Dynamite Passport UltraDuo DYN4300 User manual

A.
L.
J.
K.
B. C. I. D. F.E.H. G.
NOTICE
All instructions, warranties and other collateral documents are subject to change
at the sole discretion of Horizon Hobby, Inc.For up-to-date product literature, visit
horizonhobby.com and click on the support tab for this product.
Meaning of Special Language
The following terms are used throughout the product literature to indicate various
levels of potential harm when operating this product:
NOTICE: Procedures, which if not properly followed, create a possibility of physical
property damage AND a little or no possibility of injury.
CAUTION: Procedures, which if not properly followed, create the probability of
physical property damage AND a possibility of serious injury.
WARNING: Procedures, which if not properly followed, create the probability of
property damage, collateral damage, and serious injury OR create a high probability
of superficial injury.
WARNING: Read the ENTIRE instruction manual to become familiar with the
features of the product before operating. Failure to operate the product
correctly can result in damage to the product, personal property and cause
serious injury.
This is a sophisticated hobby product. It must be operated with caution and common
sense and requires some basic mechanical ability. Failure to operate this Product
in a safe and responsible manner could result in injury or damage to the product or
other property.This product is not intended for use by children without direct adult
supervision. Do not attempt disassembly,use with incompatible components or
augment product in any way without the approval of Horizon Hobby, Inc.This manual
contains instructions for safety, operation and maintenance.It is essential to read
and follow all the instructions and warnings in the manual, prior to assembly,setup
or use, in order to operate correctly and avoid damage or serious injury.
Age Recommendation: Not for children under 14 years. This is not a toy.
SAFETY PRECAUTIONS AND WARNINGS
WARNING: Failure to exercise caution while using this product and comply
with the following warnings could result in product malfunction, electrical
issues, excessive heat, FIRE,and ultimately injury and property damage.
• Neverleavethepowersupply,chargerandbatteryunattendedduringuse.
• Neverattempttochargedead,damagedorwetbatterypacks.
• Neverattempttochargeabatterypackcontainingdifferenttypesofbatteries.
• Neverallowchildrenunder14yearsofagetochargebatterypacks.
• Neverchargebatteriesinextremelyhotorcoldplacesorplaceindirectsunlight.
• Neverchargeabatteryifthecablehasbeenpinchedorshorted.
• Neverconnectthechargerifthepowercablehasbeenpinchedorshorted.
• Neverconnectthechargertoanautomobile12Vbatterywhilethevehicle
is running.
• Neverattempttodismantlethechargeroruseadamagedcharger.
• NeverattachyourchargertobothanACandaDCpowersourceatthesametime.
• Neverconnecttheinputjack(DCinput)toACpower.
• Alwaysuseonlyrechargeablebatteriesdesignedforusewiththistypeofcharger.
• Alwaysinspectthebatterybeforecharging.
• Alwayskeepthebatteryawayfromanymaterialthatcouldbeaffectedbyheat.
• Alwaysmonitorthechargingareaandhaveareextinguisheravailableatalltimes.
• Alwaysendthechargingprocessifthebatterybecomeshottothetouchorstarts
tochangeform(swell)duringthechargeprocess.
• Alwaysconnectthechargecabletothechargerrst,thenconnectthebatteryto
avoid short circuit between the charge leads. Reverse the sequence when
disconnecting.
• Alwaysconnectthepositiveredleads(+)andnegativeblackleads(–)correctly.
• Alwaysdisconnectthebatteryaftercharging,andletthechargercoolbetween
charges.
• Alwayschargeinawell-ventilatedarea.
• AlwaysterminateallprocessesandcontactHorizonHobbyiftheproduct
malfunctions.
WARNING: Never leave charger unattended, exceed maximum charge rate,
charge with non-approved batteries or charge batteries in the wrong mode.
Failure to comply may result in excessive heat, fire and serious injury.
CAUTION: Always ensure the battery you are charging meets the
specifications of this charger and that the charger settings are correct. Not
doing so can result in excessive heat and other related product malfunctions,
which can lead to user injury or property damage. Please contact Horizon
Hobby or an authorized retailer with compatibility questions.
InstructIon Manual |BedIenungsanleItung |Manuel d’utIlIsatIon |Manuale dI IstruzIonI (dYn4300)
Included Items
JST_XHBalanceadapter(2)
BananaplugtoEC3™batteryconnector(2)
ACpowercord(oneregion-US,EU,AUorUK)
OPTIONAL ACCESSORIES
DYN4012-DCPowerCord
DYN5031-InsulatedChargeAdapter,BananatoEC3Device
DYN5032-BalancingAdapterBoard
DYN5033-TemperatureSensor:DYN4103,DYN4300
Minimum computer requirements for use of included software: Microsoft®
Windows XP®, Windows 7®orWindowsVista®operatingsystem,Compactdisk
(CD)readercapableofreadingamini-CDandUSB2.0port.
