Dukane 8420 User manual

Projector
8420 / 8421
User Manual
Thank you for purchasing this product. Please
read this manual before you operate your
projector. Save it for future reference.

1
Table of contents
Important safety
instructions .......................2
Introduction......................4
Projector features ................................. 4
Shipping contents................................. 5
Projector exterior view......................... 6
Controls and functions ......................... 7
Positioning your
projector..........................10
Choosing a location............................ 10
Projection dimensions........................ 11
Connection ......................12
Connecting a computer or monitor .... 13
Connecting Video source devices ...... 14
Operation ........................17
Starting up the projector..................... 17
Using the menus................................. 18
Utilizing the password function ......... 19
Switching input signal........................ 21
Adjusting the projected image ........... 22
Magnifying and searching for details. 23
Selecting the aspect ratio ................... 24
Optimizing the image......................... 26
Setting the presentation timer ............ 29
Hiding the image................................ 30
Locking control keys.......................... 30
Freezing the image ............................. 30
Operating in a high altitude
environment ....................................... 31
Shutting down the projector............... 31
Menu operation .................................. 32
Maintenance ...................41
Care of the projector .......................... 41
Lamp information .............................. 42
Troubleshooting .............47
Specifications ..................48
Projector specifications...................... 48
Dimensions ........................................ 50
Timing chart ...................................... 51
Regulation Statements ...55
FCC statement ................................... 55
ICES-003 ........................................... 55
WEEE ................................................ 55
Copyright information...57
Warranty and
after-service ....................58
Entries and graphical symbols expla-
nation
The following entries and graphical symbols are
used for the manuals and the product as follows,
for safety purpose. Please know their meanings
beforehand, and heed them.
WARNING: This entry warns of a risk of
serious personal injury or even death.
CAUTION: This entry warns of a risk of
personal injury or physical damage.

2
Important safety instructions
Your projector is designed and tested to meet the latest standards for safety of information
technology equipment. However, to ensure safe use of this product, it is important that you
follow the instructions mentioned in this manual and marked on the product.
Safety Instructions
WARNING
1. Please read this manual before you operate your projector. Save it for future
reference.
2. Do not look straight at the projector lens during operation. The intense light beam
may damage your eyes.
3. Refer servicing to qualified service personnel.
4. Always open the lens shutter or remove the lens cap when the projector lamp is
on.
5. In some countries, the line voltage is NOT stable. This projector is designed to operate
safely within a mains voltage between 100 to 240 volts AC, but could fail if power
cuts or surges of ±10 volts occur. In areas where the mains voltage may fluctuate
or cut out, it is recommended that you connect your projector through a power
stabilizer, surge protector or uninterruptible power supply (UPS).
6. Do not block the projection lens with any objects when the projector is under
operation as this could cause the objects to become heated and deformed or even
cause a fire. To temporarily turn off the lamp, press BLANK on the projector or
remote control.
7. The lamp becomes extremely hot during operation. Allow the projector to cool for
approximately 45 minutes prior to removing the lamp assembly for replacement.
8. Never replace the lamp assembly or any electronic components unless the projector is
unplugged.
9. Do not place this product on an unstable cart, stand, or table. The product may fall,
sustaining serious damage.
10. Do not attempt to disassemble this projector. There are dangerous high voltages inside
which may cause death if you should come into contact with live parts. The only user
serviceable part is the lamp which has its own removable cover.
Under no circumstances should you ever undo or remove any other covers. Refer
servicing only to suitably qualified professional service personnel.
11. Do not place this projector in any of the following environments.
- Space that is poorly ventilated or confined. Allow at least 50 cm clearance from walls
and free flow of air around the projector.
- Locations where temperatures may become excessively high, such as the inside of a
car with all windows rolled up.
- Locations where excessive humidity, dust, or cigarette smoke may contaminate optical
components, shortening the projector's life span and darkening the picture.
- Locations near fire alarms
- Locations with an ambient temperature above 40°C / 104°F
- Locations where the altitudes are higher than 3000 m (10000 feet).

