Alderon Industries Sump Advisor 2000514 User manual

USER GUIDE
PART NUMBERS:
Sump Advisor™2-Zone Alarm and Sensor
Rated Type 1, Indoor Alarm Panel (use with Alderon™ VertiMAC™ series)
2000514 2000558 2000559
2000560 2000561
Alderon Industries™
Pat. No. 10,794,379

Contents
Introduction................................................................................................................................................................. 3
Safety Guidelines ................................................................................................................................................... 3
Product Included .................................................................................................................................................... 4
Features ................................................................................................................................................................. 5
Installation of Sump Advisor™ Alarm Panel ............................................................................................................... 6
9VDC Battery Backup ........................................................................................................................................ 6, 7
Mounting Alarm Panel............................................................................................................................................ 8
Wiring Auxiliary Dry Contacts .......................................................................................................................... 9, 10
Installation of Sump Advisor™ Sensor ..................................................................................................................... 10
Installation of VertiMAC™ Pump Switch (sold separately) ............................................................................................ 11
Pump Differential.................................................................................................................................................. 11
Mounting Pump Switch .............................................................................................................................12, 13, 14
Connecting Power to VertiMAC™ and Sump Advisor™........................................................................................... 15
VertiMAC™ Pump Switch with Sump Advisor™ Sensor...................................................................................... 15
Sump Advisor™ Alarm Panel............................................................................................................................... 15
Testing ................................................................................................................................................................ 16, 17
Assembly and Maintenance ..................................................................................................................................... 18
Additional Assembly and Product Information ......................................................................................... 18, 19, 20
Maintenance................................................................................................................................................... 20, 21
General Operation.................................................................................................................................................... 22
Sump Pump ......................................................................................................................................................... 22
Sump Pump with Indoor/Outdoor LED Strobe Beacon ........................................................................................ 23
Sump Pump with Auto Dialer ............................................................................................................................... 24
Sump Pump with Battery Backup ........................................................................................................................ 25
Sump Pump with Battery Backup and Auto Dialer............................................................................................... 26
Troubleshooting ........................................................................................................................................................ 27
Specications ........................................................................................................................................................... 28
Warranty Information ................................................................................................................................................ 29
Company Information ............................................................................................................................................... 32
Sump Advisor™ 2-Zone Alarm and Sensor - USER GUIDE

Alderon Industries™ - Leading Edge Control Products | 3
Sump Advisor™ 2-Zone Alarm and Sensor - USER GUIDE
Introduction
The Sump Advisor™ 2-Zone Alarm is an indoor rated alarm panel, powered by a standard 120VAC wall outlet. The included Sump
Advisor™ Sensor is attached to the top of the VertiMAC™ VM-Series pump switch (sold separately) and connected to the terminal
block on the alarm panel. The alarm panel and sensor can only be used with the Alderon™ VertiMAC™ pump switch series, a
oat operated pump switch system, typically used in sump pump applications or situations where a regular pump switch cannot
operate due to limited space. The innovative Sump Advisor™ sensor integrates high level alarm and pump run switches that are
connected to the Sump Advisor™ alarm panel. The alarm panel has a 9-volt battery backup (customer supplied) and auxiliary dry
contacts for high level alarm and pump run status that can be connected to a building automation system (BAS) or auto dialers.
Safety Guidelines
Before proceeding with the installation or operation of this product, read all instructions thoroughly, as well as complying with
all federal, state and local codes, regulations, and practices. This product must be installed by qualied personnel familiar with
all applicable local electrical and mechanical codes. Refer to the National Electrical Code (NFPA 70). Failure to properly install
and test this product can result in personal injury or equipment malfunction.
1. DISCONNECT POWER when installing or servicing the product. Failure to disconnect all power sources could result in
serious injury or death.
2. NEVER enter a ooded space without proper Personal Protective Equipment (PPE). Always wear dielectric rubber boots
and other applicable protective equipment when water is on the oor and you must service an energized pump, alarm
system, or product.
3. DO NOT enter the water if the water level is higher than that of the protection your PPE offers or if your PPE is not
watertight.
4. DO NOT use this product with or near ammable liquids.
5. DO NOT install this product in locations classied as hazardous or in explosive atmospheres as dened by any applicable
electrical safety code.
WARNING

