Duke FLM 100 User manual

This manual is Copyright © 2019 Duke Manufacturing Co. All rights reserved.
Reproduction without written permission is prohibited. Duke is a registered
trademark of the Duke Manufacturing Co.
CAUTION: Please read these instructions completely before attempting
to install, operate or service this equipment.
WARNING: Cancer and Reproductive Harm -
www.p65warnings.ca.gov
Instruction Sheet
FLM 100 Retro Fit Half Rack Split
P/N 2503963
REV C 08/26/2019
Full Bread & Full Bread w/Cheese Recipes:
Stage 1:Change “stage time” to 18 minutes, “humidity time” to
18 minutes, and“H20 on Time” to 1.
Stage 2: Change “stage time” to 6 minutes
Stage 3: Change “H2O on Time” to 1
*all other values will remain as is
Half Bread & Half Bread w/Cheese Recipes:
Stage 1:Change “stage time” to 18 minutes, “humidity time”to
18 minutes, and“H20 on Time” to 1.
Stage 2: Change “stage time” to 6 minutes
Stage 3: Change “H2O on Time” to 1
*all other values will remain as is
Should you have any questions during the installation of your
upgrade kit or with programming the updated Flexbake5 All in
One oven recipes, please call our technical service team at: 1-800-
735-3853 ext. 1.
Regards,
Your Team and Duke Manufacturing
1-800-735-3853 www.dukemfg.com/Subway
In this package, you are receiving an upgrade kit for your front line bread display cabinet intended to
enhance the hold time of bread in the cabinet. Included are instructions to install the upgrade kit.
When holding bread in the display cabinet, holding full batches and rotating product will yield the
best results.
Lastly, if your restaurant utilizes a Flexbake5 All in One oven, there is an updated recipe that will need
to be loaded into your oven. The recipe changes are as follows:

2
Installation and Operation of: FLM100 Half Rack Retro
INSTALLATION
Please read these instructions completely before attempting
to install, operate or service this equipment.
Step 2
Locate the two removable tabs
holding the wire racks in place
and remove them using a Phillips
Head Screwdriver.
Step 3
Insert the partition plate provided
between the lower sheet metal
rack and the upper wire rack. The
wire racks may need to be pulled
up slightly to make room for this
plate.
Step 1
Make sure unit is disconnected
from any power source. Remove
top ve baskets from unit.
Remove
1
2
3
4
5
Step 4
Slide the rack all the way in until
the back anges is resting against
the inside of the cabinet wall.
Step 5
Make sure that the wire rack is
resting between the cabinet wall
and the partition plate ange.
Step 6
Install the edge trim-seal to the
ange of the partition plate. Make
sure it is pushed all the way onto
the ange and is secure.
NOTE: There should
be approximately
1” overlapping the
partition plate on
each side.
NOTE: Adjust side-
to-side accordingly
to make sure this
overlap does not
interfere with the
door gasket.
Tools Required:
Phillips Head Screwdriver
Dry Erase Pen
Parts Included:
• Partition Plate,
• Edge Trim Gasket,
• Aluminum Strip with Adhesive
• Alcohol Pads

3
Installation and Operation of: FLM100 Half Rack Retro
INSTALLATION - continued
Step 7
With the door closed, place
the non-adhesive side of the
aluminum strip against the glass
and position it so it completely
covers the previously installed
gasket.
NOTE: Too high
or too low will
negatively aect
the performance
and sealing.
Too High
Too Low
Correct
Draw Line Above
Step 7A
Using a dry erase marker, draw a
line all the way across the glass
on both the top and bottom of
the aluminum strip using it as a
straight edge.
Draw Line Below
Step 8
Open the door. Take the
Aluminum strip with the double
sided tape and peel o the
backing strip from the tape.
Step 10
Place one end of the aluminum
strip against the glass, making
sure that it is within the two lines
drawn from step 7. Once one side
is attached to the glass, line up
the rest of the aluminum strip
with the drawn lines and rmly
press down to make sure it is
properly adhered. The aluminum
strip should be centered in
between both lines from step 7.
NOTE: be careful
not to touch the
adhesive as the oil
from your ngers
will cause it not to
adhere properly.
Step 9
Open the door. On the
inside clean glass with
alcohol wipes.
Step 11
Close the door and verify that the
aluminum strip makes contact
with the gasket.
Step 12
Clean the marks o of the outside
of the glass.
Step 14
Unplug all of the lights in the
bread cabinet from the power
supply located on the adjacent
unit. This is done to help extend
the holding time and improve the
quality of the bread.
Step 13
Reinstall bread baskets removed
in step 1.

Installation and Operation of: FLM100 Half Rack Retro
Duke Manufacturing Co.
2305 N. Broadway
St. Louis, MO 63102
Phone: [phone]
Toll Free: 1-800-735-3853
Fax: [phone] www.dukemfg.com
INSTALLATION - continued
UPDATE - COMPLETE
Step 15
Level Unit. To ensure the door of this unit seals
completely, the unit must be fully leveled in all
directions.
NOTE: This must be done
before the unit is sealed to
the oor or built into a curb.
NOTE: The unit can be
leveled by adjusting the feet
using adjustable pliers.
Step 15A
Level Unit front to back on both sides.
Step 15B
Level unit side to side, both front and back.
Step 15C
Check the top and bottom corner seal of the door
gasket. There should be no gap.
NO GAP GAP
RE-ADJUST