Duratech DURALINK PL-REM-60 User manual

PL-REM-60
Manual
LINK Driver
12-09-22

2
Table of contents
Technical specifications
Box contents
Installation instructions
Pairing Handheld Transmitter & controller
Handheld transmitter functions
Replacing transmitter battery
Troubleshooting
Page 3
Page 4
Page 5
Page 6
Page 7
Page 7
Page 8

3
Technical specifications
Electrical specifications
Nominal Input voltage
Output voltage on Lamp Output
Max output current on Lamp Output
Transformer VA rating
Frequency band transmitter
IEC Protection Class
General specifications Controller
Ambient air temperature
Humidity
Dimensions
Weight
Ingress Protection Rate
230 VAC 50 Hz
12 VAC
5A
60VA
868 MHz
Class II
0°C ... +40°C
10% ... 90% RH
non condensing
150x157x51 mm
1,3 kg
IP54

4
Box contents
12
4
5
1. PL-REM-60 controller
2. Handheld transmitter
3. Spare battery
4. Screws (4x) & wall plugs (4x)
5. Owner’s Manual
3

5
Installation instructions
• Connect a 230VAC power source to the “220-240VAC INPUT”
terminal.
• Connect the swimming pool lights to the “Lamp 12VAC output”
terminal
Make sure the total load of pool lights does not exceed 60Watt
230VAC

6
Green LED
Pairing button
Pairing handheld transmitter & controller
The handheld transmitter is already paired in the factory and ready to
use. The PL-REM-60 can pair with up to 6 handheld transmitters. In
case a problem arises, the pairing process can be done manually:
Manual Pairing process:
Make sure the PL-REM-60 is connected to a power source.
1. Press the pairing button on the small circuit board, inside the con-
troller for at least 5 seconds.
--> The LED will start to blink fast
2. Within 25 seconds, press any button on the handheld transmitter.
--> If the transmitter is paired correctly, the LED will flash slowly for 5 times
--> If the PL-REM-60 pairing memory is full, the LED will flash 15 times.
This means 6 handheld devices have already been paired.
To unpair all handheld transmitters with the controller: Push the pair-
ing button for at least 5 seconds, then do nothing for at least 25 sec-
onds.
--> The pair memory will be erased - the green LED will flash 5x on/o.
If no transmitters are paired, the PL-REM-200 will accept messages from any transmitter!

7
Handheld transmitter functions
Pairing button
Toggle the lamps ON/OFF
Go to next color scenario
Button A and B have no
function with PL-REM-60
Replacing transmitter battery
• Remove the philips head screw and open the transmitter
• Replace the battery, respecting the polarity
Battery type: A23 12V
-
+

8
PROBLEM SOLUTION
The controller doesn’t react
to transmitter commands
• Check the battery of the hand-
held transmitter
• The transmitter is not paired
correctly with the controller.
Repeat the pairing process
• Reduce the distance between
handheld transmitter and PL-
REM-60 and/or eliminate ob-
stacles
The pool lights don’t work • Check the red status LED
• Check if there is 12VAC output
at the terminals of the controller
Troubleshooting

9
Declaraction of Conformity
Declarations of conformity covering this product are available for
download from the House of Duratech website: www.duratech.be

10
Notes

11
VISION Moonlight
VISION Spectra
VISION Adagio Pro
VISION Wall Conduits
VISION Faces Plates
VISION Specials
COVER Tube
COVER Wall Duct
COVER Motor
VISION Pro
HEAT Hot Splash
HEAT Sun Spring
HEAT Dura +i
HEAT Dura Vi
HEAT Dura V
HEAT Dura Pro
HEAT Accessories
LINK Touch
LINK Driver
LINK Master
LINK Controller
LINK Accessoires
LINK Cover
FLOW Inverter
COVER Hanging System
COVER Cable Duct

Contact details
Propulsion Systems bv
Dooren 72
1785 Merchtem, Belgium
Tel [phone]
www.duratech.be
[email protected]
We reserve the rights to change all or part of the contents of this document without prior notice
402-0081-2