3
12. Do not block the ventilation holes. If the ventilation holes are seriously obstructed,
overheating inside the projector may result in a fire.
- Do not place this projector on a blanket, bedding or any other soft surface.
- Do not cover this projector with a cloth or any other item.
- Do not place inflammables near the projector.
13. Always place the projector on a level, horizontal surface during operation.
- Do not use if tilted at an angle of more than 10 degrees left to right, nor at angle of
more than 15 degrees front to back. Using the projector when it is not fully horizontal
may cause a malfunction of, or damage to, the lamp.
14. Do not stand the projector on end vertically. Doing so may cause the projector to fall
over, causing injury or resulting in damage to the projector.
15. Do not step on the projector or place any objects upon it. Besides probable physical
damage to the projector, doing so may result in accidents and possible injury.
16. Do not place liquids near or on the projector. Liquids spilled into the projector may
cause it to fail. If the projector does become wet, disconnect it from the power
supply's wall socket and call your local service center to have the projector serviced.
17. When the projector is under operation, you may sense some heated air and odor from
its ventilation grill. It is a normal phenomenon and not a product defect.
18. Do not use the security lock slot for transporting or installation. It should be used with
a commercially available theft prevention cable.
DUKANE CORP AV SERVICE DEPT
2900 Dukane Drive
St Charles, IL 60174
800-676-2487
Fax [phone]
[email protected]
http://www.dukane.com/av/service/

4
Introduction
Projector features
The projector integrates high-performance optical engine projection and a user-friendly
design to deliver high reliability and ease of use.
The projector offers the following features.
• Presentation timer for better control of time during presentations
• Supports 3D display
• Color Management allowing color adjustments to your liking
• Less than 0.5W power consumption when standby mode is saving
• Wall Color correction allowing projection on surfaces of several predefined colors
• Quick auto search speeding up the signal detecting process
• Multiple sets of preset modes providing choices for different projection purposes
• One-key auto-adjustment to display the best picture quality
• Digital keystone correction to correct distorted images
• Adjustable color management control for data/video display
• High brightness projection lamp
• Ability to display 1.07 billion colors
• Multi-language On-Screen Display (OSD) menus
• Switchable normal and economic modes to reduce the power consumption
• Component HDTV compatibility (YPbPr)
• The apparent brightness of the projected image will vary depending on the ambient
lighting conditions, selected input signal contrast/brightness settings, and is directly
proportional to projection distance.
• The lamp brightness will decline over time and may vary within the lamp manufacturers
specifications. This is normal and expected behavior.

5
Shipping contents
Carefully unpack and verify that you have all of the items shown below. If any of these
items are missing, please contact your place of purchase.
Standard accessories
The supplied accessories will be suitable for your region, and may differ from those
illustrated.
Optional accessories
1. Replacement lamp: DT01461
Projector Power Cord VGA Cable
Multi-language user
manual CD User manual Remote Control & Battery
GOST-R Declaration

6
Projector exterior view
1. Control panel
(See "Control panel" on page 7 for
details.)
2. Lamp cover
3. Vent (heated air exhaust)
4. Front elevator foot
5. Zoom ring
6. Focus ring
7. Vent (cool air intake)
8. Front IR remote sensor
9. Projection lens
10. AC power cord inlet
11. CONTROL port
12. SERVICE port
13. HDMI port
14. COMPUTER IN1 port
15. COMPUTER IN2 port
16. MONITOR OUT port
17. S-VIDEO port
18. VIDEO port
19. AUDIO IN port
20. AUDIO OUT port
21. Security lock slot
22. Rear elevator foot
WARNING
• THIS APPARATUS MUST BE EARTHED.
• When installing the unit, incorporate a readily accessible disconnect device in the fixed wiring,
or connect the power plug to an easily accessible socket-outlet near the unit. If a fault should
occur during operation of the unit, operate the disconnect device to switch the power supply
off, or disconnect the power plug.
1
2
3
4
5
6
7
8
9
Front/upper side
10
15
21
22
11 12 13 14 18
17 19 2016
Rear/lower side

