis, data backup, redundant line and record fault
status (<=5000 records) are safe, stable and reliable;
Compatible with the wiring standard of 3-wire and 4-wire systems;
Built-in emergency voice message and tone information. The user can freely
replace them according to the site environment, language and their fancies.
Programmed to partitions, support manual, automatic, partition and grouping
operations;
Support the visual human-machine interface operation and control, support
simultaneous operation and control of multi-windows human-machine interfaces.
Offline operations are available after the configuration.

5 of 3
Configuration of the System
Equipment Introduction
1. PAVA6500/PAVA6500E (Control Host/Extended Host)
PAVA6500 is the core of voice alarm control of EVAC System, built-in with 240W/350W/500W
digital amplifier, which not only is available for early warning and alarming(Both alarming way and
voice can be achieved by way of programming), but also can realize the evacuation guidance on the
site via the handheld microphone, and control the emergency calls and business broadcasting of up
to 120 partitions as well as the play of background music.
Handheld microphone is available for site evacuation in case of any emergency;
Built-in EVAC voice message and Chimes Management for a real-time monitoring.
Notes:
1. Audio message format extension is: *.wav;
2. The message number under the directory of “evac_message/”and “alert_message/” and “prompt/” in
the SD card shall be controlled within 255;

6 of 3
Built-in 240W/350W/500W digital function amplifier, and meanwhile available to connect a backup
amplifier of the same power to realize the automatic replacement;
Note: please keep pace with the actual configuration. For example, if a backup amplifier is configured by
the user and no backup amplifier of the same power or above is in fact connected, in such a case, the host
is unable to detect the existence of the spare power amplifier.
6 partitions; each partition can output 500W;
Note: total power of 6 partitions cannot exceed 500W;
Available for external connection of 6-line inputs to play the background music;
Support event linkage and partition output;
up to 3000 status records of equipment modules, including power module, handheld microphone module,
voice message module, power amplifier module, speaker circuit module, etc. (please consult the related
descriptions in PAVA6000);
Able to simultaneously connect up to 32 PAVA6006 systems with a distance of at least 600m;
Support line redundant wiring between business microphone, host and extended host;
Note: total length of hand-in-hand redundant line shall be less than or equal to 600m.
1.1.Front Panel
19 20 21
79
22
810 11
23 24
12 14
13 15 16 17 18
3
4
5
6
1
2

7 of 3
22
11
23 24
12 14
13 15 16 17 18
3
1
2
DIGITAL VOICE EVACUATION EXTEND AMPLIFIER
1 —— Main power indicator of the host:
Green – indicating that the current host AC power supply is normal;
Yellow – indicating that the current hostAC power supply is in trouble;
2 —— DC24V Backup Power Indicator of the Host
Green – Indicating that the current host backup power supply is normal;
Die-out (OFF) – Indicating that the current host backup power supply is not configured;
Yellow – indicating that the current host backup power supply is in trouble.
Note: , in the left chart (host is the second bit in PAVA6500 and host is the sixth bit in
PAVA6500E), pull-up indicates that the system is configured and pull-down indicates that the system is not
configured.
3 ——Connection Status Indicator of Host/Extended Host
Yellow – indicating that the current extended host does not establish the logical or physical connection with the
host;
Die-out (OFF) – indicating that the current host does not establish the logical or physical connection with
PAVA6000;
Green – Indicating that the current equipment is connected normally.
4 —— Equipment Status Indicator
Die-out (OFF) – Various modules of the system work normally (it will also die out if the total detection switch is
prohibited, but this does not indicate that all modules are normal);
Yellow – System is in trouble (if the system is not failed but this indicator light still flashes, please press the Key
“ACK/RESET”).
5 ——Status Indicator
Yellow – Indicating there is a fault when the handheld microphone is lost or failed;
Green – Indicating that the microphone is operating;

