DVDO DVDO-Xtend-TX100 User manual

3
DVDO-Xtend-TX100_V1.0.0
DVDO
DVDO-Xtend-TX100 3 x 1 HDBT Wall-plate Transmitter User Manual
Table of Contents
Introduction...................................................................................................... 4
Overview................................................................................................... 4
Features ................................................................................................... 5
Package Contents .................................................................................... 6
Specifications ........................................................................................... 7
Panel Description ..................................................................................... 9
Installation and Wiring ................................................................................... 11
Input Switching .............................................................................................. 13
API Command Control................................................................................... 14
DVDO Product Configuration Tool ................................................................. 16
Warranty Terms and Conditions..................................................................... 18

4
DVDO-Xtend-TX100_V1.0 0
DVDO-Xtend-TX100 3 x 1 HDBT Wall-plate Transmitter User Manual
DVDO
Introduction
Overview
This product is an HDBaseT 2.0 wall plate transmitter for HDMI inputs and
HDBaseT 2.0 output. HDMI signals up to 4K@60 (YUV 4:2:0 color
sub-sampling). It supports signal transmission up to 90m/300ft for 4K and
100m/330ft for 1080P via signal Cat 5e/6 cable, and supports signal
transmission up to 100m/330ft for 4K and 1080P via single Cat 6a/7 cable.
With USB 2.0 pass-through, it provides solution where users want to control a
remote server or connect to an electronic whiteboard. And additional analog
audio pass-through allow the audio distribution to the receiver side.
The wall plate can be the central component of a small, automated AV system.
Automatic display control turns-on the display automatically whenever a source
is connected. When the source is removed, the display is turned off. Automatic
input selection on the wall plate works by sensing the presence of any video
signal. With automatic input selection, manual control systems can be eliminated.
With 48V PoH integrated inside, it can be powered either by local power supply
or remote HDBaseT receiver with PSE module.

5
DVDO-Xtend-TX100_V1.0.0
DVDO
DVDO-Xtend-TX100 3 x 1 HDBT Wall-plate Transmitter User Manual
Features
Three HDMI inputs and one HDBT output
Auto switching technology
One-way analog audio pass-through from transmitter to receiver
Via Cat 6/6a/7 cables, transmits 4K@60Hz (YUV 4:2:0 color sub-sampling)
and 1080P@60Hz signals up to 100m/330ft
Via Cat 5e cable, transmits 4K@60Hz (YUV 4:2:0 color sub-sampling)
signal up to 90m/300ft, while 1080P@60Hz up to 100m/330ft
HDMI with 4K@60Hz (Chroma sub-sampling 4:2:0 8-bit only) and HDCP
2.2 compliance
Support Long Reach Mode function, extend 1080p@60Hz signal to
150m/493ft by API command
High-speed USB 2.0, up to 480Mbps, pass through over HDBaseT up to
100m/330ft
2-Gang US Decora wall-plate
With PoH support to be powered by any HDBaseT device with PSE module
Firmware upgrade via Micro USB for easy filed service

6
DVDO-Xtend-TX100_V1.0 0
DVDO-Xtend-TX100 3 x 1 HDBT Wall-plate Transmitter User Manual
DVDO
Package Contents
Before you start the installation of the product, please check the package
contents as below:
DVDO-Xtend-TX100 Transmitter x 1
Phoenix Male Connector (2 Pins, 3.5mm) x 1
USB B to USB A Cable x 1
#6-32*20mm Screws, Silver x 4
#6-32*7mm Screws, White x 4
Wall Plate Plastic Panel (2-gang US) x 1

11
DVDO-Xtend-TX100_V1.0.0
DVDO
DVDO-Xtend-TX100 3 x 1 HDBT Wall-plate Transmitter User Manual
Installation and Wiring
Warnings:
Before wiring, disconnect the power from all devices.
During wiring, connect and disconnect the cables gently.
Steps for device wiring:
1. Connect HDMI sources (such as Blu-ray, DVD, HDD, camera, games
console, Satellite/cable TV, computer, media server etc.) to the Transmitter.
2. Connect a good quality, well-terminal Cat 5e/6/6a/7 cable from the HDBT
OUT port of the transmitter to HDBT IN Input of an HDBT Receiver with PSE
module.
Note: 90m @4K or 100m @1080p video are maximum recommended
transmission distances for this model and denotes perfect transmission
conditions – including straight cable runs with no electrical interference, bends,
kinks, patch panels or wall outlets.
If any of the above is a factor in your installation, transmission range may be
affected – take care to avoid where possible.
3. Connect the USB port to the PC, at the same time connect the receiver's
USB ports to USB devices (such as keyboard, mouse and interactive
whiteboard) to realize the remote control.
4. Connect an HDMI display device (LED/LCD display or projector) to the
HDMI OUT of your HDBT Receiver.
5. Connect for additional control options:
• USB Control: Connect a host PC to USB B port on front panel of the
transmitter, connect USB devices such as USB camera, keyboard,
mouse to USB DEVICE ports of receiver, the USB devices can be
connected to host PC.
• API Command Control: Connect Micro USB B port to USB port of PC via
the USBBto USB A cable. Or connect a control PC to the receiver.
More information, see “API Command Control” section.
6. Power on the HDBT receiver which support PoH function, it will power to
Transmitter.

