Dundalk LeisureCraft Pure Cube PU550 User manual

Pure Cube Indoor Sauna Assembly Instructions
Tools Required
Carpenters Hammer
Cordless Drill
7/16” Drill Bit
11/16” Drill Bit
Hex Keys (Included)
Tape Measure
Step Ladder
Rubber Mallet
Level
Rev.3

ph: 519-923-9813 | [email protected]| web: www.dundalkleisurecraft.com
Indoor Pure Cube Sauna
Assembly Instructions
Before you begin the installation of your Pure Cube Sauna, Please read these instructions completely.
Make sure the placement for your sauna is level and on a solid base.
Fig 2a
Fig 2b
*Always ensure that you have the correct screw length so that there will be enough thread to hold, and
especially, so that the screw does not go all the way through the material and come out the other side.
Parts Identification
The pure cube indoor sauna is available in 2 sizes,
•PU550 - 5’ x 5’ (1.54m x 1.54m)
•PU570 - 5’ x 7’ (1.54m x 2.1m)
The Pure Cube Sauna consists of 2 different sizes of wall panels that are available in either;
solid cedar (privacy)
•Glass
•wood/glass (semi-privacy)
Privacy panels
(shown in large and small panels)
Glass panel
(shown in large panel)
Semi-privacy panel
(shown in large panel)
Roof Panel
PU550 model – 2 Roof Panels
PU570 – 2 Roof Panels
Corner Posts
Corner & Wall Trim
(wall trim quantity will depend on model of sauna)
1

ph: 519-923-9813 | [email protected]| web: www.dundalkleisurecraft.com
Indoor Pure Cube Sauna
Assembly Instructions
Fig 2a
Fig 2b
Parts Identification (Cont..)
Bench Seats
Saaku Electric Heater Flat Floor
2 ½” (63mm)
Finishing Nails
Hardware
2 ½” (63mm)
Wood Screws
2 ¾” (70mm)
Connector Bolts
2 ¾” (70mm)
Connector Lag Bolts
Threaded Cap Nuts
Bench Front Enclosures
Bench Brackets
Backrest
2
Top Bench
Bottom Bench

ph: 519-923-9813 | [email protected]| web: www.dundalkleisurecraft.com
Fig 2a
Fig 2b
Make sure the panel and post are flush and secure the
panel to the post using the 2 ¾” (70mm) lag screws in
the pre drilled holes.
* Note that the solid privacy panels are labeled “TOP”.
To start the assembly of your indoor Pure Cube sauna,
place a wide wall panel and a corner post together
ensuring they are flush.
* Depending on your sauna layout, this may be a large
or a small panel.
Continue to secure the panel to the post in the
remaining pre drilled holes in the same manner
ensuring the panel and post are flush to each other.
Indoor Pure Cube Sauna
Assembly Instructions
3
Fasten a narrow wall panel to the post in the same
manner ensuring the panel and post are flush.

ph: 519-923-9813 | [email protected]| web: www.dundalkleisurecraft.com
Fig 2a
Fig 2b
Tighten with an allen key or drill.
Secure a narrow wall panel to the wide panel using the
provided lag bolts and nuts.
Secure a narrow wall panel to the other narrow panel
in the same manner as above.
Indoor Pure Cube Sauna
Assembly Instructions
4
Secure the third narrow wall panel to the other 2
narrow panels again in the same manner as the
previous steps
.

ph: 519-923-9813 | [email protected]| web: www.dundalkleisurecraft.com
Fig 2a
Fig 2b
Ensure the panel and post are flush and secure the
panel to the post using the 2 ¾” (70mm) lag screws in
the pre drilled holes to complete the back wall.
Place a corner post on to the narrow panel.
Fasten a wide wall panel to the post in the same
manner as the previous steps ensuring the panel and
the post are flush.
Indoor Pure Cube Sauna
Assembly Instructions
5
Continue on the side wall by attaching a narrow panel
to the wide panel using the lag bolts and nuts as in
previous steps.
.