FEATURES
• Twochargingportstochargetwobatteriesatonce.Batteriescanbedifferent
different chemistries, capacities and cell counts
• 1AUSBchargeportcompatiblewithiPhone®, iPod®or similar products
• 100–240VAC(50/60Hz)or11–18VDCinputvoltage
• Li-Ion/Li-Po/Li-Febatterycellcountof1to6seriescells
• Ni-Cd/Ni-MHbatterycellcountof1to15cells
• Pbbatteryvoltageof2to24V
• Built-in50Wdischarger
• Built-inbalancecircuit
• Short-circuit,over-current,reversepolarity,lowinputvoltageand
over-temperature protection
• StorageandFastChargemodes
• Userbatterydata,storeandloadupto10batteryproles
• (2)2x16backlit,blueLCD
• Insulated,colorcoded,bananajack,poweroutputterminals(Red=Positive(+),
Black=CommonorNegative(–))
• Internalcoolingfanswithgrillcovers
• Operatingtemperaturerangeof0°Cto+50°C
• MeetsIP33CW,IK07environmentalspecs
• Ruggedindustrialplasticcase
SPECIFICATIONS
ACInputVoltage 100–240VAC(50/60Hz)
DCInputVoltage 11–18VDC
ChargeCurrent 0.10to10.0Aperchannel(in0.1Aincrements/200W
maximumperchannel/400WTotal)
DischargeCurrent 0.10to5.0Aperchannel(in0.1Aincrements/50W
maximumperchannel/100WTotal)
Operating Temperature 0°Cto+50°C
BalanceCurrentDrain 300mApercell
TrickleChargeCurrent 50to200mA
ChargingMode Peak(Ni-Cd/Ni-MH),CC/CV(Li-Po/Li-Ion/Li-Fe/Pb)
GETTING STARTED
CAUTION:NeverconnecttheACandDCinputcordstoanactivepower
source at the same time. This will void the warranty, cause product
damage and possibly injure the user.
When Using an External DC Power Source:
1.ConnecttheDCpowercordtothechargerDCpowerinputport.
2.ConnecttheDCalligatorclipstotheDCpowersource.
3.PowerONthechargerwiththepowerswitch.
4.WhenthechargerispoweredON,amessagewillappearontheLCDscreen.
NOTICE: Always connect cable polarities correctly.
NOTICE: Alwaysconsult12VbatterycollateralmaterialsorHorizonHobby
beforeusingwithsourcesotherthanastandardACwalloutlet.
When Using an External AC Power Source:
1.ConnecttheACpowercordtothechargerACpowerinputport.
2.ConnecttheACpowercordtotheACpowersource.
3.PowerONthechargerwiththepowerswitch.
4.WhenthechargerispoweredON,amessagewillappearontheLCDscreen.
CAUTION: Always power ON the charger before connecting a battery, or
damage to the charger and the battery can result.
1.Connectthechargertothepowersource.
2.PowerONthecharger.
3.Makeprogramselectionsinthechargerforbatterycharging.
4.Connectthechargeradapterstothecharger.
5.Connectthebatterytothechargeradapters(connectmaincharging
connectorsbeforeconnectingcell-balancingconnectors,whereused).
6.Startbatterycharging.
A. PowerOutputRed(+)
B. PowerOutputBlack(–)
C. BalanceCircuitAdapter
BoardConnector
D. TemperatureProbeConnection
E. Mode/StopKey
F. USBCommunicationsPort
G. 1AUSBChargePort
H. Jog Dial
I. LCDScreen
J. ACPowerInputPort
K. Power Switch
L. DCPowerInput/
APPConnectors
PROGRAM SELECT
LiFe BATT
LiFe BALANCE
2.0A 19.8V(6S)
LiFe CHARGE
2.0A 19.8V(6S)
LiFe DISCHARGE
2.0A 19.8V(6S)
LiFe FAST CHG
2.0A 19.8V(6S)
LiFe STORAGE
2.0A 19.8V(6S)
PROGRAM SELECT
LiIo BATT
LiIo FAST CHG
2.0A 21.6V(6S)
LiIo BALANCE
2.0A 21.6V(6S)
LiIo CHARGE
2.0A 21.6V(6S)
LiIo STORAGE
2.0A 21.6V(6S)
LiIo DISCHARGE
2.0A 21.6V(6S)
PROGRAM SELECT
LiPo BATT
LiPo FAST CHG
2.0A 22.2V(6S)
LiPo BALANCE
2.0A 22.2V(6S)
LiPo CHARGE
2.0A 22.2V(6S)
LiPo STORAGE
2.0A 22.2V(6S)
LiPo DISCHARGE
2.0A 22.2V(6S)
PROGRAM SELECT
Pb BATT
Pb CHARGE
2.0A 2.0V (1P)
Pb DISCHARGE
2.0A 2.0V (1P)
PROGRAM SELECT
NiMH BATT
NiMH DISCHARGE
0.1A CUT:1.0V
NiMH CHARGE
CURRENT 2.0A
NiMH Auto CHARGE
CURRENT 2.0A
NiMH RE-PEAK
2
NiMH CYCLE
DCHG>CHG 1
PROGRAM SELECT
NiCd BATT
NiCd CHARGE
CURRENT 2.0A
NiCd DISCHARGE
0.1A CUT: 1.0V
NiCd RE-PEAK
2
NiCd CYCLE
DCHG>CHG 1
NiCd Auto CHARGE
CURRENT 2.0A
PROGRAM SELECT
LI BATT METER
0.00 0.00 0.00 V
0.00 0.00 0.00 V
MAIN 00.00V
H0.000V L0.000V
PROGRAM SELECT
BATT MEMORY
[BATT MEMORY 1]
ENTER SET ->
BATT TYPE
LiPo
TVC=YOUR RISK!