4 | Alderon Industries™ - Leading Edge Control Products
Sump Advisor™ 2-Zone Alarm and Sensor - USER GUIDE
Product Included
(1) Sump Advisor™ 2-Zone Alarm Panel
The alarm panel provides local high level alarm and pump run
indication of the VertiMAC™ pump switch (sold separately).
(2) Sump Advisor™ Sensor
The sensor attaches on top of the VertiMAC™ VM-Series pump
switch and connects to the Sump Advisor™ alarm panel.
ADDITIONAL OPTIONS:
The standard product will include: (1) Sump Advisor™ 2-Zone Alarm Panel and (1) Sump Advisor™ Sensor.
1
2
3
5
4
(120VAC Piggyback Plug Model Shown)
(3) VertiMAC™ Pump Switch, VM-Series
The VertiMAC™ is a oat operated pump switch for sump pump
applications, includes a pipe clamp bracket and stainless steel
pipe clamp. The power cable is available in 120/240VAC bare
lead (no plug), 120VAC piggyback plug, or 240VAC piggyback
plug models. Rated 13 Amps.
(4) Indoor/Outdoor LED Strobe Beacon
The remote strobe beacon is connected to the Sump Advisor™
alarm panel and provides a secondary indoor or outdoor high
level alarm indication.
(5) Auto Dialer
The auto dialer is connected to the alarm auxiliary dry contacts
on the Sump Advisor™ alarm panel to monitor high level alarm
status. When the contacts close on the alarm panel, it activates
the input of the auto dialer sending a voice message to
programmed number(s).

Alderon Industries™ - Leading Edge Control Products | 5
Sump Advisor™ 2-Zone Alarm and Sensor - USER GUIDE
Features
Refer to the illustration below to reference the feature descriptions provided.
(1) Power On LED - A green LED illuminates on the front of the
alarm panel to indicate the power is on.
(2) High Sump LED - During an alarm condition, the red high
sump alarm LED will illuminate on the front of the alarm panel.
(3) Pump Run LED - When the pump switch activates the pump,
the green LED will illuminate on the front of the alarm panel for
pump run indication.
(4) Alarm Buzzer - The alarm buzzer will annunciate in addition
to the visual indication provided by the red LED during an alarm
condition.
(5) Alarm Test Pushbutton - Press the pushbutton to test the
alarm to ensure proper operation. The buzzer should annunciate,
high sump alarm LED should illuminate, and auxiliary contacts
should activate.
(6) Alarm Silence Pushbutton - Press the pushbutton to silence
the buzzer during an alarm condition. The alarm LED remains
illuminated until the alarm condition has been cleared and the
alarm panel will auto reset for the next alarm cycle.
(7) Terminal Block - Connect the Sump Advisor™ sensor to the
alarm panel for local high level alarm and pump run indication.
(8) Auxiliary Contacts - Interface with an external device
including building automation systems and phone dialers. The
contacts (normally open) are rated 24VDC/24VAC, 50/60 Hz, and
100mA maximum.
(9) Battery Backup - Install a 9VDC battery (not included) for
battery backup during power outages.
(10) Panel Compartment - Wire connector for 9VDC battery
(backup power), auxiliary dry contacts, and access cover with
break away tabs for routing wire.
(11) Power Supply (not shown) - A 120VAC, 60 Hz, 5-foot power
cord connects to a standard wall outlet.
(12) Mounting Holes - Two mounting holes are included on the
alarm panel enclosure to securely fasten in the desired mounting
location.
(13) Sensor Housing - Internal signaling components are
protected within housing to ensure a waterproof sensor.
(14) Sensor Cable - The cable sends a signal from the sensor to
the alarm panel. Rated 24VDC, 100mA maximum, 22 AWG, and
3-conductor.
(15) Mounting Tabs - Three tabs are located on the bottom of the
sensor housing to attach and secure the sensor to the top of the
VertiMAC™ pump switch.
(16) Float Basket - Houses the high level oat and protects from
obstructions in the monitoring area.
(17) Float - Rises and lowers inside the oat basket based on the
liquid level in the monitoring area.
(18) Locking Tabs (not shown) - Two tabs are located on the
bottom of the sensor housing which secures the oat basket in
place.
1
2
3
4
5 6
7
89
10
10
12
12
13
14
15
16
17
15

6 | Alderon Industries™ - Leading Edge Control Products
Sump Advisor™ 2-Zone Alarm and Sensor - USER GUIDE
Installation of Sump Advisor™ Alarm Panel
DISCONNECT ALL POWER SOURCES WHEN INSTALLING OR SERVICING THIS PRODUCT. FAILURE TO
TURN OFF ALL POWER SOURCES COULD RESULT IN SERIOUS INJURY OR DEATH.
ALARM PANEL MUST BE MOUNTED INDOORS. FOR OUTDOOR APPLICATIONS CONSULT FACTORY.
9VDC Battery Backup
STEP 1: REMOVE ACCESS COVER
To install or replace the battery for the backup power feature, remove the alarm panel access cover.
STEP 2: INSTALL/REPLACE BATTERY
Install the 9VDC battery matching the terminals of the wire connector on the alarm panel to the terminals on top of the battery.
Place the battery inside the top panel compartment to secure and ensure proper operation of the backup power feature.

