Durabrand CDR-1902 User manual

IB-CDR1902(TA)-WM-E-090902
CD PLAYER
DUAL ALARM DIGITAL CLOCK RADIO
OPERATING INSTRUCTIONS
DUAL ALARMS - PERFECT FOR WEEKDAYS & WEEKENDS
PLAYS MUSIC COMPACT DISCS
FULLY PROGRAMMABLE CD PLAYER WITH REPEAT
RECEIVES AM/FM BROADCASTS
WAKE UP TO CD, RADIO OR BUZZER
EASY TO SET CLOCK
BATTERY BACK-UP (9V BATTERY NOT INCLUDED)
PLEASE READ CAREFULLY BEFORE USE
MODEL CDR-1902

IB-CDR1902(TA)-WM-E-090902
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT USE THE PLUG WITH AN EXTENSION CORD,
RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT
BLADE EXPOSURE. TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE
TO RAIN OR MOISTURE.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings, install in accordance with the manufacturers
instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug
has two blades with one wider than the other. A grounding type plug has two blades and a
third grounding prong. The wide blade or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid
injury from tip-over.
1
WARNING
IMPORTANT SAFETY INSTRUCTIONS
The lightning flash with
arrowhead symbol, within an
equilateral triangle, is intended
to alert the user to the presence
of uninsulated dangerous
voltage within the products
enclosure that may be of
sufficient magnitude to
constitute a risk of electric
shock to persons.
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO REDUCE THE
RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR
BACK). NO USER SERVICEABLE
PARTS INSIDE. REFER
SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The exclamation point within an
equilateral triangle is intended
to alert the user to the presence
of important operating and
maintenance (servicing)
instructions in the literature
accompanying the appliance.
13. Unplug this apparatus during lightening storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate
normally or has been dropped.
15. This appliance shall not be exposed to dripping or splashing water and that no object filled with liquid
such as vases shall be placed on the apparatus.

IB-CDR1902(TA)-WM-E-090902
ADDITIONAL SAFETY INSTRUCTIONS
1. Power Sources - The appliance should be connected to a power supply only of the type
described in the operating instructions or as marked on the appliance.
2. Wall or Ceiling Mounting - The appliance should not be mounted to a wall or ceiling.
3. Object and Liquid Entry - Care should be taken so that objects do not fall and liquids
are not spilled into the enclosure through openings.
4. Servicing - The user should not attempt to service the appliance beyond that described in the operating
instructions. All other servicing should be referred to qualified service personnel.
5. Do not connect FM antenna wire to any outdoor antenna.
CAUTION
Use of controls or adjustments or performance of procedures other than those specified
herein may result in hazardous radiation exposure.
This compact disc player is classified as CLASS 1 LASER PRODUCT as stated on the
bottom of the set.
Do not apply oil or petroleum products or solvents to any part of this set.
2

IB-CDR1902(TA)-WM-E-090902
1. Setting the Clock
1Connect the AC power cord into a live wall outlet.
3Hold the TIME button down,
and press the MINUTE
button until the right minute
time shows in the display.
Hold the TIME button down,
and press the HOUR button,
until the right hour time shows
in the display.
2
Clock display will show 12:00 .
PM indication lights up
for PM time.
If the plug of the AC power cord does not
match your outlet, do not force it.
Reverse it and try again. This plug is
polarized and only fits one way into the
wall outlet.
Example: 10:26 p.m.
CLOCK/CD
DISPLAY
TIME BUTTON
Refer to Page 10 Part 8. Setting the Alarm Times for setting alarm time.
3
MINUTE BUTTON HOUR BUTTON

IB-CDR1902(TA)-WM-E-090902
2. Playing a CD
1Press the POWER
button to turn on the
power, make sure the
POWER lamp is on.
Slide the FUNCTION
switch to CD position.
3Close the CD DOOR by
pushing it down at the right
corner. The display will show
the total track number of the
disc for 5 seconds, then go
back to clock time display.
4
Press the CD DOOR
OPEN button to open the
CD Door and place the CD
in the CD compartment.
The label side of the CD
should face upward.
2
Press the CD PLAY button. The
player plays all the tracks once.
Press the CD DISPLAY button,
the display will show the track
number of current play.
Connect the AC power cord (see Setting the Clock).
CD Track
number
CD DOOR
OPEN button
CD PLAY button
4
CD DISPLAY
button
POWER
button
FUNCTION switch
(on the left side)
POWER
lamp
total track number
of the disc
During CD play, the display still shows CLOCK time, press CD DISPLAY
button if you want CD display.
CLOCK/CD
DISPLAY

