Dymo LabelManager 450D User manual

Follow these steps to install your LabelManager 450D label maker and print your first label.
1. Unpacking your Label Maker
x Do not connect the label maker into your computer until asked to do so during the software installation.
1Unpack your label maker and save the packing materials.
2Make sure you have all the items shown in Figure 1.
2. Connecting the Power
The label maker can operate on AC or battery power.
To connect the power adapter
1Plug the power adapter into the power connector on the top, left side
of the label maker.
2Plug the other end of the power adapter into a power outlet.
To insert the batteries
1Remove the battery compartment cover. See Figure 2.
2Insert the batteries following the polarity markings (+ and –).
3Replace the battery compartment cover.
1,2...n
Enter
P
O
L
K
I
U
J
H
G
B
V
F
T
C
D
R
E
S
X
0
987
65
4
3
2
1?
w
w
w
.
d
y
m
o
.
c
o
m
!
N
Clear
Cancel
CAPS
SPACE
&
–+
,=
/,
Y
Shift Shift
Language
Settings
Memory
Insert
Preview Symbols
Figure 1
Warranty booklet
LabelManager 450D label maker
CD-ROM
D1 tape cassette
Quick Start Guide
USB cable
User Guide
Power adapter
Figure 2
Quick Start

3. Inserting the Tape Cassette
Your label maker comes with one label cassette. You can purchase
additional tape cassettes from your local office supply retailer.
To insert the tape cassette
1Press and release the tape cassette cover to open the tape
compartment. See Figure 3.
x The first time you use the label maker, remove the protective
cardboard insert from the tape exit slot. See Figure 4.
2Make sure the tape and ribbon are taut across the mouth of the cassette
and that the tape passes between the guideposts. If necessary, turn the
spool clockwise to tighten the ribbon.
3Insert the cassette and press firmly until the cassette clicks into place. See
Figure 5 and Figure 6.
4Close the tape cassette cover and press Ato turn on the power.
You are now ready to print your first label. For complete details on how to
use the label maker refer to the LabelManager 450D User Guide.
4. Installing the Software
x Do not connect the label maker to your computer until asked to do so
during the software installation.
To install the software on a Windows system
1Insert the DYMO Label Software CD into your CD-ROM drive. After a few
seconds, the installation screen appears. If the screen does not appear:
a. Click Start and then Run on the Windows taskbar. The Run dialog
box appears.
b. Enter D:\install.exe (where D is the letter of the CD-ROM drive)
and click OK.
2Select the language to install and follow the on-screen instructions.
To install the software on a Mac OS system
1Insert the DYMO Label Software CD into the CD-ROM drive.
After a few seconds, the DYMO Label Software Installer icon appears.
2Double-click the Installer icon and follow the instructions. See Figure 7.
If you do not see the label maker in the printer list when the installation is
complete, refer to the ReadMe file for instructions on how to add the label maker.
Figure 3
Remove
cardboard
insert
Figure 4
Figure 5
Click!
Figure 6
Figure 7

Produced by:
DYMO
Stamford CT 06902
800-426-7827: www.dymo.com
5. Connecting the Label Maker to your Computer
The label maker connects to your computer using the USB connection located on the top of the label maker.
x Do not connect the label maker to your computer until asked to do so during the software installation.
To connect the label maker to your computer
1Plug the USB cable into the USB port on the top of the label maker.
See Figure 8.
2When prompted by the software installer, plug the USB cable into a USB
port on your computer.
6. Printing Labels with DYMO Label Software
The following figure shows some of the many features available in DYMO Label Software.
For complete details on how to use the software, refer to the DYMO Label Software User Guide, located on
the DYMO Label Software CD-ROM, and the online Help.
Figure 8
Insert a picture, barcode,
date, or symbol.
Insert text you’ve copied
to the Clipboard.
Store your favorite
addresses in the Address
Book and automatically
insert them on your label.
If you also have a
LabelWriter printer, two
buttons allow you to easily
switch between the label
editor and tape editor.

To print your first label
1Start DYMO Label Software as follows:
•For Windows, click Start, then Programs>DYMO Label>DYMO Label.
•For Mac OS, double-click the DYMO Label icon in the folder where you installed the software.
The first time you open the application, you are asked to register. Follow the on-screen instructions.
2If you already have a LabelWriter printer installed, click to display the Tape Editor. Otherwise,
go to step 3.
3Type some text on the label.
4Choose a font and a style setting from the Formatting toolbar.
5Click to print the label.
6Use the cutter lever to cut the label.
Printing Multiple Labels from Other Applications
With DYMO Label Software, you can quickly print multiple labels from text
created in Microsoft® Word and Excel using Smart Paste. You can use Smart
Paste to print from the clipboard or a file.
To print multiple labels quickly from Microsoft Excel
1From Excel, copy a list of items to the clipboard.
2From DYMO Label Software, clickEdit>Smart Paste>From Clipboard.
Each item is automatically printed with cut-marks between each label.
3Use the cutter lever to cut the tape and use scissors to cut each label at the cut marks.
Congratulations! You are now ready to design and print labels.
Ordering Labels
Tape cassettes are available in a wide variety of sizes and styles. You can purchase tape cassettes from your
local office supply retailer or directly from DYMO. Visit www.dymo.com.
Copy to
clipboard
Pens Pencils Erasers Paper Ink
Produced by:
DYMO
Stamford CT 06902
800-426-7827: www.dymo.com
© 2007. Sanford, L.P. 931765 Rev. 10/07