DW DWC-LPR650 User manual

Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for future reference.
ABOUT MANUAL
User Manual
DWC-LPR650
Bullet Camera
12232010
5436 W Crenshaw St. Tampa, FL 33634
Tel: [phone]
Fax: [phone]
www.Digital-Watchdog.com
[email protected]
Technical Support Hours: Monday-Friday
8:30am to 8:00pm Eastern Time

GGDo not open or modify.
GGDo not open the case except during maintenance and installation,
for it may be dangerous and can cause damages.
GDo not put objects into the unit.
GGGG
Keep metal objects ble substances from entering the camera. It can cause short-
circuits, or other damages.
GGGBe careful when handling the unit.
To prevent damages, do not drop the camera or subject it to shock or vibration.
Do not install near electric or magnetic elds.
Protect from humidity and dust.
Protect from high temperature.

Be careful when installing near the ceiling of a kitchen or a boiler room, as the temperature may
rise to high levels.
Cleaning
To remove dirt from the case, moisten a soft cloth with a soft detergent solution and wipe.
Mounting Surface
The material of the mounting surface must be strong enough to support the camera. GGGGGGGGGGGGGGGGGGGGGGGGGGGG
PRECAUTIONS
Before sending your camera for repair, check the following or contact our technical specialist.
No VIDEO
Check the coaxial cable and make sure it is connected securely.
Check the lens’ iris adjustment at the menu setup of the camera.
Check the power supply and make sure the camera has the proper voltage and current.
Out-of-Focus VIDEO
Check the clear dome cover and the lens for dirt or ngerprints. Use a soft cloth and gently clean.
Check the lens manual focal and zoom adjustment. Field test monitor is recommended.
TROUBSHOOTING
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to Provide reasonable protection
against harmful interference .when the equipment is operated in a residential environment.
This equipment generates, uses, and radiates radio frequency energy; and if it is not installed
and used in accordance with the instruction manual, it may cause harmful interference to radio
communications.
WARNING :Changes o not expressly approved by the manufacture.
FCC COMPLIANCE
3
2
1/3” Sony Super HAD II CCD
High Resolution 600 TV Lines
6~50mm Varifocal Auto Iris Lens
13~30ft Capture Range
Plate Recognition Technology Captures License Plates up to 50mph
Reliable Performance under Any Lighting Conditions
Star-Light (Super Low Light Technology)
3D-DNR (3D Digital Noise Reduction)
HME (Highlight Masking Exposure)
Easy Icon Driven OSD Menu with Built-In Joystick
Auto Sensing 12 VDC / 24 VAC with Line Lock
Secondary Video BNC Output Cable for Field Test Monitor
No Fog or Condensation under Any Weather Condition
FEATU RES*

ྺ4.2 ྺ96.7
ྺ78.0
68.0
68.0
5
4
DC12V / AC24V
Front View Bracket Rear View
230.0
86.5
122.0 96.5
BLACK
RED
(OPTION)
CABLE LENGTH
STANDARD : 13.78 (350.0mm)
5mm TWIST SORDERING
AC 24V or DC 12V
BNC JACK
VIDEO(yellow)
CONNECTION* DIMENSIONSIN MILLIMETERS*
300.0
CAUTION : CHECK THE POLARITY WHEN USING A DC12V OR AC24V POWER SUPPLY.

7
6
EXTERNAL CONTROL BOARD* CAMERA SETTING ANGLE*
LEFT
UP
DOWN
RIGHT
CON1
2nd Video Out
VR
IR LED Brightness
Adjustable
SW
OSD Control
ATTENTION
1. Do not rotate more than 360°.
2. Do not unnecessarily twist many times.
FUNCTIONAL OF CONTROL BOARD
1. SW: Functional Control OSD (On-Screen Display
2. CON1: Second Video Output Connector
3. VR: IR LED Brightness Adjustable
122.0
86.5
106.0
360˚
360˚
90˚
ྙ
ྙ
ྚ

9
8
INSTALLATION & REQUIREMENT*LENSZOOM & FOCUSADJUSTMENT*
1. Rotate Zoom lever to display desired view.
2. Rotate Focus lever to adjust the focus.
Maximum Wire Distance
Wire Gauge 12VDC 24VAC
24 AWG 80feet 323feet
22 AWG 128feet 513feet
20 AWG 203feet 815feet
18 AWG 323feet 1295feet
16 AWG 514feet 2056feet
14 AWG 816feet 3264feet
12 AWG 1295feet 5183feet
10 AWG 2057feet 8228feet
Bottom View
FOCUSZOOM
Coaxial Cable Type Maximum Distance
RG59/U 750feet
RG6/U 1,000feet
RG11/U 1,500feet
Power Requirement
12VDC !1A
24VAC !500mA

