Dukane Starfire HD 4010 User manual

MODELS
SF6000
SF5510
SF4030
SF4010
SF3010
SF3000
HD 4010

This Dukane audio visual product is warranted to the original
purchaser under a 5year limited warranty – – in normal use and
service – – against defects in material and workmanship. DUKANE
CORPORATION EXPRESSLY DISCLAIMS ALL OTHER WARRANTIES,
EXPRESSED OR IMPLIED,INCLUDING ALL WARRANTIES OF MERCHANT-
ABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
During the warranty period, Dukane Corporation will repair or
replace (at the Manufacturer’s option) any such defective parts
(except for lamps, which are subject to whatever warranties the
manufacturer may provide) without charge to the purchaser for
parts or labor when the product is returned, prepaid and insured, with
proof of purchase date. This remedy of repair or replacement is
exclusive of all other remedies that the purchaser may have.
This exclusive remedy is void if the product has been damaged by
accident or unreasonable use, neglect, or improper service or other
causes not arising out of defects in material or workmanship.
Dukane Corporation disclaims all liability for incidental or con-
sequential damages of any kind, including all damages arising out
of any interruptions in operation of the product and all damages
to software.
No person, firm or representative is authorized to assume any
obligation or make any warranty on behalf of the Dukane Corporation
other than as stated above.
THIS LIMITED WARRANTY IS VALID FOR U.S.A. AND CANADA.
FOR OTHER LOCATIONS, LOCAL WARRANTIES APPLY.
5 YEAR LIMITED WARRANTY
2900 Dukane Drive • St. Charles, IL 60174-3395
Phone: [phone] • Fax: [phone]
E-mail: [email protected] • Internet: www.dukcorp.com/av
Audio Visual Products
401-546-06
5
Audio Visual Products

When using your overhead projector, basic safety precautions should
always be followed, including the following:
1. Read and understand all instructions before using.
2. Close supervision is necessary when any projector is used by or near
children. Do not leave projector unattended while in use.
3. Care must be taken as burns can occur from touching hot parts.
4. Do not operate projector with a damaged cord or if the projector
has been dropped or damaged — until it has been examined by a
qualified service technician.
5. Position the cord so that it will not be tripped over, be pulled or
contact hot surfaces.
6. If an extension cord is necessary, a cord with a current rating at least
equal to that of the projector should be used. Cords rated for less
amperage than the projector may overheat.
7. Always unplug projector from electrical outlet before cleaning and
servicing and when not in use. Never yank cord to pull plug from
outlet. Grasp plug and pull to disconnect.
8. Let projector cool completely before putting away.
9. To protect against the risk of electric shock, do not immerse this
projector in water or other liquids.
10. To avoid the risk of electric shock, do not disassemble this projector,
but take it to a qualified service technician when some service or
repair work is required. Incorrect reassembly can cause electric
shock when the projector is used subsequently.
11.
The use of an accessory attachment not recommended by the manufac -
turer may cause a risk of fire, electric shock or injury to persons.
12. Connect this projector to a grounded outlet.
13. Disconnect this unit from its source of supply before replacing the
projection lamp.
Additional lamp safeguards: never handle lamps with bare fingers; periodi-
cally inspect lamps, when they’re turned off, for signs of blistering or
blackening; insure proper action of the cooling system; turn off the
projector immediately if the image becomes abnormally dim; never
operate a projector with the lamp housing open; and make sure that the
lamp itself is properly seated.
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS

The sleek, low-profile Starfire Overhead Projectors are
available in your choice of 3000, 4000/3200, 5500/4400
and 6000 ANSI lumens. Features of each model vary and can
include a single, triple or triple/wide-angle lens; built-in
AC outlets; and even an electronic “soft start” power supply
that improves the projected image, extends the
lamp life and reduces operating costs.
Because operation of all units is very similar, this
manual covers all models in the Dukane Starfire Series.
2900 Dukane Drive • St. Charles, IL 60174-3395
Phone: [phone] • Fax: [phone]
E-mail: [email protected] • Internet: www.dukane.com
Audio Visual Products
Thank you for choosing a
Starfire® Series
Portable/Professional
Overhead Projector.

