Duraline Systems Vistacool NSVC-1 User manual

Model NSVC-1
For 1
Autoclave
Installation Guide & Owner’s Manual
Direct-to-Drain Thermal Reduction
System for Autoclave Wastewater
Model NSVC-2
For 2
Autoclaves
VistaCool can be used with:
Midmark/Ritter M3 SciCan STATIM 2000
Midmark/Ritter M9* SciCan STATIM 5000
Midmark/Ritter M11*
* Requires Model V7502 and S7560 adapter kit

2Installation Guide & Owner’s Manual
TM
Table of Contents
Introduction ....................................................................................................................................................................3
Important Information ..................................................................................................................................................3
Preparation - V7501 .......................................................................................................................................................4
Preparation - V7502 ......................................................................................................................................................5
Typical Installation - V7501 ..........................................................................................................................................6
Typical Installation - V7502 ..........................................................................................................................................7
Plumbing ......................................................................................................................................................................... 8
Cabinetry ..........................................................................................................................................................................9
Connecting the System ..............................................................................................................................................10
Tank Positioning ...........................................................................................................................................................12
Starting & Using the System .......................................................................................................................................12
Autoclave-Specific Instructions ................................................................................................................................13
Maintenance ..................................................................................................................................................................14
Troubleshooting ...........................................................................................................................................................14
VistaCool Limited Warranty .......................................................................................................................................15
VistaCool System Information & Specifications ....................................................................................................16
39 Western Hwy.
West Nyack, NY 10994
www.DuralineSystems.com
877-561-0500

3
VistaCool is a patent-pending system designed to eliminate the
need for autoclave condenser/waste bottles and condensation
tanks by cooling the exhaust water and automatically sending it
directly down the drain. With the use of a simple adapter kit, the
VistaCool Model V7502 is designed to enable the Midmark/Ritter
M9 and M11 autoclaves to use fresh deionized/distilled water for
each sterilizing cycle—converting these chambered autoclaves to
operate like quick-turnaround, cassette systems.
Introduction
VistaCool can be used with:
Midmark/Ritter M3
Midmark/Ritter M9*
Midmark/Ritter M11*
SciCan STATIM 2000
SciCan STATIM 5000
We recommend that a professional technician or plumber familiar with dental/medical oces perform the
installation since interface with a cold water line and drain is involved. He/she should be familiar with local
plumbing codes and techniques for successful dental/medical equipment installations. Failure to install
correctly could result in water leaks, leading to possible water damage. It is the responsibility of the system
owner to validate the use of all equipment within its installed environment.
Please keep the Installation Guide & Owner’s Manual handy for future reference and ensure that anyone
responsible for operation and maintenance of the system is familiar with all details contained in this manual.
Please return the Warranty Registration form or register online immediately upon installation.
IMPORTANT INFORMATION
For System Owners
Please read this entire manual before proceeding with installation and operation, and always follow local
plumbing codes.
VistaCool systems have only been verified for installation on the compatible autoclaves (listed above).
Please check with the manufacturer of other brands of autoclaves or contact Vista Research Group before
connecting to other than SciCan or Midmark/Ritter autoclaves. See page 13 for autoclave-specific instructions.
VistaCool Model V7502 has been verified for installation on Midmark/Ritter M9 & M11 units with the
use of the S7560 adapter kit. Only M9, M9D, M11 and M11D (-02X, -03X) units with green displays can
be connected to VistaCool. First generation models with red displays (-0XX) are not compatible.
The VistaCool tank must be installed so that the top of the water tank is ABOVE the connection to the
drain adapter. Please see page 12 for important tank positioning details.
Check for leaks and run the autoclave(s) for at least two consecutive cycles after installation to
ensure the system is operating properly.
IMPORTANT INFORMATION
For System Installers
* Requires Model V7502 and S7560 adapter kit