Alderon Industries™ - Leading Edge Control Products | 7
Sump Advisor™ 2-Zone Alarm and Sensor - USER GUIDE
STEP 3: TEST INSTALLATION
After proper installation of the battery, the green power LED
should illuminate to indicate the alarm panel is powered on. If
the green LED does not illuminate, the battery was not properly
installed. Check connection before proceeding.
Press and hold the alarm test pushbutton to activate the alarm
function. The buzzer should annunciate and the red high sump
LED should illuminate.
9VDC Battery Backup (continued)
STEP 4: REPLACE ACCESS COVER
After the alarm panel battery backup power feature has been tested and determined to be working properly, replace the access
cover if the auxiliary dry contacts are not used. If connecting wires to the auxiliary dry contacts, leave the access cover off until
step 1 on page 9 is completed.
Power
Alarm
Test
Alarm
Silence
High
Sump
Pump
Run

8 | Alderon Industries™ - Leading Edge Control Products
Sump Advisor™ 2-Zone Alarm and Sensor - USER GUIDE
Mounting Alarm Panel
STEP 1: DETERMINE MOUNTING LOCATION
Determine the mounting location for the alarm panel, make sure the power outlet (120VAC, 50/60 Hz) is within ve feet (5′) of the
alarm panel. The power outlet should be on a separate circuit breaker from any other device and not on a switched receptacle
to maintain power integrity.
CAUTION: Do not connect power to the alarm panel until the installation of both the Sump Advisor™ alarm panel and Sump
Advisor™ sensor are completed.
STEP 2: MOUNT ALARM PANEL
Hold the alarm panel in the desired mounting location, mark the
drill hole locations. Once marked, drill pilot holes for screws (not
included) and use wall mount anchors (not included) if necessary.
Place alarm panel in the mounting location, adjust until the pilot
holes are lined up with the enclosure and fasten screws to secure
the alarm panel in place.
5 Feet Maximum

Alderon Industries™ - Leading Edge Control Products | 9
Sump Advisor™ 2-Zone Alarm and Sensor - USER GUIDE
Wiring Auxiliary Dry Contacts
STEP 1: TERMINAL BLOCK CONNECTIONS
If connecting to an existing alarm security system or building automation system (BAS), leave the positive (+) and negative (-)
terminals open and use 18 gauge 2-conductor wire to connect the existing product to terminals 2A, 2B, 1A, and 1B.
If connecting to an Alderon™ auto dialer using the supplied 4-conductor wire: connect red wire to positive (+) terminal, black
wire to negative (-) terminal, yellow wire to terminal 1A, and white wire to terminal 1B.
When the VertiMAC™ pump switch is activated, it will turn the pump on closing the pump auxiliary dry contacts 2A and 2B on
the Sump Advisor™ alarm panel. When the Sump Advisor™ sensor high level alarm oat is activated, it will close the alarm
auxiliary dry contacts 1A and 1B on the Sump Advisor™ alarm panel. See step 2 below for removing access cover break away
tabs and step 3 on page 10 for replacing access cover of the alarm panel after wiring for the auxiliary dry contacts is completed.
2A 2B 1A 1B
AUXILIARY DRY CONTACTS:
Terminals “+” (positive) and “-” (negative)
11.1VDC, 100mA power supply for external equipment
Terminals 2A and 2B
Zone 2 (Pump Run)
Normally Open
Terminals 1A and 1B
Zone 1 (High Sump)
Normally Open
Class 2, 24VDC/VAC (50/60 Hz)
100 Milliamps Maximum
Note: The auxiliary dry contacts of the alarm panel
are normally open ONLY.
STEP 2: REMOVING ACCESS COVER BREAK AWAY TABS
After the access cover has been removed from the alarm panel,
use a needle nose pliers (not included) to remove the desired
break away tab(s) from the access cover. Lightly pull and twist
off tab(s).
21 3

