Ropam elektronik NeoGSM-IP User manual

NeoGSM-IP –alarm panel with build-in automation
and WIFI.
Ropam Elektronik
Tel. [phone]
Faks [phone]
Polanka 301
32-400 Myślenice, Polska
www.ropam.com.pl
[e-mail]
Document version : 1.0
2018-04-01
User manual.

© 2018 Ropam Elektronik
WARNINGS
For safety reasons, the device should only be installed by qualified specialists.
Before starting the assembly, read the instructions above, the connection operations
should be carried out without the power supply connected.
Do not turn on the power of the device without an external antenna connected (starting
the device without the antenna connected may damage the transmitting circuits of the
phone and void the warranty!).
Do not interfere with the construction or carry out independent repairs.
Protect the electronics against electrostatic discharge.
In order to meet the requirements of LVD and EMC, the following rules must be observed:
power supply, installation, shielding - according to the application. The device is a source
of electromagnetic waves, so in specific configurations it can interfere with other radio
devices).
The Ropam Elektronik company is not responsible for the malfunctioning of the GSM
network and the consequences of possible technical problems.
WEEE LABELING
Waste electrical and electronic equipment must not be disposed of with normal
household waste. According to the WEEE directive (Directive 2002/96 / EC) applicable
in the EU for the used electrical and electronic equipment, separate disposal methods
should be used. In Poland, in accordance with the provisions on waste electrical and
electronic equipment, it is forbidden to put waste equipment together with other waste
marked with the symbol of a crossed out basket. The user who intends to get rid of this
product is obliged to hand over the above-mentioned to the point of collecting used
equipment. Collection points are carried out, among others by wholesalers and retailers
of this equipment and communal organizational units conducting business in the field of
waste collection. Proper implementation of these duties is important especially when
there are hazardous components in the used equipment that have a negative impact on
the environment and human health.
The control panel power supply cooperates with a 12V DC lead-acid dry battery (SLA,
VRL). After the period of use, it should not be disposed of, but disposed of in a manner
consistent with applicable regulations.
(Directives of the European Union 91/157 / EEC and 93/86 / EEC).

© 2018 Ropam Elektronik
Table of contents
1. General description. .................................................................................................................... 1
Properties........................................................................................................................................ 1
Appliance. ....................................................................................................................................... 1
Warnings......................................................................................................................................... 2
Requirements for SMS, DTMF control............................................................................................ 3
2. System operation. ....................................................................................................................... 4
TPR-xx touch panel. ....................................................................................................................... 4
Main window................................................................................................................................ 5
Description and functions of icons. ............................................................................................. 5
Status bar.................................................................................................................................. 11
Acoustic signaling...................................................................................................................... 11
System operation. ..................................................................................................................... 11
Arming full armed mode......................................................................................................... 12
Arming night mode................................................................................................................. 13
Disarming............................................................................................................................... 13
Canceling alarm..................................................................................................................... 14
System status preview........................................................................................................... 14
Event history.......................................................................................................................... 15
Editing codes. ........................................................................................................................ 16
Preview of system failures..................................................................................................... 16
Settings.................................................................................................................................. 16
Blocking zones....................................................................................................................... 16
Outputs controling.................................................................................................................. 17
Relay controling..................................................................................................................... 17
SD, SDHC card...................................................................................................................... 18
Room thermostat................................................................................................................... 18
Touch panel TK-3W / TK-3B......................................................................................................... 19
Description. ............................................................................................................................... 19
Numeric keyboard operations. .................................................................................................. 19
System operations..................................................................................................................... 20
Service operations..................................................................................................................... 21
RopamNeo application.................................................................................................................. 22
Remote controllers........................................................................................................................ 23