7
Controls and functions
Control panel
1. TEMPerature indicator light
Lights up red if the projector's temperature
becomes too high.
2. LAMP indicator light
Indicates the status of the lamp. Lights up
or flashes when the lamp has developed a
problem.
3. Keystone/Arrow keys ( Up,
Down)
Manually corrects distorted images
resulting from an angled projection.
4. Left
Used to hide the screen picture.
5. MODE/ENTER
Selects an available picture setup mode.
Enacts the selected On-Screen Display
(OSD) menu item.
6. SOURCE
Displays the source selection bar.
7. POWER indicator light
Lights up or flashes when the projector is
under operation.
8.
Toggles the projector between standby
mode and on.
9. Right
Activates panel key lock.
When the On-Screen Display (OSD)
menu is activated, the #3, #4, and #9 keys
are used as directional arrows to select the
desired menu items and to make
adjustments.
10. MENU
Turns on the On-Screen Display (OSD)
menu. Goes back to previous OSD menu,
exits and saves menu settings.
1
2
3
4
5
6
7
8
9
10
3
I
I

8
Remote control
1.
Toggles the projector between standby
mode and on.
2. MENU/EXIT
Turns on the On-Screen Display
(OSD) menu. Goes back to previous
OSD menu, exits and saves menu
settings.
3. FREEZE
Freezes the projected image.
4. Left
5. MODE/ENTER
Selects an available picture setup
mode.
6. BLANK
Used to hide the screen picture.
7. Keystone/Arrow keys ( Up,
Down)
Manually corrects distorted images
resulting from an angled projection.
8. VOLUME (+, -)
Adjusts the sound level.
9. AUTO
Automatically determines the best
picture timings for the displayed
image.
10. Right
Activates panel key lock.
When the On-Screen Display (OSD)
menu is activated, the #3, #4, and #9
keys are used as directional arrows to
select the desired menu items and to
make adjustments.
11. SOURCE
Displays the source selection bar.
12. MAGNIFY (+, -)
Magnifies or reduces the projected
picture size.
13. TIMER ON
Activates or displays an on-screen
timer based on your own timer setting.
14. TIMER SET UP
Enters presentation timer setting
directly.
15. Battery cover
1
2
5
4
8
6
7
3
7
9
12
11
13
10
14
15
I
I

9
Remote control effective range
The Infra-Red (IR) remote control is located on the front
of the projector. The remote control must be held at an
angle within 30 degrees perpendicular to the projector's
IR remote control sensor to function correctly. The
distance between the remote control and the sensor should
not exceed 4 meters (~ 13 feet).
Make sure that there are no obstacles between the remote
control and the IR sensor on the projector that might
obstruct the infra-red beam.
Replacing the remote control battery
1. Pull out the battery holder.
Please follow the illustrated instructions. Push and hold
the locking arm while pulling out the battery holder.
2. Insert the new battery in the holder. Note the
positive polarity should face outward.
3. Push the holder into the remote control.
WA R N I NG
Improper use may result in battery explosion, cracking or
leakage, which could result in fire, injury and/or pollution
of the surrounding environment. If you observe battery
leakage, wipe out the leakage and then replace a battery.
If the leakage adheres to your body or clothes, rinse well
with water immediately.
• Keep the battery away from children and pets. Be careful for them not to swallow a battery.
• Avoid leaving the remote control and battery in an excessive heat or humid environment
like the kitchen, bathroom, sauna, sunroom or in a closed car.
• Replace only with the same or equivalent type recommended by the battery
manufacturer: [type: CR2025]
• Dispose of the used battery according to the manufacturer's instructions and local
environment regulations for your region.
• Never throw the battery into a fire. There may be danger of an explosion.
• If the battery is dead or if you will not be using the remote control for an extended period
of time, remove the battery to avoid damage to the remote control from possible battery
leakage.
• Do not recharge, short circuit, solder or disassemble a battery.
15º
15º 4m
(approx.)