10 | Alderon Industries™ - Leading Edge Control Products
Sump Advisor™ 2-Zone Alarm and Sensor - USER GUIDE
STEP 3: REPLACE ACCESS COVER
After the wiring is completed and the desired break away tab(s) have been removed, replace the access cover and run wire(s)
through the knockout(s). Route all wires away from sharp objects and internal components when replacing the access cover.
Wiring Auxiliary Dry Contacts (continued)
Wiring Sump Advisor™ Sensor to Sump Advisor™ Alarm Panel
STEP 1: SUMP SENSOR WIRE CONNECTIONS
Connect the normally open Sump Advisor™ sensor (rated 24VDC, 100mA maximum) to the Sump Advisor™ alarm panel for local
high level alarm and pump run indication from the VertiMAC™ pump switch. Connect white wire to terminal W, red wire to terminal
R, and black wire to terminal B.
Installation of Sump Advisor™ Sensor
DISCONNECT ALL POWER SOURCES WHEN INSTALLING OR SERVICING THIS PRODUCT. FAILURE TO
TURN OFF ALL POWER SOURCES COULD RESULT IN SERIOUS INJURY OR DEATH.
WRB
TERMINAL BLOCK CONNECTIONS:
Sensor Wire Alarm Panel Terminal
White W = Common
Red R = High Level Alarm
Black B = Pump Run
White
Red
Black

Alderon Industries™ - Leading Edge Control Products | 11
Sump Advisor™ 2-Zone Alarm and Sensor - USER GUIDE
Installation of VertiMAC™ Pump Switch, VM-Series (sold separately)
DISCONNECT ALL POWER SOURCES WHEN INSTALLING OR SERVICING THIS PRODUCT. FAILURE TO
TURN OFF ALL POWER SOURCES COULD RESULT IN SERIOUS INJURY OR DEATH.
Pump Differential
STEP 1: DETERMINING PUMP DIFFERENTIAL
Determine the pump differential and move the rubber grommet on the actuator rod to achieve the desired range. After the pump
switch installation is complete, perform testing to achieve actual pumping differential.
Maximum Differential: Move the rubber grommet to the bottom of the actuator rod to create the largest pump differential, which
is six inches (6.0″).
Minimum Differential: Move the oat and rubber grommet to the top of the actuator rod to create the smallest pump differential,
which is one and a half inches (1.5″).
Note: Leave approximately one eighth inch (1/8″) of space between the rubber grommet and the bottom of the actuator rod to
achieve the maximum differential. Placing the rubber grommet at the bottom of the rod could cause the grommet and oat to
separate from the actuator rod.
(Pump Activated)
(Pump Deactivated)
Maximum (6.0″)
Pump Differential
(Pump Activated)
(Pump Deactivated)
Minimum (1.5″)
Pump Differential

12 | Alderon Industries™ - Leading Edge Control Products
Sump Advisor™ 2-Zone Alarm and Sensor - USER GUIDE
Mounting Pump Switch
STEP 1: RELEASE PIPE CLAMP
The pipe clamp comes secured into the fastener (1A) and must
be released (1B) using either a slotted screwdriver or 5/16″ nut
driver on the fastener nut.
1A
1B
STEP 2: INSTALL PIPE CLAMP
Slide the pipe clamp through the loop on the pre-installed pipe
clamp bracket of the VertiMAC™ pump switch.
Note: Make sure the pipe clamp is positioned as shown in the
diagram when installing so excess portion of the clamp exits the
fastener away from the pump switch.
(120VAC Piggyback Plug Model Shown)

Alderon Industries™ - Leading Edge Control Products | 13
Sump Advisor™ 2-Zone Alarm and Sensor - USER GUIDE
Mounting Pump Switch (continued)
STEP 3: MOUNTING TO PIPE
Attach the pipe clamp to pipe at the approximate mounting level
and tighten using the fastener nut. Make sure to keep all cables
and wires away from the oat while mounting.
Note: Do not completely secure pipe clamp and VertiMAC™
pump switch to the pipe until the off level has been determined.
See step 4 nal mounting location on page 14.
CAUTION: The VertiMAC™ pump switch MUST be mounted in
the vertical position. Mounting the pump switch at an angle will
result in the switch not functioning properly. Perform a quick test
by lifting the oat up and down to ensure the switch is working.
Do not connect power to the pump switch until the installation
of both the Sump Advisor™ sensor and Sump Advisor™ alarm
panel are completed.
(120VAC Piggyback Plug Model Shown)