© 2018 Ropam Elektronik
Keyfob Aero............................................................................................................................... 23
TR-4H........................................................................................................................................ 23
SMS control................................................................................................................................... 25
SMS control: system arming. .................................................................................................... 25
SMS control: blocking zones..................................................................................................... 25
SMS control: outputs................................................................................................................. 25
Control of the video intercom.................................................................................................... 26
ThermostatGSM: monitoring and changing temperature thresholds........................................ 27
AI input: change of voltage thresholds...................................................................................... 27
Control of the Aero wireless system.......................................................................................... 28
System status............................................................................................................................ 28
Transmission test................................................................................................................... 28
System status: SMS STATUS............................................................................................... 29
System status: Zones status SMS......................................................................................... 31
USSD codes; top-up prepaid account................................................................................... 31
USSD check codes for prepaid account status..................................................................... 32
Remote configuration of selected functions: SMS................................................................. 32
Other sms commands............................................................................................................... 33
DTMF control. ............................................................................................................................... 36
DTMF control: arming................................................................................................................ 36
DTMF control: outputs............................................................................................................... 36
DTMF control: end of queue for VOICE.................................................................................... 37
DTMF control: door intercom bolt.............................................................................................. 37
Version history.................................................................................................................................. 38
Information........................................................................................................................................ 38

Str. 01
General description.
© 2018 Ropam Elektronik
1. General description.
Thank you for choosing Ropam Elektronik products and solutions. We hope that our devices will meet
your requirements and will serve you reliably for many years. The Ropam Elektronik company is
constantly modernizing its products and solutions. Thanks to the update function, products can be
enriched with new functions and keep up with the requirements set for modern property protection
systems and home automation. We invite you to visit our website www.ropam.com.pl in order to
obtain information about current versions. If you have additional questions, please contact us by
phone or by email.
Properties.
The NeoGSM-IP alarm control panel with peripheral devices is a solution that integrates electronic
burglary signaling system and building automation. Built-in GSM communicator allows remote control
and control of the system. Thanks to the modular design, the system can be expanded and adapted to
the changing needs of the user.
Control panel has unique functions compared to competing products and is the most functional system
on the market in its class, including:
- 2 independent zones with two types of waking: full or night,,
- 8-32 programmable zones, expansion by zone expanders, touch panels, Aero wireless system,
- 8-24 programmable outputs, expansion by output expanders,
- support for up to 4 touch panels (TPR-4x / 4xS series) or touch keyboards (TK-3x),
- built-in GSM modem and WIFI module (ETH EXP-LAN option),
- notifications of type: SMS / CALL / E-MAIL / PUSH,
- mobile application support: RopamNeo Alarm Control, for online supervision via the Internet,
- IP communication: WIFI / LAN basic channel, GPRS backup channel (automatic switching),
- Internet control for the IP channel: support for permanent IP / domain or RopamBridge server (any
Internet),
- Internet control for the GPRS channel: support for the encrypted RopamBridge server ('Internet
router by ID'),
- 4 timers with a calendar, for control and automation,
- operation of temperature and humidity sensors (wired, wireless), 'Room thermostat' function,
- cooperation with the -ECO power supplies, energy and cost savings,
- advanced logic functions and software time relays, LogicProcessor,
- local programming via micro USB or WIFI / ETH,
- software remote via the RopamBridge server (GPRS or IP),
- a version in the housing for the DIN rail is also available.
Appliance.
The alarm system built on the basis of NeoGSM-IP series alarm panels, TPR-xx touch panel and other
additional devices is an ideal solution for residential buildings and small commercial facilities. Modern
design, proven touch panel technology with a spectacular color LCD display is ideal for incorporation
in most interiors and rooms. Intuitive and clear interface, I make controlling the alarm system has never

Str. 02
General description.
© 2018 Ropam Elektronik
been as easy as with TPR-xx. The touch panel in combination with the control panel allows you to build
a fully functional alarm system.
NeoGSM-IP control panel also allows you to create simple home automation applications with remote
control via SMS / CLIP and Wifi / Ethernet.
Flexible functions also allow for use in systems that use binary signal control, temperature, visual
verification is required and information transfer is based on SMS, VOICE, e-mail.
• building automation systems integrated with the NeoGSM-IP system,
• smart home, home automation,
• electronic burglary and assault signaling systems,
• signaling systems: fire, gas leaks, flooding, power supply status, UPSs,
• remote control of electrical devices,
• intelligent lighting,
Warnings.
Ropam Elektronik devices are part of a full alarm system, whose effectiveness depends on the quality
and technical condition of all devices (detectors, signaling devices), cabling, etc. included in the system.
The user is obliged to periodically test the operation of the alarm system. It should be checked whether
the control panel reacts to the violation of individual detectors (PIR, reed switches, etc.) or signaling
devices (external and internal) and notifications. The detailed method of system control is determined
by the installer that the system has designed. Periodic system maintenance is recommended (with
device status check, back-up power supply, system operation, messaging, etc.).

