DualLite LZ Series User manual

Final Assembly
Energize unit.
Charge a minimum of 24 hours
prior to testing.
4.
Aim lamp heads towards center of unit and
dress wires neatly to prevent pinching.
1.
➤
2.
Align housing slots over back plate tabs.
Pivot housing
and snap
closed.
3.
Press test switch and hold. Aim lamp
heads for proper light distribution.
5.
TROUBLE SHOOTING
AC-On Light does not illuminate
• Check AC wiring connections.
Emergency lamps do not work
• Battery is disconnected. Connect red
lead from PC board to positive (+) battery
terminal and yellow lead from PC board
to negative (–) battery terminal and charge
before testing.
• Check wiring connections.
MAINTENANCE
Dual-Lite units should be tested and maintained
in accordance with National Electrical Code and
NFPA 101 Life Safety Code requirements. It is
recommended that emergency lighting units be
tested for 30 seconds once a month and for 90
minutes once a year.
RECYCLING INFORMATION
All thermoplastic parts are recyclable.
All cartons contain recycled materials.
Please recycle.
NOTICE:
Units contain rechargeable batteries which must
be recycled or disposed of properly.
LAMP REPLACEMENT
CAUTION: Halogen lamps operate at high tem-
peratures. Allow defective lamp to cool completely
before attempting replacement.
1. Remove plastic lamp retaining ring.
2. Pull defective lamp from lighting head assembly
and unplug lamp from socket.
3. Plug replacement lamp into socket and install
lamp into lighting head assembly.
4. Re-install lamp retainer ring (at side towards
lamp).
2-pin lamp socket
Retaining ring
MR-16 halogen
lamp
LZ High Capacity Series
Emergency Lighting Units
Installation Instructions
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should always be followed
including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
1. Do not use outdoors.
2. Do not mount near heaters or hot surfaces.
3. Equipment should be mounted in locations and at heights where it will not readily be
subjected to tampering by unauthorized personnel.
4. The use of accessory equipment not authorized by the manufacturer may cause an
unsafe condition.
Caution: Halogen cycle lamps are used in this equipment. To avoid shattering: Do not op-
erate lamp in excess of rated voltage, protect lamp against abrasion and scratches and
against liquids when lamp is operating, dispose of lamp with care.
5. Do not use this equipment for other than its intended purpose.
6. Service of this equipment should be performed by qualied service personnel.
SAVE THESE INSTRUCTIONS
Matching Remote Lighting
Fixtures
1. Carefully size wire
conductors from
emergency
unit to remote
xture(s) using a
voltage drop table.
2. Remove appropriate
knockouts in remote
xture mounting plate, feed
conductors through center hole.
3. Mount plate to approved electrical box using
screws supplied with box.
4. Make connections to xture lamp leads using
wire nuts or crimp connectors.
5. Push connectors back through hole in mount-
ing plate into electrical box.
6. Orient xture in desired position (xtures can
be rotated in 900increments to four positions).
7. Set xture on backplate and tighten lock-
ing screws. Aim lighting head(s) by rotating
eyeball to desired position.
Note:
Twin head remote xtures can
be mounted horizontally or
vertically for more accurate
illumination.
Hubbell Lighting, Inc. Life Safety Products • www.dual-lite.com
Copyright© Hubbell Lighting, Inc., All Rights Reserved • Specifications subject to change without notice.
Printed in U.S.A. 0603115 C 9/08
Halogen cycle lamps operate at high temperatures.
Do not store or place ammable materials near lamp.
Warning:
This product contains chemicals known to the state of California to cause cancer, birth defects, and/or other reproductive
harm. Thoroughly wash hands after installing, handling, cleaning, or otherwise touching this product.

LZ SERIES INSTALLATION INSTRUCTIONS
Connect building wires to transformer leads.
• Black and white wires for 120V
(Use wire nut to cap off red wire)
• Red and white wires for 277V
(Use wire nut to cap off black wire)
• Green wire to building ground
4.
Remove keyhole slots ➀and lower
mounting hole ➁knockouts in back plate.
1.
Secure backplate to
wall through keyhole
slots ➀and lower
mounting hole ➁
using
appropriate
fasteners.
Note:
Use
fasteners
with a
minimum
pullout
rating of
20 pounds.
3.
Wall Mount – Back Power Feed Wall Mount – Surface Wiring (Top Power Feed Only)
Feed wires
through center
K.O. and mount
back plate over
electrical box.
2.
IMPORTANT: Security screw is not mandatory but may be installed if desired.
No. 8 security screw is shipped in cover boss ➂. Use pointed tool to remove K.O. at bottom
center of unit chassis. After closing unit, install security screw through bottom K.O. and tighten.
Connect remote lighting
load to distribution board
5.
Secure conduit (or surface
raceway) to K.O. and feed
wires.
3.
Remove conduit entry K.O. at top ange of back plate plus
keyhole slots ➀ and lower mounting hole ➁ knockouts
1.
2.
Secure backplate to wall
through keyhole slots ➀and
lower mounting hole ➁
using appropriate
fasteners.
Note:
Use fasteners
with a minimum
pullout rating of
20 pounds.
To complete installation, see Final Assembly instructions on back page.
Connect red lead from PC board to (+) battery terminal
and yellow lead from PC board to negative (–) battery
terminal. Slide battery(s) onto mounting shelf and secure
with velcro strap
6.
Connect building wires to transformer leads.
• Black and white wires for 120V
(Use wire nut to cap off red wire)
• Red and white wires for 277V
(Use wire nut to cap off black wire)
• Green wire to building ground
4.
IMPORTANT: Security screw is not mandatory but may be installed if desired.
No. 8 security screw is shipped in cover boss ➂. Use pointed tool to remove K.O. at bottom
center of unit chassis. After closing unit, install security screw through bottom K.O. and tighten.
Connect remote lighting
load to distribution board
5.
To complete installation, see Final Assembly instructions on back page.
Connect red lead from PC board to (+) battery terminal
and yellow lead from PC board to negative (–) battery
terminal. Slide battery(s) onto mounting shelf and secure
with velcro strap
6.
➀
➁
➀
➀
➁
➀
➂
➂