LIFETIME LIMITED WARRANTY .................................Inside Cover
SPECIFICATIONS .................................................................. 1
ELECTRICAL SAFETY GROUNDING INSTRUCTIONS ........................ 1
INDEX OF FUNCTIONAL PARTS ............................................. 2-3
SF MODEL SETUP and FOLDUP ............................................. 4-5
HD MODEL SETUP ................................................................. 6
OPERATION ......................................................................... 7
Image Adjustment .......................................................... 7
High/Low Lamp Switch....................................................8
Lamp Changer ................................................................ 8
LAMP REPLACEMENT ............................................................. 9
CLEANING ......................................................................... 10
SERVICING ........................................................................ 10
Shipping Information .................................................... 10
Service........................................................................ 10
No Charge Warranty Repair............................................. 10
TROUBLESHOOTING ............................................................ 11
INFORMATION ON LAMP WARRANTY ...................................... 11
SF MODEL OPTIONAL ACCESSORIES ........................................ 12
HD MODEL OPTIONAL ACCESSORIES ....................................... 13
TABLE OF CONTENTS Page

SPECIFICATIONS
SF MODEL Dimensions........... 5.6" H x 16.4" W x 17.8" D (Folded)
32" H x 16.4" W x 17.8" D (Opened)
HD MODEL Dimensions.......... 8.5" H x 16.4" W x 17.8" D (Folded)
32" H x 16.4" W x 17.8" D (Opened)
Aperture............................... 6000, 5510 — 11.2" x 11.2" (A4)
3000, 3010, 4010, 4030 — 10.5" x 10.5"
Lens ............................ 3000 — Single Element, 293mm (11.5")
3010, 4010, 5510 — Three Element, 327mm (13.0")
4030, 6000 — Four Element, 280mm (11.0")
Lamp ............................................... 3000, 3010 — 360W, ENX
4010, 4030, 5510, 6000 — 410W, FXL
Elevation...................................................... Up to 20 Degrees
Focus............................................................ Rack and Pinion
Power .....................................3000, 3010 — 120V, 60Hz, 4.4A
4010, 5510 — 120V, 60Hz, 9.8A
4030, 6000 — 120V, 60Hz, 10.3A
SF MODEL Power Cord ............................3-Wire Grounded, 10 Ft.
HD MODEL Power Cord ...........................3-Wire Grounded, 10 Ft.
Safety ............ Safety Interlock System, Automatic Thermal Cutoff
SF MODEL Weight.........................................................19 Lbs.
HD MODEL Weight.........................................................22Lbs.
1
ELECTRICAL SAFETY
GROUNDING INSTRUCTIONS
This Class I product uses a three-wire power cord that grounds
the product for your protection. Do not DEFEAT or REMOVE the
grounding pin. If an extension cord is used, it must also be a
three-wire type with an ampere rating equal to or greater than
the product’s rating. The plug must be connected to a properly
grounded three-terminal power receptacle. Connection to any
other type of receptacle should be done only by a qualified
electrician in accordance with local and/or national electrical
codes.

3
2a
9 11
1
6
5
4
7
8
10
2
A number of terms are used frequently in this instruction booklet.
The OVERHEAD PROJECTOR will be easier to operate if you become
familiar with the terms for the functional parts listed below:
INDEX OF FUNCTIONAL PARTS
1. Mirror; use to direct projected
image
2. Projection Head; rotates 180°
to allow projection in different
directions or onto different
screens
2a. Rotate in 4th element mag-
nification lens (Models 6000
and 4030) for enlarged image
from same distance
3. 120V AC Outlet; for use with
LCD panel/computer connection
(4010, 4030, 5510, 6000 models
only — 5A MAX!)
4. Mast; rack & pinion focusing
mechanism
5. Focus Knob; turn to focus pro-
jected image
6. Stage; place presentation media
here for projection
7. Stage Latch; release for lamp
access
8. Base Housing
9. Locking Collar; push down to
release mast (foldaway design)
10. Power Switch
11. High/Low Switch; (4010, 4030,
5510, 6000 models only)
2