Str. 03
General description.
© 2018 Ropam Elektronik
Ropam Elektronik is not responsible for the correct operation of operators and GSM network
infrastructure used for notification of alarm states and remote control. It is recommended to use
a GSM operator that guarantees coverage of min. two BTSs of a given system location with GSM
communication.
We do not recommend using operators using national roaming!
In addition, it should be noted that services guaranteed by GSM operators are voice transmission
services (VOICE) and not SMSs, that is why important information should be transmitted through voice
calls and possibly accurate identification of the event takes place in an SMS (eg VOICE + SMS, CLIP +
SMS).
In addition, we recommend using such services and subscriptions available on the market that
guarantee correct operation (minimizing the human factor, eg blocked outgoing calls due to lack of funds
on the account), allow full configuration of GSM bus occupancy (eg, exclusion of advertising services
not available in services pre-paid). In addition, it should be noted that services guaranteed by GSM
operators are voice transmission services (VOICE) and not SMSs, that is why important information
should be transmitted through voice calls and possibly accurate identification of the event takes place
in an SMS (eg VOICE + SMS, CLIP + SMS)..
For e-mail transmission services, it is recommended to create an independent e-mail account (eg
[e-mail]) from a verified provider of e-mail accounts. Sharing data to an SMTP server from
private accounts may result in access to these accounts by unauthorized persons.
Requirements for SMS, DTMF control.
To operate via SMS mobile phone, the smartphone must encode SMS: GSM or UNICODE alphabet
other formats are not supported!
To control the DTMF phone, the smartphone must be able to generate DTMF tones during a phone
call.
A single DTMF code (pressing the sign) should last for a minimum of 0.5s.

Str. 04
System operation.
© 2018 Ropam Elektronik
2. System operation.
TPR-xx touch panel.
TPR-4W/WS
TPR-4B/BS
The TPR-xx touch panel is a modern element of control and alarm system control.
TPR-xx is based on a color TFT LCD display with a touch panel.
TPR-xx allows for intuitive control and control of the alarm system, thanks to the interactive interface
using pictograms and text prompts, navigating and using functions is simple and does not require the
user to remember the function code, eg strong vigilance, blocking the sensors..... Control panel has

Str. 05
System operation.
© 2018 Ropam Elektronik
pictograms on which it continuously presents all important information, including standby, power
status, GSM range, GPRS, temperature.
When designing the panel and interface, we were guided by the following slogan:
"Technology for huma, not human for technology".
Main window.
In normal mode, the main window is displayed on the touch panel. TPR-4 panel has the ability to
define two user screens with any configuration of icons on the screen. In the case of inactivity (about
160 seconds), the screen goes into the screensaver mode:
- calendar with date and time, temperature value from system sensors,
- digital photo frame.
In the screensaver mode, information about the armed mode is hidden and the power supply, alarm
and malfunction status is displayed (by means of LED diodes). Exiting the screen saver mode can
be protected by a code. If a code is required, the numeric keypad will be displayed, enter the
code and confirm #. If the sequence is correct, the panel will display the main window. In this
mode, counting of incorrect attempts to enter codes may also work (if global counting is set, for
attempts to bypass the system by guessing codes).
Description and functions of icons.
Icons pictograms are assigned to individual system functions, the meaning and operation of which are
described below. TPR-4 touch panel allows you to place any icons anywhere on the two panel screens
and some of them assign multiple actions.
Icon
Description
Full system utilities.
Possible (set in NeoGSMIPManager):
- selection of zones
- required code
- displaying the zone selection screen