ph: 519-923-9813 | [email protected]| web: www.dundalkleisurecraft.com
Fig 2a
Fig 2b
Start the front wall by securing the glass panel to the
post using the 2 ¾” (70mm) lag screws in the pre drilled
holes.
Ensure the panel and post are flush.
Ensure the panel and corner post are flush and secure
the panel to the post using the 2 ¾” (70mm) lag screws
in the pre drilled holes to complete the side wall.
Grab your door and secure it to the glass panel using
the 2 ¾” (70mm) lag screws in the pre drilled holes in
the same manner as previous steps.
Indoor Pure Cube Sauna
Assembly Instructions
6
Place the last glass panel in-between the door and the
post and secure to both in the same manner as the
previous step.

ph: 519-923-9813 | [email protected]| web: www.dundalkleisurecraft.com
Fig 2a
Fig 2b
With a helper, place one of the roof panels on top of
the sauna as shown.
Attach the last corner post to the glass panel and to the
wall panel ensuring they are flush using the 2 ¾”
(70mm) lag screws in the pre drilled holes to complete
in the same manner as previous steps.
Place the second roof panel on top of the sauna.
Before fastening, ensure the roof panels are flush to
the walls.
Indoor Pure Cube Sauna
Assembly Instructions
7
From the inside of the sauna, secure the roof panels
together using the lag bolts and nuts through the
pre-drilled holes.

ph: 519-923-9813 | [email protected]| web: www.dundalkleisurecraft.com
Fig 2a
Fig 2b
Double check to ensure the roof and walls are flush.
Tap with a rubber mallet if needed.
Tighten with a drill and allen key.
Secure the roof by screwing 2 ½” (64mm) screws up
through the wall panels into the roof.
Use 2 screws per panel and do not place screws too
close to the edge as it may cause splitting.
Indoor Pure Cube Sauna
Assembly Instructions
8
Continue around the sauna securing all the wall panels
to the roof.

ph: 519-923-9813 | [email protected]| web: www.dundalkleisurecraft.com
Fig 2a
Fig 2b
From the inside of the sauna, secure the trim piece
through the pre drilled holes using the 2 ¾” (70mm)
Connector Lag Bolts .
Line up the side trim piece with the edge of the wall
panel ensuring it is flush to the front post.
Line up the roof trim on the opposite side and secure in
the same manner as the previous step.
Indoor Pure Cube Sauna
Assembly Instructions
9
Line up the front and back pieces of roof trim in the
same manner and secure from the inside of the sauna
using the 2 ¾” (70mm) Connector Lag Bolts .

ph: 519-923-9813 | [email protected]| web: www.dundalkleisurecraft.com
Fig 2a
Fig 2b
Line up the handles with the longer handle on the
outside and thread the lag connector bolts from the
inside to the outer handle.
(Hand tighten only at this point)
To install the door handles, locate the 2 handles and 2
of the 2 ¾” (70mm) Connector Bolts .
Once you ensure the magnetic catch on the handle and
the door frame line up correctly, you can tigthen
completely.
Indoor Pure Cube Sauna
Assembly Instructions
10
Install the trim pieces over each seam.
You can use a staple gun or 1 ½” (38mm) screws.
(If using screws, you may want to pre drill your holes to
prevent the trim pieces from splitting)

ph: 519-923-9813 | [email protected]| web: www.dundalkleisurecraft.com
Fig 2a
Fig 2b
To start the installation of the benches, bring in the
bench supports and roughly place them spaced out
evenly against the back wall.
Continue adding the trim pieces all the way around the
sauna in the same process as the previous step.
Place the top bench on top of the bench supports.
Indoor Pure Cube Sauna
Assembly Instructions
11
Secure the outer bench supports to the back wall using
2 ½” (64mm) screws .

ph: 519-923-9813 | [email protected]| web: www.dundalkleisurecraft.com
Fig 2a
Fig 2b
Secure the outer bench supports to the top bench from
underneath using 2 ½” (64mm) screws .
Follow the same process to secure the bench supports
to the side walls.
To install the backrest, slide the backrest supports
behind the top bench.
Indoor Pure Cube Sauna
Assembly Instructions
12
Line the center brackets up to the supports on the
bottom of the bench.

ph: 519-923-9813 | [email protected]| web: www.dundalkleisurecraft.com
Fig 2a
Fig 2b
Secure the bench from underneath using 2 ½” (64mm) screws.
Indoor Pure Cube Sauna
Assembly Instructions
Line the brackets up to the supports on the bottom of the bench.
13
Ensure they align flush behind the bench supports and secure with 2
½” (64mm) screws.