14 | Alderon Industries™ - Leading Edge Control Products
Sump Advisor™ 2-Zone Alarm and Sensor - USER GUIDE
Mounting Pump Switch (continued)
STEP 4: FINAL MOUNTING LOCATION
After the off level of the VertiMAC™ pump switch has been determined, check to make sure level is above the intake to the
pump to prevent dry cycling. Refer to the instructions that came with the pump for complete operation information. Once the
pump switch is in the nal mounting location, securely fasten the pipe clamp and VertiMAC™ pump switch to maintain an
accurate pumping range.
PUMP
VertiMAC™ Pump Switch
and
Sump Advisor™ Sensor
VertiMAC™
Off Level
Pump
Intake

Alderon Industries™ - Leading Edge Control Products | 15
Sump Advisor™ 2-Zone Alarm and Sensor - USER GUIDE
Connecting Power to VertiMAC™ and Sump Advisor™
Make sure the installation process is completed and there are no cables or wires to interfere with the operation of the oat on
the VertiMAC™ pump switch.
VertiMAC™ Pump Switch with Sump Advisor™ Sensor
POWER SOURCE
G L2/N L1
WIRE USING
JUNCTION BOX
120/240 VAC
G
BLACK
WHITE
LOAD
G L2/N L1
POWER CORD MODEL ONLY
The alarm panel should be installed, wired to the Sump Advisor™ sensor, and the power outlet (120VAC, 50/60 Hz) is within
ve feet (5′) of the alarm panel. The power outlet should be on a separate circuit breaker from any other device and not on a
switched receptacle to maintain power integrity. See step 1 and step 2 on page 8 for mounting alarm panel installation.
Sump Advisor™ Alarm Panel
PIGGYBACK PLUG MODELS
1) Plug the male end of the piggyback plug on the VertiMAC™
pump switch power cable into a standard wall outlet or power
receptacle that matches the voltage of the pump switch (A).
2) Plug the male end of the pump power cable into the female
end of the piggyback plug on the VertiMAC™ pump switch
power cable (B).
BARE LEAD MODELS
1) Connect bare lead wires from the VertiMAC™ pump switch
power cable to terminal inputs in a junction box as shown in
the diagram.
WARNING: In 240VAC installations, one side of the line going to the load is
always HOT. This condition exists if the switch is on or off. Install double pole
disconnect on all 240VAC circuits.
B
A
VertiMAC™ Pump Switch
Piggyback Plug
Power Cable
Pump
Power Cable
(120VAC Example Shown)

16 | Alderon Industries™ - Leading Edge Control Products
Sump Advisor™ 2-Zone Alarm and Sensor - USER GUIDE
Testing
STEP 1: SYSTEM CHECK
Prior to testing, make sure the installation process is complete. Check to make sure there are no wires to interfere with the
operation of the oat on the VertiMAC™ pump switch, the VertiMAC™ pump switch has been connected to a power supply,
the Sump Advisor™ sensor has been wired to the Sump Advisor™ alarm panel, and the green power LED is illuminated on the
Sump Advisor™ alarm panel.
STEP 2: TEST PUMP OFF
When the actuator rod on the VertiMAC™ pump switch is in the down position (deactivated), the pump should be off and the
green power LED should be the only LED illuminated on the Sump Advisor™ alarm panel.
STEP 3: TEST PUMP ON
When the actuator rod on the VertiMAC™ pump switch is in the up position (activated), the pump should be on and the green
pump run LED should be illuminated on the Sump Advisor™ alarm panel.
Activation Level
Deactivation Level
Pumping
Range
Power
Alarm
Test
Alarm
Silence
High
Sump
Pump
Run

