DW DWC-HF21M4TIR User manual

12112013
ABOUT MANUAL
Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for future reference.
HD-SDI Vandal Dome Camera
DWC-HF21M4TIR

2
PRECAUTIONS
Do not open or modify.
Do not open the case except during maintenance and installation,
for it may be dangerous and can cause damage.
Do not put objects into the unit.
Keep metal objects and flammable substances from entering the camera.
It can cause fire, short-circuits, or other damages.
Be careful when handling the unit.
To prevent damage, do not drop the camera or subject it to shock or vibration.
Do not install near electric or magnetic fields.
Protect from humidity and dust.
Protect from high temperature.
Be careful when installing near the ceiling of a kitchen or a boiler room,
as the temperature may rise to high levels.
Cleaning:
To remove dirt from the case, moisten a soft cloth with a soft detergent solution and wipe.
Mounting Surface:
The material of the mounting surface must be strong enough to support the camera.
FCC COMPLIANCE
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference, when the equipment is operated in a residential environment. This
equipment generates, uses, and radiates radio frequency energy; and if it is not installed and used in
accordance with the instruction manual, it may cause harmful interference to radio communications.
WARNING: Changes or modifications are not expressly approved by the manufacturer.

Troubleshooting
Warranty Information
Specifications
12
13-14
15
Table of Contents
3
TABLE OF CONTENTS
Introduction
Installation
Features
Parts and Descriptions
Dimensions
Inside the Box
Easy Installation
Connecting to Monitors
4
5
6
7
8-10
11

4
FEATURES*
1/2.8” CMOS Sensor
Highest Resolution 2.1 Megapixels (HD-SDI)
4.0mm Fixed Lens
12x Digital Zoom
30ft Range IR with Intelligent Camera Sync
TDN (True Day and Night/IR Cut Filter)
WDR (Wide Dynamic Range)
3D-DNR (3D Digital Noise Reduction)
IP66 Certified (Vandal Resistant)

PARTS & DESCRIPTION*
1Bottom Case
Camera Gimbal
Camera Lens + IR LEDs
Dome Cover
Dome Cover Screws (x3)
2
3
5
4
5
4
5
2
3
1

DIMENSIONS IN MILLIMETERS (IN)*
6
74.3 [2.9”]
40.2 [1.58”]
125.0 [4.9”]

Included with your Camera
5
6
8
7
1
2
3
4
L-Wrench
2 Mounting Nuts & 2 Mounting Screws
Metal Mount Plate
Secondary Video-BNC Cable
User Manual
Mounting Template for Metal Mount
Mount Template for Bolt Type Mount
3 Machine Screws and 3 Dry Wall Anchors
2
13 4
7
INSIDE THE BOX*
6
5
14
23
87
12112013
ABOUT MANUAL
Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for future reference.
HD-SDI Vandal Dome Camera
DWC-HF21M4TIR

EASY CAMERA INSTALLATION*
8
1. Detach the camera’s cover dome from
the camera’s module by unscrewing the
three cover dome screws.
2. Use the camera or mounting template
to mark and drill the necessary holes in
the wall or ceiling.
3. Pull wires through and make
connections.
4. Using the two (2) included screws,
mount and secure the camera to the wall
or ceiling.
5. Secure the camera’s cover dome onto
the camera base to complete the
installation.

EASY MOUNT BRACKET INSTALLATION*
Use the following installation instructions when
mounting the camera using the wall mount or
ceiling mount accesories.
1. Detach the camera’s cover dome from the
camera’s module by unscrewing the three
cover dome screws.
2. Using the metal mount plate, mark and drill
the necessary holes in the wall or ceiling.
3. Pull wires through and make connections.
4. Using the three (3) included screws, mount
and secure the camera to the wall or ceiling.
5. Attach the camera base to the metal
mount by snapping it into place using the two
metal handles.
6. Secure the camera’s cover dome onto the
camera base to complete the installation.
9

EASY SOFT CEILING MOUNT INSTALLATION*
1. Detach the camera’s cover dome from
the camera’s module by unscrewing the
three cover dome screws.
2. Secure the two long mounting screws
to the camera’s base.
3. Using the camera or mounting
template, mark and drill the necessary
holes in the wall or ceiling.
4. Pull wires through and make
connections.
5. Mount the camera to the mounting
surface using the 2 mounting nuts.
6. Secure the camera’s cover dome onto
the camera base to complete the
installation.
10
MOUNTING SURFACE