Str. 06
System operation.
© 2018 Ropam Elektronik
Icon
Description
Disarming the system.
Possible (set in NeoGSMIPManager):
- selection of zones
- displaying the zone selection screen
Night time system.
Possible (set in NeoGSMIPManager):
- selection of zones
- required code
- displaying the zone selection screen
Controlling the outputs:
Possible (set in NeoGSMIPManager):
Display of outputs to be available for control
Preview of the zone status (violation, tamper, OK).
Building plan preview (requires a MicroSD card with files: plan1.bmp to
plan4.bmp).
Possibility to edit the layout of detectors on the set from the service menu
level in the TPR-4 panel.
Giving, changing, deleting user codes and names (up to 32).
Menu of user and service settings.
Blocking an input or group of inputs.
Set in the NeoGSMIPManager:
- entry number
- group blocking of zones

Str. 07
System operation.
© 2018 Ropam Elektronik
Icon
Description
- code request to confirm the block
After disarming the entry system they are unlocked.
View history of events in the system.
Overview of system failures.
If a system failure occurs, next to the icon on the right side a yellow dot will be
displayed indicating the presence of a new failure in the system, you can
check by clicking the triangle icon with an exclamation mark.
Preview values for the analog input.
Possible (set in NeoGSMIPManager):
- scaling of voltage values to physical values, e.g. ° C,% Rh, lux, etc.
Temperature chart from TSR-1 sensors connected to the system.
Preview of the entrance.
Possible (set in NeoGSMIPManager):
- selecting the zone number
- blocking the zone after pressing the icon (after disarming the entry system
they are unblocked)
- indication of the status from the PLC I / O module input
Room thermostat.
Possible (set in NeoGSMIPManager):
- thermostat selection (No. 1 or No. 2).
Controlling relay in touch panel.

Str. 08
System operation.
© 2018 Ropam Elektronik
Icon
Description
Controlling of control panel output. (1-24).
Possible (set in NeoGSMIPManager):
- output number
- status indication according to zone
- requiring a code to enable output
Controlling control panel output. (1-24).
1 = white bulb icon
0 = dark bulb icon
Controlling control panel output (1-24). e.g. roller blinds.
Controlling the control panel output (1-24). e.g. roller blinds down.
Controlling control panel output (1-24). e.g. gate.
Controlling control panel output (1-24). e.g. a garage door.
Enabling output group.
Possible (set in NeoGSMIPManager):
- number of output / outputs
- requiring a code to enable
Turning off output group.
Possible (set in NeoGSMIPManager):
- number of output / outputs
- requiring a code to enable

Str. 09
System operation.
© 2018 Ropam Elektronik
Icon
Description
Humidity indicator - Aero radio sensors.
Possible (set in NeoGSMIPManager):
- list of displayed sensors (up to 4)
- sensor number on the widget
Humidity and temperature indicator - radio sensors of the Aero system.
Possible (set in NeoGSMIPManager):
- list of displayed sensors (up to 4)
- display only temp., only% Rh
or temp and% Rh
Basic information about the system:
Firmware of control panel,
Panel firmware,
Power supply to control panel and modem,
Status of AP-IP module
Panic
Fire
Single output control. Fan
Single output control. Heater
Single output control. Power supply

Str. 10
System operation.
© 2018 Ropam Elektronik
Icon
Description
Single output control. Sprinklers
Wicket
Single output control. Garden lights
Single output control Plugin
Single output control Left
Single output control Right
Single output control. Up

Str. 11
System operation.
© 2018 Ropam Elektronik
Icon
Description
Single output control. Down
Status bar.
In the upper part of the LCD display there is a status bar, on which the system status is presented by
pictograms. The bar is displayed in every window and menu.
Acoustic signaling.
Touch panel can additionally generate acoustic signals. Sounds marked with "service" can
be optionally turned off or attached from the installer menu and "user" from the user menu.
one short at 0.2 seconds
signaling of pressed 'button' on the touch panel (service)
two short at 0.85 seconds
wrong code or command
two sets of four signals in one
second
signaling of arming: full or night
one set of four signals within
0.5 seconds
signaling the disarming of full or night standby
one long
every 1 second
signaling of countdown of entry / exit time (service)
one continuous signal
modulated for 0.8 seconds
chime signal from the entrance (user, service)
continuous loud signal
alarm signaling in the system (service)
System operation.
Basic operation of the system consists in pressing the button from the main window and following the
instructions. Numeric keypad (fixed or random arrangement of numbers and characters - service) is
displayed for functions that require confirmation with a code. For functions that require the use of
letters and other characters, a full virtual keyboard (QWERTY) is reported. For selected functions an
optional application without a code is available (designation: service).
Window type / Keyboard
Confirmation of the function
Exit from function
Numerical
#
*
Full
ENTER
ESC
Graphic