Line the center brackets up to the supports on the
bottom of the bench.
ph: 519-923-9813 | [email protected]| web: www.dundalkleisurecraft.com
Fig 2a
Fig 2b
Secure the outer bench supports to the top bench from
underneath using 2 ½” (64mm) screws .
Follow the same process to secure the bench supports
to the side walls.
To install the backrest, slide the backrest supports
behind the top bench.
Indoor Pure Cube Sauna
Assembly Instructions
14

Place your bottom bench onto the bench supports.
Secure from underneath in the same manner as the top
bench.
ph: 519-923-9813 | [email protected]| web: www.dundalkleisurecraft.com
Fig 2a
Fig 2b
Secure the outer bench supports to the top bench from
underneath using 2 ½” (64mm) screws .
Ensure the backrests are located flush behind the
center supports and secure with 2 ½” (64mm) screws.
Ensure the bench supports are square and screw to the
floor as well.
Insert your top bench enclosure in the top opening.
Indoor Pure Cube Sauna
Assembly Instructions
15

Place your backrest to the top of the backrest supports
and secure using 2 ½” (64mm) screws ensuring that the
backrest is level.
ph: 519-923-9813 | [email protected]| web: www.dundalkleisurecraft.com
Fig 2a
Fig 2b
Repeat the process for the bottom enclosure.
Screw the enclosure to the bench supports using 2 ½”
(64mm) screws ensuring that you screw in between the
slats of the enclosure.
Again, screw in between the slats of the backrest to try
to make the screws less visible.
Indoor Pure Cube Sauna
Assembly Instructions
16

Install the supplied support screws into your marks as
shown. Screw them in until they are about ¼” (6mm)
out of the wall.
ph: 519-923-9813 | [email protected]| web: www.dundalkleisurecraft.com
Fig 2b
To install the electric heater, measure out where the
supports will go. These are usually 14 ¾” (37cm) high
and 14 ¾” (37cm) centered between the bench and the
front wall.
Bring in your flat floor and gently lay it in place in front
of the bench.
Hang the electric heater on the screws.
Screw 2 more screws in the bottom holes of the heater,
ensure the heater is level and tighten up all 4 screws.
Indoor Pure Cube Sauna
Assembly Instructions
17

Install the supplied support screws into your marks as
shown. Screw them in until they are about ¼” (6mm)
out of the wall.
ph: 519-923-9813 | [email protected]| web: www.dundalkleisurecraft.com
Fig 2b
To install the electric heater, measure out where the
supports will go. These are usually 14 ¾” (37cm) high
and 14 ¾” (37cm) centered between the bench and the
front wall.
Bring in your flat floor and gently lay it in place in front
of the bench.
Hang the electric heater on the screws.
Screw 2 more screws in the bottom holes of the heater,
ensure the heater is level and tighten up all 4 screws.
Indoor Pure Cube Sauna
Assembly Instructions
18

ph: 519-923-9813 | [email protected]| web: www.dundalkleisurecraft.com
Fig 2a
Fig 2b
Indoor Pure Cube Sauna
Assembly Instructions
Locate the pieces for your heater guard.
They consist of the following:
(A) 2 - Assembled side pieces
(B) 2 - heater guard support
4 – 2 ½” (64mm) screws
8 – 1 ½” (38mm) screws
AA
B
B
Stand the 2 Assembled side pieces (A) of the heater
guard on edge with pre-drilled holes on the bottom.
Screw heater guard support (B) to either side using
(2) – 1 ½” (38mm) screws per side.
Assemble remaining heater guard support (B) to the 2
ends in the same manner as previous step.
Place assembled heater guard around electric heater
and screw to wall using (4) 2 ½” (64mm) screws.
*Make sure heater guard is level before securing.
19