IB-CDR1902(TA)-WM-E-090902
Use these buttons for additional operations
To Press or Adjust
Adjust the volume Volume Control
Stop playback
Pause playback
CD track number will flash
during pause. Press again
to resume play after pause.
Go to the next track
Go back to the previous
track
Locate a point in a song or while playing,
press and hold down until
you find the point.
Tip
When CD play is
paused, the CD
track number will
flash and no music
will play.
Remove the CD CD DOOR OPEN button
(press first).
VOLUME
CONTROL
CD DOOR
OPEN button
Turn off the CD player Press the POWER button
to turn off the power, the
POWER lamp will be off.
To resume play,
press the PAUSE
button again, CD
track number will
stop flashing and
music will play.
CD Track
3. More about CD operation
5
POWER
button
POWER
lamp
STOP
PLAY/PAUSE
SKIP/SEARCH
FORWARD
SKIP/SEARCH
BACKWARD

IB-CDR1902(TA)-WM-E-090902
4. Playing CD tracks repeatedly (Repeat Play)
To repeat Press (during play)
a single track (song) Press the REPEAT button once
all the tracks (all songs) Press the REPEAT button twice
1. Press the POWER button to turn on the power and slide the FUNCTION switch to
CD position.
2. Press (PLAY button).
3. Press the CD REPEAT button.
To cancel Repeat Play
Press the REPEAT button until the REPEAT lamp is off.
4. You may select the individual track to repeat by pressing or .
REPEAT button
FUNCTION switch
(on the left side)
Repeat Lamp
Steady on
Flashing
6
POWER
button
REPEAT
lamp

IB-CDR1902(TA)-WM-E-090902
5. Playing CD in programmed order
To cancel Programmed Play
Press the STOP button to stop programmed play. Press the STOP button again after
pressing the PROGRAM button or press the CD DOOR OPEN button to open the CD
door, and the PROGRAM lamp goes off.
7
You can make a program of up to 20 tracks in the order you want them to be played.
PROGRAM
lamp
PROGRAM
button
1. Press the POWER button to turn on the power
and slide the FUNCTION switch to CD position.
Make sure the CD is stopped.
2. Press the PROGRAM button. The letters
P01 will show and the PROGRAM lamp will
flash.
3. Press or to select the tracks you want
to program in the order you want.
4. Press the PROGRAM button to confirm. The
letters P02 will show.
5. Repeat steps 3 and 4. You can program up to
20 tracks.
6. Press to start programmed play. The
PROGRAM lamp will show steadily on the
display.
To change the current program
Just create a new program following the programming procedure.

IB-CDR1902(TA)-WM-E-090902
6. Listening to the radio
Connect the supplied AC power cord (see Setting the Clock).
Press the POWER button to
ON and slide the FUNCTION
switch to RADIO position.
1
2
3
Slide the BAND switch to the proper
band position that you want.
Tune into the station you prefer using
the TUNING CONTROL. Adjust for the
clearest sound.
VOLUME
CONTROL
FUNCTION
SWITCH BAND
SWITCH
TUNING
CONTROL
Adjust the VOLUME CONTROL for
desired loudness.
Press the POWER button to turn off the
power and the Radio, the POWER lamp
will go off.
4
5
8
LEFT SIDE VIEW RIGHT SIDE VIEW

IB-CDR1902(TA)-WM-E-090902
To improve broadcast reception
FM ANTENNA
Fully stretch out the FM ANTENNA for better FM reception.
Reorient the player itself for better AM reception.
Or locate the set near a window.
7. More about radio operation
BATTERY COMPARTMENT
(at the bottom of the set)
PHONES jack
To listen without disturbing others
Connect your headphones (optional - not included) into the PHONES jack at the back
of the set. The speaker will automatically be silenced. Remember to unplug the
headphones if you want the set to wake you up in the morning.
To use battery backup
Install a 9V battery for Clock backup, so that if your home power is momentarily off, you
will not have to set up the time & alarm settings.
Note: The display will not show the time but the time will be kept in memory and will re-
appear when power is restored.
9