4Installation Guide & Owner’s Manual
TM
Preparation / V7501
Remove all contents from the VistaCool product carton to make certain all items needed
for installation are present and undamaged.
S6155
Water Supply Valve
S7570
M3 Mono Plug
S7508
Inline Thermal
Sensor Assembly
VC250-A
VistaCheck Dual Check
Backflow Preventer
S7506
Drain Line Assembly
S7539
Cabinet Grommet
x4
TU751
Cold Water Feed Line
⁄” OD x ⁄” ID
Blue Transparent Polyurethane
6’ TU753
Condensate Drain Line
⁄” OD x 0.170” ID
Black Opaque LLDPE
6’ TU755
Coolant Overflow Drain Line
⁄” OD x ⁄” ID
Clear PVC
6’
Tubing
TU748
High Temperature Feed Line
⁄” OD x 0.185” ID
Teflon®
9’
For 1
Autoclave
S6130
Plug
S6135
Angle Stop Adapter
S6119
3/8” x 3/8” x 1/4” Tee Union

5
Preparation / V7502
Remove all contents from the VistaCool product carton to make certain all items needed
for installation are present and undamaged.
S6155
Water Supply Valve
S7570
M3 Mono Plug
S7508
Inline Thermal
Sensor Assembly
VC250-A
VistaCheck Dual Check
Backflow Preventer
S7506
Drain Line Assembly
x2
x2
Tubing
18’
TU751
Cold Water Feed Line
⁄” OD x ⁄” ID
Blue Transparent Polyurethane
6’ TU753
Condensate Drain Line
⁄” OD x 0.170” ID
Black Opaque LLDPE
6’ TU755
Coolant Overflow Drain Line
⁄” OD x ⁄” ID
Clear PVC
6’ TU749
High Temperature Feed Line
⁄” OD x 0.185” ID
Teflon®
x2
For 2
Autoclaves
S7539
Cabinet Grommet
x8 S6130
Plug
S6135
Angle Stop Adapter
S6119
3/8” x 3/8” x 1/4” Tee Union

6Installation Guide & Owner’s Manual
TM
Typical Installation / V7501 For 1
Autoclave
Hot
Cold
Alternate Cold Water
Line Fitting Installation
AUTOCLAVE
1
2
3
5 6 7
8 9
10
12
11
4
Drain Line
Sink Drain
S7506
Drain Line Assembly
S6119 or S6135
Cold Water Line Fitting
1
2
3
4
S6155
Water Supply Valve
5
VC250-A
VistaCheck Backflow Preventer
6
TU751
Cold Water Feed Line
7
S7508
Inline Thermal Sensor Assembly
8
TU753
Condensate Drain Line
9
TU755
Coolant Overflow Drain Line
10
Manifold Coil Assembly
11
Thermal Regulator Assembly
12
4

7
Typical Installation / V7502 For 2
Autoclaves
AUTOCLAVE
AUTOCLAVE
Hot
Cold
Alternate Cold Water
Line Fitting Installation
1
2
3
5 6 7
8 9
10 11
12
11
4
Drain Line
Sink Drain
S7506
Drain Line Assembly
S6119 or S6135
Cold Water Line Fitting
1
2
3
4
S6155
Water Supply Valve
5
VC250-A
VistaCheck Backflow Preventer
6
TU751
Cold Water Feed Line
7
S7508
Inline Thermal Sensor Assembly
8
TU753
Condensate Drain Line
9
TU755
Coolant Overflow Drain Line
10
Manifold Coil Assembly
11
Thermal Regulator Assembly
12
4

