DT Research DT160 Assembly instructions

DT160
ENGLISH
BASIC OPERATION GUIDE
DT160
Embedded Controller/
System
Note: The actual package content may vary depending on the configuraon acquired.
ENGLISH 4
signage dtri com
DT Research, Inc.
2000 Concourse Drive, San Jose, CA 95131 hp://www.dtresearch.com
Copyright © 2012, DT Research, Inc. All Rights Reserved. DT Research is a registered trademark of DT Research, Inc.
INTRODUCTION
Thank you for acquiring the latest
addion to DT Research’s line of
Embedded Controller/ System
devices—the DT160, featuring a slim yet robust construcon
powered by the 1.5GHz x86 processor and providing complete soluons
for a variety of compung needs.
The DT160 supports major embedded operang systems as well as Microso® Windows® CE,
Windows® XP Embedded or Windows® XP Pro. The user is offered a choice of soware soluons
on a plaorm characterized by the following:
H
•igh-integraon and energy-efficient processor technology
R
•obust and fan-less construcon for quiet and reliable operaon
L
•ow-cost compung in compact and versale packaging
Package Contents
DT160
AC/DC Power Adapter
DVI-VGA Adapter
Basic Operaon Guide
4
3
3
2
21 1
BOG030512DT160ENG
SPECIFICATIONS
System
Processor 1.5GHz x86
GPU VIA CX700M
Memory (RAM) 512MB or 1GB
Storage 64MB to 16GB Flash; 160GB HDD
Operang Systems Microso® Windows® CE, Windows® XP Embedded, or
Windows® XP Pro for Embedded Systems
Display Resoluon Up to 1920 x 1080
Network Interface 10/ 100Mb BaseT LAN; Wi-Fi 802.11a/b/g (oponal)
Expansion Mini-PCI (internal); USB
Input/Output Ports
DVI-I; 12V DC-in jack; 3 Audio jacks (Microphone-in, Line-in,
Headphone-out jacks); 4 USB 2.0 ports; RJ45 connector for
Ethernet; Wi-Fi dipole antenna (oponal)
Power
AC/DC Adapter Input: 100 – 240V AC; Output: 12V DC
Mechanical
Enclosure Aluminum chassis; Magnesiumaluminum end-caps
Dimensions (H x W x D) 1.7 x 5.5 x 5.1 in/ 43 x 140 x 130 mm
Weight 1.2 lbs/ 544 g
Environmental
Regulatory FCC Class B, CE, C-Tick, UL, RoHS compliant
Temperature Operaon: 0°C - 40°C; Storage: -20°C - 60°C
Humidity 0% - 90% non-condensing
* Specificaons subject to change without noce.

DT160
ENGLISH 23ENGLISH
THE DT160
Rear ViewFront View
Powering ON and OFF
The Power Buon is located in the front of the DT160. The Power Buon may be configured to
behave differently depending on the operang soware. In general, to turn the DT160 on, push
and release the Power Buon on the front bezel. The adjacent power LED will be lit (blue) and the
corresponding interface will be displayed on the display monitor.
To turn offthe device, again depending on soware operang system, push and release the Power
Buon or use a soware shutdown interface.
In the event of system lockup, the Power Buon may be used to perform a reset on the device. To
do that, push and hold the Power Buon for at least 4 seconds. The system will shut down and all
unsaved work may be lost. Pushing on the Power Buon again will restart the device.
Device Ports
The DT160 features an opmal set of I/O ports while preserving the compact size of the structure.
The DVI, Network (10/100 BaseT Ethernet), and Power ports are supplemented by a set of four USB
2.0 and three Audio ports.
Through its USB ports, the DT160 supports a wide range of USB-based peripherals. These
peripherals are applicable in providing the means for soware installaon, applicaon storage, data
storage, and system soware recovery and updates.
Memory and Storage
The DT160 may be available in storage configuraons ranging from 4GB to 16GB of flash memory.
Depending on base soware configuraon, the user may use the internal flash memory of the
DT160 for user’s installed soware and storage. The user may also supplement storage space with
USB-based peripherals such as flash disks, disk drives, etc. RAM capacity is 1GB.
Opons
The DT160 is designed to work with a range of custom and off-the-shelf opons to enhance its
applicability for various deployments.
USB-to-Serial and USB-to-PS/2 adapters•
Internal mini-PCI wireless LAN (WLAN) adapters•
Short DVI cable for connecon to mounted display•
External bracket for mounng the DT160 to VESA adapters and•
LCD monitors (see mounng process below)
It is quite simple to mount the DT160 to VESA adapters or LCD monitors using the external
mounng bracket.
Precauons
Always exercise care when operang and handling the DT160.•
Never disassemble any poron of the enclosure. It will void any product warranty on the DT160.•
Do not use any AC/DC adapter other than the one provided with the device or acquired from the•
manufacturer or its partners.
In the unlikely event that smoke, abnormal noise, or strange odor is present, immediately power•
down the DT160 and disconnect all power sources. Please report the problem to your device
provider immediately.
USB 2.0 (2)
Ethernet port
DVI-I port
DC-in
E
G
F
H
A
A
B
C
C
D E F G H
D
B
Audio jacks
Power indicator
Power buon
USB 2.0 (2)