10
Positioning your projector
Choosing a location
Your room layout or personal preference will dictate which installation location you select.
Take into consideration the size and position of your screen, the location of a suitable power
outlet, as well as the location and distance between the projector and the rest of your
equipment.
Your projector is designed to be installed in one of following possible installation locations:
1. Normal
Select this location with the projector placed near
the floor in front of the screen. This is the most
common way to position the projector for quick
setup and portability.
2. H Invert
Select this location with the projector placed near
the floor behind the screen.
Note that a special rear projection screen is
required.
Set H Invert in the SYSTEM SETTING:
BASIC > Mirror menu after you turn the
projector on.

11
Projection dimensions
Refer to "Dimensions" on page 50 for the center of lens dimensions of this projector before
calculating the appropriate position.
The "screen" mentioned below refers to the projection screen usually consisting of a surface
and a support structure
• There is 3% tolerance among these numbers due to optical component variations. It is
recommended that if you intend to permanently install the projector, you should
physically test the projection size and distance using the actual projector in situ before
you permanently install it, so as to make allowance for this projector's optical
characteristics. This will help you determine the exact mounting position so that it best
suits your installation location.
• To obtain the clearest image possible, we suggest that you keep the desired distance
within 1.5 to 6 m.
Desired
Distance
(m)
< A>
Minimum Screen Size (Min zoom) Maximum Screen Size (Max zoom)
Diagonal
(inch)
< B>
W (cm) x H (cm)
From base to
top of image
(cm)
< C>
Diagonal
(inch)
< B>
W (cm) x H (cm)
From base to
top of image
(cm)
< C>
1 24 49 x 37 40 26 54 x 40 44
1.5 36 74 x 55 60 40 81 x 60 67
2 48 98 x 74 80 53 108 x 81 89
2.5 60 123 x 92 101 66 134 x 101 111
3 72 147 x 110 121 79 161 x 121 132
3.5 84 172 x 129 141 93 188 x 141 156
4 96 196 x 147 161 106 215 x 161 178
4.5 108 221 x 165 181 119 242 x 181 199
5 120 245 x 184 201 132 269 x 202 221
6 144 294 x 221 241 159 323 x 242 267
7 168 343 x 257 282 185 376 x 282 310
8 192 392 x 294 322 212 430 x 323 355
9 216 441 x 331 362 238 484 x 363 399
10 241 490 x 368 404 265 538 x 403 444
11 265 539 x 404 444 291 591 x 444 488
12 289 588 x 441 484 318 645 x 484 533
Zoom Ratio: 1.1 x
A
B
B
CC
Maxscreen
size
Minscreen
size

12
Connection
When connecting a signal source to the projector, be sure to:
1. Turn all equipment off before making any connections.
2. Use the correct signal cables for each source.
3. Ensure the cables are firmly inserted.
• In the connections shown below, some cables may not be included with the projector (see
"Shipping contents" on page 5). They are commercially available from electronics stores.
• The connection illustrations below are for reference only. The rear connecting ports
available on the projector vary with each projector model.
• For detailed connection methods, see pages 13-16.
HDMI
AUDIO
OUT
RGB IN
RL
RGB OUT
RL
COMPONENT
Cb/Pb
Y
Cr/Pr
AUDIO
OUT
RLL
R
L
VIDEO
S-VIDEO
AUDIO
OUT
AUDIO
OUT
HDMI
Computer
Monitor
Speakers
(with an amplifier)
VCR/DVD/Blu-ray DiscTM player