8Installation Guide & Owner’s Manual
TM
1” MINIMUM
HOT COLD
Plumbing
Whether installing a single or double-autoclave VistaCool unit, the cold water (coolant) supply and drain
(condensate and coolant overflow) connections are exactly the same.
NOTE:
When installing the black ⁄” OD condensate line with a V7501 system, make sure to install the white ⁄”
plug in the remaining open fitting on the adapter to prevent water from flowing out of the drain. When
installing a V7502 system, connect a black condensate line to each of the two ⁄” push-to-connect
fittings and set the white plug aside.
Turn o water supply. Provide for a 1/4” connection
to the cold water supply. This is usually accomplished
using a compression fitting or one of the supplied fittings
(S6119 or S6135) on the cold water line.
Cut a 3” to 4” piece of the blue poly tubing and connect
the installed fitting (from step 1) to the inlet of the inline
water valve provided. Be certain the valve is in the closed
position (blue lever 90-degrees to the valve body).
Cut another 3” to 4” piece of blue poly tubing and
connect one end to the outlet end of the inline valve,
and the other end to the inlet of the supplied CSA-
certified VistaCheck dual check backflow preventer.
1
2
3
To Coolant Overflow
Barb on Top of Tank
Always slope lines downward toward drain.
To VistaCool Manifold
1 2 3
A
A
B
B
S6130P
Plug
Connect VistaCool to cold water supply ahead of foot switch (if present) for uninterrupted water supply!
4
Measure the drain tee adapter
assembly for placement into the
drain piping. Cut and remove
a section (usually 1-1/2”) in the
appropriate place above the trap as
shown. Keep the entire assembly as
low as possible while maintaining a
minimum of 1” oset from the barb
fitting as shown. Rotate the drain
adapter hub so the barb fitting is at
the 6:00 position.
Be sure to tighten slip-joint tee’s
nuts once all steps are complete.
4

9
Cabinetry
VistaCool systems are typically installed in the base/sink cabinet of sterilization centers. The systems should
always be installed as close to the drain system and cold water supply line as possible. The 1/4” O.D. Teflon
high temperature tubing will need to run from the output port of the autoclave directly to the VistaCool
system. In many cases, holes will need to be drilled through one or more partitions in order to get the tub-
ing from the autoclave to the VistaCool.
In order to protect the tubing from kinking or damage, grommets have been included with each system.
Many cabinets are constructed of composite wood and some are metal. It’s especially important to use the
grommets to line the edges of the drilled holes in metal cabinets to keep the tubing from being damaged.
Simply drill a 7/8” pilot hole through the metal or wood partition then push the smooth plastic grommet
into the holes. Make sure to drill the holes so that the tubing makes a progressively descending angle from
the autoclave to the VistaCool. The hole entering the cabinet where the VistaCool is installed should be
above the top of the tank manifold so the tubing has a natural gravity angle to help prevent pools of liquid
in the tubing.
NOTE:
A 9’ length of the high temperature Teflon tubing is included with each single (V7501) and an 18’ length is included
with each double (V7502) VistaCool system. An additional 18’ length of Teflon tubing is available as an accessory
(TU749). Do not exceed 10’ in length for any individual section of tubing between an autoclave and the VistaCool.
Always try to minimize the length of run of tubing to reduce friction and prevent “traps” and pooling in the lines.
AUTOCLAVE
USE ⁄”
HOLE SAW

10 Installation Guide & Owner’s Manual
TM
Connecting the System
• All tubing cuts must be even and clean.
• Most fittings are a push-to-connect design. Use a twisting motion when pushing tubing into
the fittings to ensure ends are fully inserted through the collet and into the internal “O” ring.
• Several fittings are a hose barb design. The ⁄” metal barbs are extremely strong and tight when the tubing is
pushed on. If you must remove the tubing for any reason, make a cut along the edge of the tubing at the barb
then remove, make a fresh cut and reinstall.
• The remaining barb connections are thermoplastic, and the tubing should be held in place suciently by being
stretched over the barbs since there is no pressure in the lines. However, if you feel the tubing could be pulled
during normal use, you may wish to install a stainless hose clamp to hold the tubing firmly in place.
• Do NOT use Vaseline or other lubricants (other than clean water) on the tubing. Moisten the tubing ends with
water before inserting tubing into push-to-connect fittings if lubrication is needed.
• Cut the tubing to a sucient length so that no tubing line is tight or stressed, and so the VistaCool tank
assembly can be moved within the cabinet easily.
• Tubing connecting to the drain (both the condensate lines and coolant line) should be as short as possible and
must not droop, loop or sag in a way that would form a trap that could cause flow restriction or backpressure.
• Ensure that fluid flow is not impeded by kinked or bent tubes.
• Manually FILL THE TANK before starting the system. See below.
1. Fill the water tank COMPLETELY. Remove the manifold and coil assembly from the tank by twisting
the manifold counter clockwise. Fill the tank with COLD water, replace the coil manifold into the open
hole and place the tank into position under the sink.
1
1