3
12 15
13
14
12. Door Leg Assembly; close for
foldaway design, cord storage
13. Door Latch (one each side);
keeps doors closed
14. Lamp Change Lever; slide for
replacement/reserve lamp
15. Power Cord; stored in the unit’s
base
Models 6000 and 4030 also feature a soft start power supply which
extends lamp life, reduces operating costs and ensures a smoother,
flicker-free image.

1. Set unit on projection table in the vertical position (handle up).
2. Slide bottom door latches out and swing both doors around to
magnet latches. Pull out the entire power cord. Leave doors open.
3. Tip unit over to rest on its legs. (Doors act as feet for the unit).
4. Turn focus knob clockwise until it stops at the end of the mast.
5. Rotate mast up until it locks into place.
6. Rotate the projection head assembly counterclockwise to the
working position.
7. Open mirror.
SETUP INSTRUCTIONS SF MODELS
4
S TEP 1 —
S TEP 3 —
S TEP 2 —
S TEP 4 —
S TEP 5 —
Slide
latches out
and swing
doors open.
Remove entire cord.
Doors must be
open for unit
to operate.

FOLDUP INSTRUCTIONS
5
Perform Setup Steps in reverse order.
• Unlock/lower mast by pushing down on lock collar as shown.
S TEP 7 —S TEP 6 —

1. Set unit on projection table and pull out the power cord from cord
storage compartment.
2. Turn focus knob clockwise until it stops at the end of the mast.
3. Rotate mast up until it locks into place.
4. Rotate the projection head assembly counterclockwise to the
working position.
5. Open mirror.
SETUP INSTRUCTIONS HD MODELS
6
S TEP 1 —
S TEP 2 —
S TEP 5 —
S TEP 3 —
S TEP 4 —

Place the projector on a stable surface that is desk or table height.
Make sure that the side vent is not blocked. Plug the power cord
into a standard 120V AC outlet. Push the power button to turn the
projector on. I=ON
O = OFF
Place a transparency on the stage. Adjust the focus by turning the
focus knob. You may alternate between the wide angle (SF6000 &
4030) and standard lens by rotating the 4th element lens towards
or away from the projection head (some adjustment on screen-to-
projector distance may be necessary).
Image Adjustment
A. Position the projected image on screen (height location) by
adjusting mirror angle.
B. Correct the image tilt or change projection direction by rotating
the lens/mirror assembly as required.
OPERATION
7
S TEP A —
S TEP B —

CAUTION
Do not overload 120V AC outlets with accessories that
exceed a total of 5 amps.
8
CAUTION: If the OHP is brought directly from a cold to a warm
location or it is placed in a very humid room, moisture may condense
on electrical and optical parts in the unit. If this occurs, wait for
OHP to reach room temperature before turning it “ON.”
High/Low Lamp Switch
When using with an LCD panel, use the projector at its brightest
lumen output (Models 6000, 5510, 4030, 4010).
Reduce light output (High/Low switch) to extend lamp life. Ideal
when using regular transparencies.
Lamp Changer
The lamp changer allows you to quickly replace a failed lamp. Turn
the power switch “OFF.” Simply push slightly, then slide the lamp
changing lever towards the side labeled “RESERVE.”
LEVER

Your projector uses:
3000, 3010 — 360W, ENX.
4010, 4030, 5510, 6000 — 410W, FXL.
LAMP REPLACEMENT
WARNING
Lamp and adjacent metal parts are hot. Allow lamp to cool
before replacing. Glass components may shatter.
Handle carefully.
To Remove an Exhausted Lamp:
1. Remove the lamp by squeezing the lamp retainer clip and
remove lamp.
2. Avoid touching the new lamp — oily skin can cause discoloration
of the lamp capsule or reflector.
3. Push the new lamp down into socket until firmly seated and
the reflector lines up with the aperture. Re-engage the lamp
retainer clip.
9