13
Connecting a computer or monitor
Connecting a computer
The projector provides two VGA input sockets that allow you to connect them to both
IBM® compatibles and Macintosh® computers. A Mac adapter is needed if you are
connecting legacy version Macintosh computers.
To connect the projector to a notebook or desktop computer:
1. Take the supplied VGA cable and connect one end to the D-Sub output socket of the
computer.
2. Connect the other end of the VGA cable to the COMPUTER IN1 or COMPUTER
IN2 signal input socket on the projector.
Many notebooks do not turn on their external video ports when connected to a projector.
Usually a key combo like FN + F3 or CRT/LCD key turns the external display on/off. Locate a
function key labeled CRT/LCD or a function key with a monitor symbol on the notebook. Press
FN and the labeled function key simultaneously. Refer to your notebook's documentation to
find your notebook's key combination.
Connecting a monitor
If you want to view your presentation close-up on a monitor as well as on the screen, you
can connect the MONITOR OUT signal output socket on the projector to an external
monitor with a VGA cable following the instructions below:
To connect the projector to a monitor:
1. Connect the projector to a computer as described in "Connecting a computer" on page
13.
2. Take a suitable VGA cable (only one supplied) and connect one end of the cable to the
D-Sub input socket of the video monitor.
Or if your monitor is equipped with a DVI input socket, take a VGA to DVI-A cable
and connect the DVI end of the cable to the DVI input socket of the video monitor.
3. Connect the other end of the cable to the MONITOR OUT socket on the projector.
The MONITOR OUT output only works when COMPUTER IN1 connection is made to the
projector.

14
Connecting Video source devices
You can connect your projector to various Video source devices that provide any one of the
following output sockets:
• HDMI
• Component Video
•S-Video
• Video (composite)
You need only connect the projector to a Video source device using just one of the above
connecting methods, however each provides a different level of video quality. The method
you choose will most likely depend upon the availability of matching terminals on both the
projector and the Video source device as described below:
Best video quality
The best available video connection method is HDMI. If your source device is equipped
with a HDMI socket, you can enjoy uncompressed digital video quality.
See "Connecting an HDMI device" on page 15 for how to connect the projector to a HDMI
source device and other details.
If no HDMI source is available, the next best video signal is Component video (not to be
confused with composite video). Digital TV tuner and DVD players output Component
video natively, so if available on your devices, this should be your connection method of
choice in preference to (composite) video.
See "Connecting a Component Video source device" on page 15 for how to connect the
projector to a component video device.
Better video quality
The S-Video method provides a better quality analog video than standard composite Video.
If you have both composite Video and S-Video output terminals on your Video source
device, you should elect to use the S-Video option.
See "Connecting an S-Video source device" on page 16 for how to connect the projector to
an S-Video device.
Least video quality
Composite Video is an analog video and will result in a perfectly acceptable, but less than
optimal result from your projector, being the least video quality of the available methods
described here.
See "Connecting a composite Video source device" on page 16 for how to connect the
projector to a composite Video device.
Connecting audio
The projector has one built-in mono speaker which is designed to provide basic audio
functionality accompanying data presentations for business purposes only. It is not designed
for, nor intended for stereo audio reproduction use as might be expected in home theater or
home cinema applications. Any stereo audio input (if provided), is mixed into a common
mono audio output through the projector speaker.
If you wish, you can make use of the projector (mixed mono) speaker in your presentations,
and also connect separate amplified speakers to the Audio Out socket of the projector. The
audio output is a mixed mono signal and controlled by the projector Volume and Mute
settings.