13
DVDO-Xtend-TX100_V1.0.0
DVDO
DVDO-Xtend-TX100 3 x 1 HDBT Wall-plate Transmitter User Manual
Input Switching
The transmitter supports automatic switching and front panel button switching.
When it is powered on, automatic switching will function as follows:
1. When HDMI sources are inserted, the switcher will follow the rule: last in,
first out, switch to the latest connected source for output display.
2. When the HDMI source selected is removed, the switcher will switch to the
active source with top priority for output display (Default priority: HDMI
IN1>HDMI IN2>HDMI IN3).
3. The front panel SELECT INPUT button is used for selecting input source
when HDMI video signals are valid.
Note: Automatic Switching function can only detect 5V of the input source
device. If the selected HDMI source in standby mode provides a continuous 5V
power output, the Automatic Switching function will not work, i.e. the switcher
will not switch the input to other active sources. In this case, please turn off the
standby source device selected or remove it from the switcher.

14
DVDO-Xtend-TX100_V1.0 0
DVDO-Xtend-TX100 3 x 1 HDBT Wall-plate Transmitter User Manual
DVDO
API Command Control
Users can control the device via sending API commands as well. Please refer
to the following steps.
1. Connect the HDBT OUT of the transmitter to HDBT IN of receiver, the
transmitter can be powered by receiver via Cat X cable.
2. Use the Micro USB-B to USB-A cable provided to connect the UPDATE
port of the transmitter and your PC USB port. Or connect a PC to RS232
port of the connected receiver. It is ready for sending API commands.
3. Open your PC Device manager, find out the port, here is COM 2 as
example.
4. Install serial tool to your local folder ( Ta k e “UartAssist” tool as an
example).
5. Open the tool and type the port number COM 2 and Baud Rate 115200.

15
DVDO-Xtend-TX100_V1.0.0
DVDO
DVDO-Xtend-TX100 3 x 1 HDBT Wall-plate Transmitter User Manual
6. Click Open, the button will become red for operation.
Type the commands in the data transmit window, for example “GET
SW_VERSION”, click your PC Enter button and click the Uart To ol Send button,
the Data receive window will show the response.
Note: More information please refer to the API Command
Set_DVDO-Xtend-TX100.

16
DVDO-Xtend-TX100_V1.0 0
DVDO-Xtend-TX100 3 x 1 HDBT Wall-plate Transmitter User Manual
DVDO
DVDO Product Configuration Tool
The transmitter supports configuration through the “DVDO Product
Configuration Tool”.
1. Connect the HDBT OUT of the transmitter and your receiver HDBT IN, the
transmitter can be powered by receiver via Cat X cable.
2. Use the Micro USB-B to USB-A cable provided to connect the transmitter
UPDATE port and your PC USB port. Or connect a PC to RS232 port of
receiver.
3. Check which port on the computer the cable is connected to in the device
manager.
4. Copy the “DVDO Product Configuration Tool” to local file.
5. Run the tool, and set the connection parameters correctly before sending
any commands to the transmitter.
Select right port from the drop-down menu, and set the baud rate, then
press Connect. Once connected you can set the RS232 output port
commands and the relay mode.
Note: When connect the PC via UPDATE port of the transmitter, the Baud
Rate is fixed according to the transmitter, and connect PC via RS232 port
of Receiver, you can set baud rate.

17
DVDO-Xtend-TX100_V1.0.0
DVDO
DVDO-Xtend-TX100 3 x 1 HDBT Wall-plate Transmitter User Manual
“DVDO Product Configuration Tool” menus are described below:
• Get current settings:Get the current settings of the sink device.
• Baud rate: Choose the correct baud rate according to the device, then click
“Connect” to connect with the sink device.
Note:This might be different than the setting of 115200 above and is
determined by the sink device you are connecting to.
• Power on: Pre-load and store the command for “power on” to a sink device,
then click “Send” to send and store it on the device.
• Power off: Pre-load and store the command for “power off” to a sink device,
then click “Send” to send and store it on the device.
Note: If the sink device requires hex commands, make sure the Hex box is
checked.
• Delay: Set delay time (1~30minutes) the sink device will power off
automatically after it cannot detect the input signal, click “set” to take effect.
• Set Terminator: Select the command ending after each API command that
you are sending from the transmitter or receiver to the sink device. Then
click “Set” to take effect.
• Set Relay Mode: Set relay mode for the sink device.
Latch –relay closes and latches when it is triggered;
Momentary –only closes for a moment and then opens after it is triggered.
The pulse time can be set from 1 to 10 seconds, default setting is 3s.
Then click “Set” to take effect.

18
DVDO-Xtend-TX100_V1.0 0
DVDO-Xtend-TX100 3 x 1 HDBT Wall-plate Transmitter User Manual
DVDO
Warranty Terms and Conditions
For the following cases we shall charge for the service(s) claimed for the
products if the product is still remediable and the warranty card becomes
unenforceable or inapplicable.
1. The original serial number (specified by us) labeled on the product has
been removed, erased, replaced, defaced or is illegible.
2. The warranty has expired.
3. The defects are caused by the fact that the product is repaired,
dismantled or altered by anyone that is not from an authorized service
partner. The defects are caused by the fact that the product is used or
handled improperly, roughly or not as instructed in the applicable User
Guide.
4. The defects are caused by any force majeure including but not limited to
accidents, fire, earthquake, lightning, tsunami and war.
5. The service, configuration and gifts promised by salesman only but not
covered by normal contract.
6. We preserve the right for interpretation of these cases above and to make
changes to them at any time without notice.