8 of 3
Die-out – Indicating that the handheld microphone is normal but it does not work.
6 —— System Equipment LED Indicator Test (mainly test the LED of host/extended host and business microphone
panel)
Note: if there is an extended host or business microphone in the system configuration, it will enter LED test
model after pressing this key.
7 —— System Work Mode Indicator
Red Flash – Indicating the current system is in an emergency mode;
Die-out – Indicating the current system is in a normal mode;
Two Ways to Enter the Emergency Mode:
Manual Mode – under the normal mode, the red indicator light flashes after pressing this key, which indicates
that the system manually enters the emergency mode;
Automatic Mode – under the normal mode, after detecting the effective triggering signals at the rear row
“TriggerInputs” of the host or extended host, this indicator light will also flash, which indicates that the system works
in the emergency mode.
Two ways to exit the Emergency Mode:
Manual Mode – Under the emergency mode, the system exits from the emergency mode by pressing this key,
and meanwhile it stops the playing of EVAC voice message and the partition output;
Automatic Mode – under the emergency mode, it can exit from the emergency mode by way of direct short
circuit at 2 input ports of rear row “System Link Control” port 3, and meanwhile, it stops the playing of EVAC voice
message and the partition output.
Note: no matter whether it is a manual entry (exit) or automatic entry (exit), its execution time and way can be
checked in the LOG of PAVA6000.
8 —— Multi-purpose Reset Key (ACK/RESET):
Answering System Status -
a. if various system modules work normally or when the diagnosis of system modules is abnormal but “FAULT”
indicator light does not flash, no treatment is made to the equipment after pressing this key;
b. If the diagnosis of system modules is abnormal and “FAULT” indicator light intermittently flashes, after
pressing this key, “FAULT” indicator light is ON and does not flash any longer, which indicates its fault status,
and the buzzer stops until the FAULT LED light re-flashes after abnormity is detected in new module and the
buzzer is started to prompt the user;
c. When there is any output from the current partitions, press this key to close the current audio output and
quickly end the broadcasting.
9 /10—— EVAC Voice Message Status Indicator
Green – “EVAC MSG/ALERT MSG” voice message is broadcasting;
Yellow - “EVAC MSG/ALERT MSG” voice message is lost or SD Card is lost;
Die-out (OFF) - “EVAC MSG/ALERT MSG” voice message is normal.
Note:
1. ”EVAC Voice Message” means the general designation of EVAC voice and ALERT Voice;
2. If any user wants to manually play the EVAC voice message, he/she shall enter the emergency mode and then
press the voice message key;
3. In the system default, the priority of “EVAC” Voice is higher than that of “ALERT” Voice. Of course, it can be altered
through the priority configuration of PAVA6000. If it is not a specific application need, please do not change it.

9 of 3
○,11 —— Line Output Selector Switch
Mainly used to select the output audio of current partition;
Note: the current selection of the user can be checked via the interface of PAVA6000. When it is
required to change different audio output, it can only be selected from the panel.
○,12 —— ON/OFF Selection of Partitions (Partitions)
If the current partitions are closed, they shall be all opened (ON); if the current partitions are all opened, they
shall all be closed (OFF).
○,13 —— Speaker Partition Status Indicator
Yellow – indicating there is a change of impedance of Speaker A or Speaker B or the current partitions A or B,
which may cause the open circuit or short circuit;
Die-out (OFF) – indicating that the change of speaker circuit impedance of current partitions is within the
impedance range during the modeling of speaker partitions;
Note: it is required to conduct an impedance method calibration to obtain the impedance value of current speaker
circuit before the host or extended host is wired into the system. The method is as follows:
Pull down the seventh bit of rear row ID switch of the host until you hear the alternate beeps of the buzzer or see the
flash of FAULT Indicator Light on the panel before pulling up the seventh ID switch. When the impedance variation of
speaker circuit exceeds the ± 10-30% of impedance value acquired by the current host or extended host, the current
variation will then be recorded and it will be informed to the user in the form of sound and light. The detection
sensitivity of partitions /partitions is equal to or greater than 20W.
14 —— Partition PTT or Remote Business Microphone Paging Indication
Note: for a paging service, the user can manually close the partitions that are not call or increase the new
partitions.
15 ——Indication that the Partition is Broadcasting “EVAC” Voice Message
Note: the user can manually close the partitions that are not call or increase the new partitions.
16 —— Indication that the Partition is Broadcasting the Background Music
Tip: it is required to select the audio before selecting the output partitions while manually playing the voice
message. For example, if you want to output the audio of Line 3 to the Partition 3, you can select the partition before
selecting the audio, or you can select the audio before selecting the partition. Of course, the final outcomes are the
same. In general, it is habitual to select the partition before selecting the audio. In such a way, various partitions will
output the audio simultaneously, and in addition, it can be operated in the partition control interface of PAVA6000.
17 —— Partition Selection Key
Notes:
1. If one of the current partition output indicator lights “PAGING”, “EVAC/ALERTA” or “BGM” is ON, it will close the
output of current partition by pressing this key;
2. If none of the current partition output indicator lights “PAGING”, “EVAC/ALERTA” or “BGM” is ON, one of them will
be ON by pressing this key (The corresponding LED light is ON according to the current output audio).