15
If you have a separate sound system, you will most likely want to connect the audio output
of your Video source device to that sound system, instead of to the mono audio projector.
• The audio output only works when a signal source is connected to the projector.
• When an audio cable is connected to the AUDIO OUT port, the projector’s speaker will be
muted.
Connecting an HDMI device
You should use an HDMI cable when making connection between the projector and HDMI
devices.
To connect the projector to an HDMI device:
1. Take an HDMI cable and connect one end to the HDMI output port of the video
device.
2. Connect the other end of the cable to the HDMI input port on the projector.
The projector is only capable of playing mixed mono audio, even if a stereo audio input is
connected. See "Connecting audio" on page 14 for details.
Connecting a Component Video source device
Examine your Video source device to determine if it has a set of unused Component Video
output sockets available:
• If so, you can continue with this procedure.
• If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to a Component Video source device:
1. Take a VGA (D-Sub)-Component adaptor cable and connect the end with 3 RCA type
connectors to the Component Video output sockets of the Video source device. Match
the color of the plugs to the color of the sockets; green to green, blue to blue, and red
to red.
2. Connect the other end of the VGA (D-Sub)-Component adaptor cable (with a D-Sub
type connector) to the COMPUTER IN1 or COMPUTER IN2 socket on the
projector.
• The projector is only capable of playing mixed mono audio, even if a stereo audio input is
connected. See "Connecting audio" on page 14 for details.
• If the selected video image is not displayed after the projector is turned on and the correct
video source has been selected, check that the Video source device is turned on and
operating correctly. Also check that the signal cables have been connected correctly.

16
Connecting an S-Video source device
Examine your Video source device to determine if it has an unused S-Video output socket
available:
• If so, you can continue with this procedure.
• If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to an S-Video source device:
1. Take an S-Video cable and connect one end to the S-Video output socket of the Video
source device.
2. Connect the other end of the S-Video cable to the S-VIDEO socket on the projector.
• The projector is only capable of playing mixed mono audio, even if a stereo audio input is
connected. See "Connecting audio" on page 14 for details.
• If the selected video image is not displayed after the projector is turned on and the correct
video source has been selected, check that the Video source device is turned on and
operating correctly. Also check that the signal cables have been connected correctly.
• If you have already made a Component Video connection between the projector and this
S-Video source device using Component Video connections, you need not connect to this
device using an S-Video connection as this makes an unnecessary second connection of
poorer picture quality. See "Connecting Video source devices" on page 14 for details.
Connecting a composite Video source device
Examine your Video source device to determine if it has a set of unused composite Video
output sockets available:
• If so, you can continue with this procedure.
• If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to a composite Video source device:
1. Take a Video cable and connect one end to the composite Video output socket of the
Video source device.
2. Connect the other end of the Video cable to the VIDEO socket on the projector.
• The projector is only capable of playing mixed mono audio, even if a stereo audio input is
connected. See "Connecting audio" on page 14 for details.
• If the selected video image is not displayed after the projector is turned on and the correct
video source has been selected, check that the Video source device is turned on and
operating correctly. Also check that the signal cables have been connected correctly.
• You need only connect to this device using a composite Video connection if Component
Video and S-Video inputs are unavailable for use. See "Connecting Video source devices"
on page 14 for details.

17
Operation
Starting up the projector
1. Plug the power cord into the projector and into a
wall socket. Turn on the wall socket switch
(where fitted).
2. Press on the projector or remote control to
start the projector. The POWER indicator light
stays blue when the projector is on.
(If necessary) Rotate the focus ring to adjust the
image clearness.
• If the projector is still hot from previous activity, it
will run the cooling fan for approximately 60
seconds before energizing the lamp.
• To maintain the lamp life, once you turn the
projector on, wait at least 5 minutes before turning it
off.
• Also, do not turn the projector on for about 10
minutes or more after turning off.
3. If the projector is activated for the first time,
select your OSD language and High Altitude
Mode following the on-screen instructions.
Language
See "Using the menus" on page 18 for details.
High Altitude Mode
See "Operating in a high altitude environment" on page 31 for details.
4. Switch all of the connected equipment on.
5. The projector will start to search for input signals. The current input signal being
scanned appears in the upper left corner of the screen. If the projector doesn't detect a
valid signal, the message 'No Signal' will continue to be displayed until an input
signal is found.
You can also press SOURCE on the projector or remote control to select your desired
input signal. See "Switching input signal" on page 21 for details.
• If the frequency/resolution of the input signal exceeds the projector's operating range, you
will see the message 'Out of Range' displayed on a blank screen. Please change to an
input signal which is compatible with the projector's resolution or set the input signal to a
lower setting. See "Timing chart" on page 51 for details.
• OSD languages and user manual languages may not match.
I
I