10
CLEANING
For best performance, keep your projector free of dust and surface
dirt. Keep covered when not in use.
Daily Cleaning: Use a soft, lint-free cloth to remove dust from
stage glass, projection lens and magnifier lens (6000 and 4030
models only). Lens cleaner may also be used on these components.
Projection Mirror: Do not attempt to clean this mirror with
cleaning agents — use a soft lens brush to remove dirt.
Fresnel Lens: Use a soft, lint-free cloth or soft brush to remove
dust. Use of cleaning agents may damage optics. Disassembly
is not recommended.
Shipping Information
If it becomes necessary to return a unit, please use the original
packing material or pack securely to insure safe shipment.
Service
Service and parts are available from Dukane or from an approved
service station. Contact the Dukane Service Department at
1-800-676-2487 to order parts or for the nearest service station.
Service manuals are also available at a nominal cost.
No Charge Warranty Repair
Your unit must be taken or sent to Dukane or to an approved service
station with your sales receipt.
SERVICING

11
TROUBLESHOOTING
Symptom Probable Cause Solution
Neither lamp or a. Unit unplugged a. Plug unit into
fan operate outlet
b. No power at wall outlet b. Verify outlet
has power
c. Stage lid not closed c. Close stage lid
d. Mirror box not lowered, d. Open bottom
(interlock switch not doors and insure
activated) mirror box lowers
e. Blown fuse e. Call service
No lamp, fan runs a. Burned-out lamp a. Replace lamp
b. Lamp changer not engaged b. Slide changer arm
into position
c. Lamp not seated in receptacle c. Seat lamp
New lamp installed, a. Defective lamp a. Try another new
lamp still not on, lamp
fan runs b. Defective electrical system b. Call service
No fan, lamp on a. Fan is obstructed a. Call service
b. Fan motor has burned out b. Call service
INFORMATION ON LAMP WARRANTY
Projection lamps are warranted by the lamp manufacturer and not
by the equipment manufacturer. If you have a lamp which you
believe to be defective, contact the manufacturer of that particular
lamp for the appropriate warranty replacement.
A BULB, Inc. WIKO Ltd.
134 Golden Gate Ave., Suite B 10490 W. 164th Place
San Francisco, CA 94102 Orland Park, IL 60462-5495
1-888-882-2852 1-800-524-1754
Osram-Sylvania Products, Inc. General Electric Company
100 Endicott St. 1501 South 19th Street
Danvers, MA 01923 Mattoon, IL 61938
1-888-677-2627 1-800-435-2677
Call Service at 1-800-676-2487.

12
OPTIONAL ACCESSORIES SF MODELS
FXL LAMP
410W/82V
456-192
(Models 4010, 4030, 5500, 6000)
SOFT SHOULDER BAG
(PADDED)
128-46
ROLL FILM
ADAPTER KIT
438-814
HARD-SIDED
CARRYING CASE
185-398 ATA SHIPPING CASE 185-397 ACETATE ROLL (50') 310-6
PROTECTIVE
DUST COVER
128-61
ENX LAMP
360W/82V
456-188
(Models 3000/3010)
To order
accessories,
please call
1-800-676-2487.

13
OPTIONAL ACCESSORIES HD MODELS
FXL LAMP
410W/82V
456-192
(Models 4010, 4030, 5500, 6000)
SOFT SHOULDER BAG
(PADDED)
128-1
ROLL FILM
ADAPTER KIT
438-814
HARD-SIDED
CARRYING CASE
185-385 ATA SHIPPING CASE 185-397
ENX LAMP
360W/82V
456-188
(Models 3000/3010)
To order
accessories,
please call
1-800-676-2487.

Part # 401-545-05