Str. 12
System operation.
© 2018 Ropam Elektronik
Full
keyboard:
buttons
Function
0-9
number buttons
A-Z
alphabetic buttons
SHIFT
changing size of alphabetic characters
123
calling / hiding the numeric keypad
PL
calling alphanumeric buttons with diacritical signs (Polish)
Bspace
Backspace button, erases one character back
Space
Space button, space, space
Enter
change approval button
Esc
exit button from the keyboard without saving data
Arming full armed mode.
To activate the full armed mode, press
- the numeric keypad will be displayed, enter the code and confirm #. If the sequence is correct,
the control panel will display partitions selection window.
Select the selected partition (by pressing partition name) and confirm or select the all button.
- if the "quick exit" (service) option is activated, the control panel will start the countdown of the exit delay
for the set partitions
Warnings, depending on the system settings (service):
- if the zones of the control panel are violated, a message will be displayed asking for blocking
the zones:
"Block violated inputs? - YES / NO",

Str. 13
System operation.
© 2018 Ropam Elektronik
if the inputs are blocked from the menu, the following message will appear: "Violated inputs blocked".
Zones violated and not blocked will be normally supervised when they return to normal (not affected). If
the control panel was in the night-time armed mode, this state will change to stand-by mode (without
disarming the night watch).
- if the system is signaled by a failure:
"Malfunction found, arm anyway? -YES/NO".
After confirming the arming, the exit delay countdown begins. Supervision over the detectors will take
place after this time has elapsed.
If the control panel has the Aero system installed, supervision (status transfer) above these detectors
will take place in accordance with the presence control interval, intervals: 30/60 / 90s (service).
Arming night mode.
In order to arm the night (supervision), ie the zone marked as "night" in the zone configuration (service),
press .
- if a code is required, the numeric keypad will be displayed, enter the code and confirm #. If the
sequence is correct, the control panel will display the zone selection window.
Select the selected zones (by pressing the zone name) and confirm or select the all button.
- if the "quick exit" (service) option is activated, the control panel will start the exit delay countdown.
Warnings, depending on the system settings (service):
- if the zones of the control panel are violated, a message will be displayed asking for blocking
the zones:
" Block violated inputs? - YES / NO ", if the inputs are blocked from the menu, the following message
will appear: "Violated inputs blocked". Zones violated and not blocked will be normally supervised when
they return to normal (not affected). If the control panel was in the night-time armed mode, this state will
change to stand-by mode (without disarming the night watch).
- if the system is signaled by a failure:
"Malfunction found, arm anyway? -YES/NO".
After confirming the arming, the exit delay countdown begins. Supervision over the detectors will take
place after this time has elapsed.If the control panel has the Aero system installed, supervision (status
transfer) above these detectors will take place in accordance with the presence control interval, intervals:
30/60 / 90s (service).
Night-time armed mode is a partial arming of zones with the inputs (detectors) assigned to the NIGHT
partitions.
Disarming.
To disable the full or night standby mode, press , then the numeric keypad will be displayed. Enter
the code and confirm #. If the sequence is correct, the control panel will display a zone selection
window with their guard status.
Select partitions (by pressing partition name) and confirm or select the all button.