Alderon Industries™ - Leading Edge Control Products | 17
Sump Advisor™ 2-Zone Alarm and Sensor - USER GUIDE
Testing (continued)
STEP 4: TEST HIGH LEVEL ALARM OFF
When the actuator rod on the VertiMAC™ pump switch is in the up position (activated), the pump should be on, the green pump
run LED should be illuminated, the pump run auxiliary dry contacts will activate, and the red high sump LED should be off on
the Sump Advisor™ alarm panel for a normal condition.
STEP 5: TEST HIGH LEVEL ALARM ON
When the actuator rod on the VertiMAC™ pump switch is in the up position (activated), the pump should be on, the green pump
run LED should be illuminated, and the pump run auxiliary dry contacts will activate on the Sump Advisor™ alarm panel. When
the water level rises activating the oat on the Sump Advisor™ sensor, the red high sump LED should illuminate, the buzzer
should annunciate, and the alarm auxiliary dry contacts will activate on the Sump Advisor™ alarm panel for an alarm condition.
Pressing the alarm silence pushbutton will silence the buzzer while the red high sump LED remains illuminated. When the alarm
condition is cleared, the system will automatically reset itself for the next alarm cycle.
STEP 6: PUMPING RANGE
After testing is complete, the pumping range can be adjusted by moving the rubber grommet up or down the actuator rod on
the VertiMAC™ pump switch to achieve the desired pump differential. See step 1 determining pump differential on page 11.
WARNING: If making any adjustments to the VertiMAC™ Sump Advisor™ system after testing has been completed, make sure to disconnect
all power sources before servicing the product.
Deactivation
Level
Activation
Level
Activation
Level
Approximately
4.0″
Power
Alarm
Test
High
Sump
Pump
Run
Alarm
Silence

18 | Alderon Industries™ - Leading Edge Control Products
Sump Advisor™ 2-Zone Alarm and Sensor - USER GUIDE
The VertiMAC™ pump switch comes pre-assembled with the actuator rod, oat, and pipe clamp bracket installed. The Sump
Advisor™ sensor is installed on top of the pump switch housing. The pumping differential is set at the maximum range (6.0″). If
adjustments or servicing is required, use this section for additional instructions on the pump switch and sensor.
Additional Assembly and Product Information
Assembly and Maintenance
MOUNTING PIPE CLAMP BRACKET
Place the pipe clamp bracket on the bottom of the VertiMAC™
pump switch housing and line up the holes. Use a #2 phillips
head screwdriver to securely fasten the bracket to the housing
with provided screws.
INSERTING ACTUATOR ROD
Slide the actuator rod arm upward into the front of the VertiMAC™
pump switch housing, positioned so the notch on the actuator arm
matches the side of the housing with the hole. If the actuator rod
arm is inserted in the correct position, the pump switch housing
should make a clicking sound as the rod slides up and down.
ACTUATOR PIN PLACEMENT
Once the actuator rod arm has been placed into the VertiMAC™
pump switch housing in the up position, insert the actuator pin
into the small hole on the left side of the housing until it snaps
in place.

Alderon Industries™ - Leading Edge Control Products | 19
Sump Advisor™ 2-Zone Alarm and Sensor - USER GUIDE
RUBBER GROMMET AND FLOAT PLACEMENT
Slide the oat onto the actuator rod, positioned so the text “This
Side Up” on the oat is facing up and then slide the rubber
grommet onto the actuator rod to secure the oat on the rod.
The pump differential can be adjusted by sliding the rubber
grommet up and down the actuator rod. See step 1 determining
pump differential on page 11.
PUMP SWITCH: PUMP OFF and PUMP ON
When the actuator rod is in the down position (deactivated), the
mechanism inside the VertiMAC™ pump switch housing turns
the pump off (A).
When the actuator rod is in the up position (activated), the
mechanism inside the VertiMAC™ pump switch housing turns
the pump on (B).
Additional Assembly and Product Information (continued)
BA
THIS SIDE UP
THIS SIDE UP
Adjustable
Rubber Grommet
(off level)

20 | Alderon Industries™ - Leading Edge Control Products
Sump Advisor™ 2-Zone Alarm and Sensor - USER GUIDE
SUMP SENSOR: HIGH LEVEL FLOAT DEACTIVATED
When the high level alarm oat on the Sump Advisor™ sensor
is in the down position (deactivated), the Sump Advisor™ alarm
panel is also deactivated and in a normal condition.
Additional Assembly and Product Information (continued)
SUMP SENSOR: HIGH LEVEL FLOAT ACTIVATED
When the high level alarm oat on the Sump Advisor™ sensor
is in the up position (activated), it will send a signal activating
the Sump Advisor™ alarm panel to indicate an alarm condition.
Deactivation Level
Activation Level
Maintenance
DISCONNECT ALL POWER SOURCES WHEN INSTALLING OR SERVICING THIS PRODUCT. FAILURE TO
TURN OFF ALL POWER SOURCES COULD RESULT IN SERIOUS INJURY OR DEATH.
STEP 1: UNLOCK FLOAT BASKET
Unlock the oat basket with your hands, gently pulling outward
on the locking tabs and rotating counterclockwise.
If service of the high level alarm oat on the sump sensor is required, use this section for instructions on how to clean grime off
the oat or remove materials which may clog the oat basket.
Locking
Tab
Locking
Tab