11
10
EXPOSURE
LENS DC (0~100) / MANUAL / VIDEO. (DC Lens is recommended.)
SHUTTER
1/60 / FLK / 1/250 ~ 100000 / SENS-UP x2 ~ x250
FLK (Flickerless);1/1000sec ~ 1/2000sec is recommended for License
Plate Application only.
BLC/HME OFF / BLC / HME
HME is recommended only for License Plate Application.
AGC HIGH / MIDDLE / LOW / OFF
STARIGHT AUTO (x2 ~ x250) / OFF
Not Necessary. Off is recommended for License Plate Application.
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
COLOR
WB MODE AWC / ATW / INDOOR / OUTDOOR / PUSH LOCK / MANUAL
Not Necessary for License Plate Application.
R-Y GAIN 0 ~ 100
B-Y GAIN 0 ~ 100
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
DAY & NIGHT
D&N MODE
BW
B&W Mode: BURST - OFF/ON
Less noise when the BURST is OFF.
C-SUP Color Suppression : 0 ~ 63
Not Available when 3D-DNR is ON.
A-SUP Aperture Suppression: 0 ~ 100
Not Available when 3D-DNR is ON.
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
FUNCTION
MIRROR OFF/MIRROR/V-FLIP/ROTATE
SHARPNESS 0 ~ 31
GAMMA 0.05 ~ 1.00
1.00 is recommended for License Plate Application.
FREEZE OFF / ON
Not Necessary. Off is recommended for License Plate Application.
NEGATIVE OFF/ ON
Not Necessary. Off is recommended for License Plate Application.
D-ZOOM OFF / ON (x1.0 ~ x32 PTZ)
Not Necessary. Off is recommended for License Plate Application.
3D-DNR ON (0 ~ 100) / OFF (3D Digital Noise Reduction)
Not Necessary. Off is recommended for License Plate Application.
DRC OFF / INDOOR / OUTDOOR
Not Necessary. Off is recommended for License Plate Application.
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
MOTION (Omni-Focus Lens Only)
MOTION
OFF / ON
AREA SELECT / AREA DISPLAY: OFF / O
LEFT-RIGHT / WIDTH / UP-DOWN
HEIGHT / SENSITIVITY / MOTION VIEW: ON / OFF
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET

13
12
Digital Watchdog (referred to as “the Warrantor”)
warrants the Camera Series against defects in
materials or workmanship as follows.
LABOR :For the initial two (2) years from the date of original purchase,
if the camera is determined to be defective,
the Warrantor will repair or replace the unit, with new or refurbished
product at its option, at no charge.
PARTS :In addition, the Warrantor will supply
replacement parts for the initial two (2) years.
To obtain warranty or out of warranty service,
please contact a Technical Support Representative at
1-866-446-3595 Monday through Friday from 9:00 AM to 5:00 PM Eastern.
A purchase receipt or other proof of the original purchase date is required
before warranty service is rendered. This warranty only covers failures due to
defects in materials and workmanship which arise during normal use.
This warranty does not cover damage which occurs in shipment or failures
which are caused by products not supplied by the Warrantor or failures
which result from accident, misuse, abuse, neglect, mishandling,
misapplication, alteration, modification, faulty installation, set-up adjustments,
improper antenna, inadequate signal pickup, maladjustment of consumer controls,
improper operation, power line surge, improper voltage supply, lightning damage,
rental use of the product or service by anyone other than an authorized repair
facility or damage that is attributable to acts of God.
PRIVACY
PRIVACY
OFF / ON
AREA SELECT: 1~7 / AREA DISPLAY: OFF / ON
LEFT / RIGHT / WIDTH / UP / DOWN
HEIGHT / SENSITIVITY / COLOR
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
SYNC
SYNC INTERNAL / LINE
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
SETUP
TITLE EDIT OFF / ON
PC CONTROL
(RS485 Control) CAM ID / ID DISPLAY: OFF/ON / BAUDRATE: 2400/4800/9600
LANGUAGE ENGLISH
OMNI LENS OFF/ 1~7 to enable the auto zoom function of the OMNI-PLUS
CAMERA ONLY
MONITOR CRT / LCD
Select LCD only if the camera is directly connected to an LCDMonitor.
SETUP NORMAL / HIGH
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
EXIT
EXIT
SAVE & EXIT
FACTORY RESET
WARRANTY INFORMATION*

15
14
There are no express warranties except as listed above.
The Warrantor will not be liable for incidental or consequential
damages (including, without limitation, damage to recording media)
resulting from the use of these products, or arising out of any breach
of the warranty. All express and implied warranties, including the
are limited to the applicable warranty period set forth above.
Some states do not allow the exclusion or limitation of incidental
or consequential damages, or limitations on how long an implied
warranty lasts, so the above exclusions or limitations may not
may also have other rights that vary from state to state.
If the problem is not handled to your satisfaction,
then write to the Address listed on the next page.
Service calls which do not involve defective materials or
workmanship as determined by the Warrantor, in its sole
discretion, are not covered. Costs of such service calls are
the responsibility of the purchaser.
LIMITS AND EXCLUSIONS*SPECIFICATIONS*
Model DWC-LPR650
Camera TYPE BW
License Plate Recognition Camera
Mount 3D Bracket
Image Device 1/3” Sony Super HAD II CCD
Pixels-Total 811 (H) x 508 (V)
768 (H) x 494 (V)
Scanning System 525 line, 2:1Interlace
Horizontal Frequency Internal Mode 15,734Hz
Vertical Frequency Internal Mode 59.94Hz
Min. Scene Illumination IR-LED on 0.0 Lux
IR DISTANCE 42 IR LEDs / 850nm Zero Lux
OSD Controls BLC ON/OFF (Area Setting)
AGC ON/OFF (Gain Adjust)
Shutter Speed Adjustable
HME ON/OFF
DRC OFF / INDOOR / OUTDOOR
3D-DNR OFF / On 0 ~ 100
Lens Focal Length 6 ~ 50mm Varifocal Auto Iris Lens
Resolution Horizontal 600 TV Lines
Video Output VBS 1.0Vp-p VBS 1.0Vp-p(75 Load)
S/N Ratio S/N Ratio 52dB
Environmental Conditions Operating Temperature -10o~ +55o(14o~ 131o)
Humidity Less than 90%
Power Power Requirement 12VDC / 24VAC
Power Consumption 165mA / 360mA; 4.90Watts / 4.96Watts
Dimensions(H x L) 85.4 x 231.5mm; 3.36 x 9.11in
Nema Type IP66
Weight 2.2 lbs
CE, FCC, RoHS