DW STAR-LIGHT AHD DWC-V7753WTIR User manual

09/16
ABOUT MANUAL
Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for future reference.
STAR-LIGHT AHDTM
Analog High Definition
Mini Outdoor Dome Camera
DWC-V7753WTIR
3W
T
3W
TIR

2
PRECAUTIONS
Do not open or modify.
Do not open the case except during maintenence and installation,
for it may be dangerous and can cause damages.
Do not put objects into the unit.
Keep metal objects and flammable substances from entering the camera.
It can cause fire, short-circuits, or other damages.
Be careful when handling the unit.
To prevent damages, do not drop the camera or subject it to shock or vibration.
Do not install near electric or magnetic fields.
Protect from humidity and dust.
Protect from high temperature.
Be careful when installing near the ceiling of a kitchen or a boiler room,
as the temperature may rise to high levels.
Cleaning:
To remove dirt from the case, moisten a soft cloth with a soft detergent solution and wipe.
Mounting Surface:
The material of the mounting surface must be strong enough to support the camera.
FCC COMPLIANCE
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference, when the equipment is operated in a residential environment. This
equipment generates, uses, and radiates radio frequency energy; and if it is not installed and used in
accordance with the instruction manual, it may cause harmful interference to radio communications.
WARNING: Changes or modifications are not expressly approved by the manufacturer.

Table of Contents
3
TABLE OF CONTENTS
Introduction
Installation
Module OSD Menu
Troubleshooting
Warranty Information
Specifications
Features
Parts and Descriptions
Dimensions
Inside the Box
Installation Instructions
Connecting to Monitors 10
Installation using Mount Bolt & Nut
Control Board
4
5
6
7
8
9
11
12
13-25
26
27-28
29-30
Adjusting the Camera Angle

4
FEATURES*
Analog High Definition (AHD) HD over Coax Technology
STAR-LIGHT™ Super Low Light Technology
Panasonic 1/3" CMOS Sensor
1080P Resolution at 30fps
Wide Dynamic Range (WDR)
Fixed P-Iris Lens 3.6mm
Smart IR™ with Intelligent Camera Sync. 50ft Range
Smart DNR™ 3D Digital Noise Reduction
Highlight Masking Exposure (HME)
True Day/Night Mechanical IR Cut Filter
Secondary Video-BNC Output (While UTP in use)
Easy Icon Driven OSD Menu with Built-in Joystick
Programmable Privacy Zones
Auto Gain Control (AGC)
Back Light Compensation (BLC)
Dynamic Range Compressor (DRC) Reveals Low Light Detail
Auto White Balance (AWB)
IP67 Certified (Weather Resistant)

Set Screw
5
PARTS & DESCRIPTION*
CAUTION
Lens
Bottom Case
Gimbal
OSD Joystick
Cable
Dome Cover
2nd Video Output

6
DIMENSIONS IN MILLIMETERS (IN)*
32.5
60.7
105.0

7
INSIDE THE BOX*
Included with Bullet Camera:
X
Y
Z
[
\
User Manual
Mounting Template
2 Machine Screws and 2 Dry Wall Anchors
Mounting Bolt & Nut
L-Wrench
07232013
ABOUT MANUAL
Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for future reference.
ANALOG HIGH DEFINITION
Mini Outdoor Dome Camera
DWC-V7753WTIR

8
INSTALLATION INSTRUCTIONS*
Template Sheet
1. Detach the camera’s cover dome from the
camera’s module by unscrewing the three cover
dome screws using the L-Wrench.
2. Use the camera or mounting template to mark
and drill the necessary holes in the wall or
ceiling.
3. Pull wires through and make connections.
4. Using three (3) included screws, mount and
secure the camera to the wall or ceiling.
5. Secure the camera’s cover dome onto the
camera base and remove the protecting film to
complete the installation.

9
INSTALLATION USING MOUNT BOLT & NUT*
Template Sheet
1. Detach the camera’s cover dome from the
camera’s module by unscrewing the three cover
dome screws.
2. Using the camera or mounting template, mark
and drill the necessary holes in the wall or ceiling.
3. Secure the two long mounting screws to the
camera’s base.
4. Pull wires through and make connections.
5. Mount the camera to the mounting surface
using the 2 mounting nuts.
6. Secure the camera’s cover dome onto the
camera base to complete the installation.

Use the diagram below to connect to an AHD DVR or CRT Monitor properly.
12VDC
Monitor
Second Video Output
Power Connection - 12VDC Voltage.
All cameras are equipped with a second video output for on-site configuration.
10
CONNECTING TO MONITORS*
AHD DVR