Durabook R8 User manual

©2023 Twinhead International Corp and/or its affiliates. All rights reserved.
1
R8 Rugged Tablet
Expansion Module
Smart Card Reader
with RFID
Smart Card Reader with LF/HF RFID Smart Card Reader with UHF RFID
P/N: 62+031105+10

R8 Expansion Module - Smart Card Reader with RFID
2
Package Contents
If any of following items is damaged, please contact your retailer.
Smart Card Reader with
RFID module
Screw
(7+1+3)
Sponge
or
Expansion Module - Smart Card Reader with RFID Screws
Screw Name
Screw Type
Quantity
Torque
ISOT-M2.0X6L
7
2.0 ± 0.3 Kgf-cm
ISOT-M2.0X8L
1
2.0 ± 0.3 Kgf-cm
ISOT-M2.0X5L,
D=3.4mm
3
2.0 ± 0.3 Kgf-cm
NOTE
The pictures are for reference only, actual items may slightly differ.

R8 Expansion Module - Smart Card Reader with RFID
3
Installation
This section will guide you on how to install the expansion modules to your tablet
PC.
Note: Make sure to remove the battery before installing any type of expansion
modules. For more information on how to remove/install the battery, please refer
to the tablet PC service guide.
Installing the Expansion Module - Smart
Card Reader with RFID
1. Remove the screw securing the mylar on the lower case.
2. Attach the expansion sponge to the lower case.

R8 Expansion Module - Smart Card Reader with RFID
4
3. Connect the expansion module with smart card reader harness to the
mainboard connector.
4. Place the expansion module with smart card reader bracket onto its slot on
the lower case. Make sure the cut edge of the bracket is aligned properly
with the lower case.
5. Attach the 3 screws to secure the expansion module with smart card reader
bracket to the lower case.
➢ISOT-M2.0X5L, D=3.4mm (marked with C): 3 screw.

R8 Expansion Module - Smart Card Reader with RFID
5
6. Route the expansion module with smart card reader cable as shown in the
image below.
7. Align by the screw holes and then place the expansion module with smart
card reader on top of its bracket.
8. Attach the 6 screws to secure the expansion module with smart card reader
to the lower case.
➢ISOT-M2.0X6L (marked with B): 6 screw.

R8 Expansion Module - Smart Card Reader with RFID
6
9. Slide the expansion module with smart card reader lock switch to the unlock
position.
10. Open the smart card reader door.
11. Attach the 2 screws to secure the smart card reader to the lower case.
➢ISOT-M2.0X8L (marked with A): 1 screw.
➢ISOT-M2.0X6L (marked with B): 1 screw.

R8 Expansion Module - Smart Card Reader with RFID
7
12. Close the expansion module with smart card reader door.
13. Slide the smart card reader lock switch to the lock position.

R8 Expansion Module - Smart Card Reader with RFID
8
Expansion Module - Smart Card Reader with RFID Screws
Screw Name
Screw Type
Quantity
Torque
ISOT-M2.0X6L
7
2.0 ± 0.3 Kgf-cm
ISOT-M2.0X8L
1
2.0 ± 0.3 Kgf-cm
ISOT-M2.0X5L,
D=3.4mm
3
2.0 ± 0.3 Kgf-cm
Twinhead International Corp.
11F, No.550, Ruiguang Rd., Neihu, Taipei 11492, Taiwan, R.O.C.