Str. 14
System operation.
© 2018 Ropam Elektronik
If the "delayed" input is violated during the armed mode, the numeric keypad will be displayed
automatically.
Canceling alarm.
If an alarm occurs in the system, it is signaled in the panel by the red "ALARM" LED, acoustic signaling
and the "ALARM" information window. LCD display in the ALARM window shows the sources of alarms
with the name of the zone (detector) and date. After confirming "ALARM" window, numeric keyboard will
be displayed. Enter the code and confirm #. If the sequence is correct, the control panel will delete the
alarm and disarm the partition (if the control panel was in armed mode).
Delete alarm can also delete any notification action; SMS, SMS + VOICE, VOICE (service).
If the system is configured with alarms from temperature sensors T1-T4 and / or from the
analog input AI, they can be presented as alarms in accordance with the entered descriptions
(service), eg high temp. boiler CO. Above alarms of temperature or analogue alarms do not
generate the alarm status of the intrusion system.
System status preview.
In order to view the current state of zones, press . Zones are viewed after pressing button (if
the system has EXP-I8, EXP-I8-RN zones modules installed, the Aero system and touch keyboards).
Pressing again will return to the preview of previous inputs. During the preview, the display will
show the graphic status of the zones: status + name of the zone. Status is presented through a colored
semaphore, where the color means:

Str. 15
System operation.
© 2018 Ropam Elektronik
Touch panel will remain in zone preview mode until the function exits via X. The screen saver will also
be inactive.
If the Aero system is in the system, the following symbol may appear next to the zone status (detector):
low voltage of the battery , which informs about the need for replacement of the battery in a given
device by the service. If other Aero devices are installed in the system and operate under similar
broadcasting conditions, they probably also need to be controlled and possibly changed batteries.
Pressing button enables a preview:
- synoptic board: if there is an SD card installed in the panel with the file 'plan.bmp' and detectors
(service) are arranged, then there is a view of the building plan with the detectors deployed (service).
- temperature histogram: after pressing the button and if the TSR-1 sensors are installed in the
system, the panel switches to the display mode of current measurements from temperature sensors:
T1- red, T2 - blue, T3- yellow, T4 - green.
Graph is scaled automatically and refreshed every1 minute, ie one pixel is one measurement. In addition
to the histogram, the function of registering the temperature history on the SD card (service) is available
on the display, for each day a file with data in the format rr_mm_dd.txt is created. for further data
processing,
- analog value measured by AI input, 0-10V, unit [mV]. Measurement can be scaled (service) to
the actual physical unit, eg voltage = volta [V], relative humidity =% RH, etc. In addition to the
presentation of the current value on the display, the function of recording the temperature history on
the SD card (service) is available, the measurement is recorded analogically to the temperature
(frequency 1 / 60s.).
Event history.
In order to view history of events in the system, press , then the numeric keypad will be displayed.
Enter the code and confirm #. If the sequence is correct, control panel will display the event memory,
line syntax with a single event::
RR.MM.DD GG.MM EVENT IN THE SYSTEM.
Navigation in history is done by buttons . Exit from the browse follows the button .

Str. 16
System operation.
© 2018 Ropam Elektronik
Editing codes.
To enter the code editing function in the system, press ,then the numeric keypad will be displayed.
Enter the code and confirm #. Following functions are available for user with the main code:
- new code (user) + permission setting,
- change of the main code,
- removing codes,
Following functions are available for other users:
- user code change.
System may have a maximum of 32 codes (users): 1 main and 31 users.
Main code has access to all functions, user codes have limited permissions.
Preview of system failures.
In order to view failure in system, indicated by a yellow LED; TROUBLE should be pressed .
"SYSTEM MALFUNCTIONS" will appear on the display.
Settings.
To enter the settings available to the user, press , then the "user" button. Enter the main code
and confirm #. The following settings are available:
- set the clock: set the clock and system date,,
- relay time: sets the relay operation time in the panel, monostable mode: min. 1s, bistable mode: 0s
- on / off chime: enables or disables chime signaling from zones in a given touch panel (chime
configuration is not remembered when the touch panel loses power),
- SMS reading: allows you to read the last SMS from the inbox (only that SMS is shown and displayed,
which does not have an access code and is not a system command, eg information from the GSM
network), reading an SMS deletes memory and signaling incoming message,
- LCD brightness: allows user to adjust the brightness of the display in screen saver mode or digital
photo frame function (factory settings 30%),
- service access: launch of the function allows access to the service through the service code for system
configuration for a period of 8 hours (access via touch panel).
Blocking zones.
To enter the function of blocking zones (detectors), press ; if a code is required, a numeric keypad
will be displayed, enter the code and confirm #. Blocking consists in selecting X at the selected input.
Output and confirmation is done via , exit from blocking without confirmation occurs via .