18
Using the menus
The projector is equipped with On-Screen Display (OSD) menus for making various
adjustments and settings.
The OSD screenshots below are for reference only, and may differ from the actual design.
Below is the overview of the OSD menu.
To use the OSD menus, please set them to your familiar language first.
1. Press MENU on the projector or
MENU/EXIT on the remote control
to turn the OSD menu on.
3. Press to highlight Language
and press MODE/ENTER.
2. Use / to highlight the SYSTEM
SETTING: Basic menu.
4. Press / / / to select a
preferred language.
5. Press MENU on the projector or
MENU/EXIT on the remote
contrl to leave and save the
settings.
: DISPLAY
: PICTURE
: SOURCE
: SYSTEM SETTING: Basic
: SYSTEM SETTING: Advanced
: INFORMATION
Current input
signal
Main menu icon
Sub-menu
Highlight
Go to the
previous page
or to exit.
Status
Wall Color
3D Sync Invert
3D Sync
Digital Zoom
H. Size
Phase
Position
Keystone
Aspect Ratio
Analog RGB
Off
Auto
Disable
15
15
MENU Exit
Wall Color
3D Sync Invert
3D Sync
Digital Zoom
H. Size
Phase
Position
Keystone
Aspect Ratio
Analog RGB
Off
Auto
Disable
15
15
MENU Exit
Presentation Timer
Background Color
Sleep Timer
Panel Key Lock
Blank Timer
Auto Power Off
Mirror
Language
Analog RGB
Original
Disable
Normal
30 min
Disable
Off
MENU Exit
ENTER
Presentation Timer
Background Color
Sleep Timer
Panel Key Lock
Blank Timer
Auto Power Off
Mirror
Language
Analog RGB
English
Original
Disable
Normal
30 min
Disable
Off
MENU Exit

19
Utilizing the password function
For security purposes and to help prevent unauthorized use, the projector includes an option
for setting up password security. The password can be set through the On-Screen Display
(OSD) menu. For details of the OSD menu operation, please refer to "Using the menus" on
page 18.
You will be inconvenienced if you activate the password functionality and subsequently forget
the password. Print this user manual (if necessary) and write the password you used in this
manual, and keep it in a safe place for later use.
Setting a password
1. Open the OSD menu and go to the SYSTEM SETTING: Advanced > Security
Settings menu. Press MODE/ENTER on the projector or remote control. The
Security Settings page is displayed.
2. Highlight Change Password and press MODE/ENTER.
3. As pictured to the right, the four arrow keys
( , , , ) respectively represent 4 digits (1,
2, 3, 4). According to the password you desire to
set, press the arrow keys to enter six digits for the
password.
4. Confirm the new password by re-entering the
new password.
Once the password is set, the OSD menu returns to the Security Settings page.
5. To activate the Power on Lock function, press / to highlight Power on Lock and
press / to select On. When the Power on Lock function is activated, you have to
enter the correct password to turn on the projector.
6. To leave the OSD menu, press MENU on the projector or MENU/EXIT on the
remote control.
• Once a password has been set, the projector cannot be used unless the correct password
is entered every time the projector is started.
• The digits being input will be displayed as asterisks on-screen. Write your selected
password down here in this user manual in advance or right after the password is entered
so that it is available to you should you ever forget it.
Password: __ __ __ __ __ __
Keep this user manual in a safe place.
If you forget the password
If the password function is activated, you will be asked
to enter the six-digit password every time you turn on
the projector. If you enter the wrong password, the
password error message as pictured to the right is
displayed lasting for three seconds, and the message
'INPUT PASSWORD' follows. You can retry by
entering another six-digit password, or if you did not
record the password in this user manual, and you absolutely do not remember it, you can use
the password recall procedure. See "Entering the password recall procedure" on page 20 for
details.
If you enter an incorrect password 5 times in succession, the projector will automatically
shut down in a short time.
INPUT NEW PASSWORD
BackMENU
*
Password Error
Please try again.