4.20V
DSCH VOLTAGE
3.0V/CELL
DSCH CURRENT
1.0A
CHARGE CURRENT
2.2A
BATT VOLTS
7.4V(2S)
SAVE PROGRAM
ENTER
TEMPERATURE
CUT-OFF 50C
PROGRAM SELECT
SYSTEM SET->
LOAD FACTORY SET
ENTER
Rest Time
CHG>DCHG 10min
VERSION
1.00
Key Beep ON
Buzzer ON
Ext. Temp 0C
Int. Temp 32C
Input Power Low
Cut-Off 11.0V
Capacity Cut-Off
ON 5000mAh
SAFETY TIMER
ON 120min
PROGRAM SELECT
LiFe BATT
LiFe BALANCE
2.0A 19.8V(6S)
LiFe CHARGE
2.0A 19.8V(6S)
LiFe DISCHARGE
2.0A 19.8V(6S)
LiFe FAST CHG
2.0A 19.8V(6S)
LiFe STORAGE
2.0A 19.8V(6S)
PROGRAM SELECT
LiIo BATT
LiIo FAST CHG
2.0A 21.6V(6S)
LiIo BALANCE
2.0A 21.6V(6S)
LiIo CHARGE
2.0A 21.6V(6S)
LiIo STORAGE
2.0A 21.6V(6S)
LiIo DISCHARGE
2.0A 21.6V(6S)
PROGRAM SELECT
LiPo BATT
LiPo FAST CHG
2.0A 22.2V(6S)
LiPo BALANCE
2.0A 22.2V(6S)
LiPo CHARGE
2.0A 22.2V(6S)
LiPo STORAGE
2.0A 22.2V(6S)
LiPo DISCHARGE
2.0A 22.2V(6S)
PROGRAM SELECT
Pb BATT
Pb CHARGE
2.0A 2.0V (1P)
Pb DISCHARGE
2.0A 2.0V (1P)
PROGRAM SELECT
NiMH BATT
NiMH DISCHARGE
0.1A CUT:1.0V
NiMH CHARGE
CURRENT 2.0A
NiMH Auto CHARGE
CURRENT 2.0A
NiMH RE-PEAK
2
NiMH CYCLE
DCHG>CHG 1
PROGRAM SELECT
NiCd BATT
NiCd CHARGE
CURRENT 2.0A
NiCd DISCHARGE
0.1A CUT: 1.0V
NiCd RE-PEAK
2
NiCd CYCLE
DCHG>CHG 1
NiCd Auto CHARGE
CURRENT 2.0A
PROGRAM SELECT
LI BATT METER
0.00 0.00 0.00 V
0.00 0.00 0.00 V
MAIN 00.00V
H0.000V L0.000V
PROGRAM SELECT
BATT MEMORY
[BATT MEMORY 1]
ENTER SET ->
BATT TYPE
LiPo
TVC=YOUR RISK!
4.20V
DSCH VOLTAGE
3.0V/CELL
DSCH CURRENT
1.0A
CHARGE CURRENT
2.2A
BATT VOLTS
7.4V(2S)
SAVE PROGRAM
ENTER
TEMPERATURE
CUT-OFF 50C
PROGRAM SELECT
SYSTEM SET->
LOAD FACTORY SET
ENTER
Rest Time
CHG>DCHG 10min
VERSION
1.00
Key Beep ON
Buzzer ON
Ext. Temp 0C
Int. Temp 32C
Input Power Low
Cut-Off 11.0V
Capacity Cut-Off
ON 5000mAh
SAFETY TIMER
ON 120min
PROGRAM SELECT
LiFe BATT
LiFe BALANCE
2.0A 19.8V(6S)
LiFe CHARGE
2.0A 19.8V(6S)
LiFe DISCHARGE
2.0A 19.8V(6S)
LiFe FAST CHG
2.0A 19.8V(6S)
LiFe STORAGE
2.0A 19.8V(6S)
PROGRAM SELECT
LiIo BATT
LiIo FAST CHG
2.0A 21.6V(6S)
LiIo BALANCE
2.0A 21.6V(6S)
LiIo CHARGE
2.0A 21.6V(6S)
LiIo STORAGE
2.0A 21.6V(6S)
LiIo DISCHARGE
2.0A 21.6V(6S)
PROGRAM SELECT
LiPo BATT
LiPo FAST CHG
2.0A 22.2V(6S)
LiPo BALANCE
2.0A 22.2V(6S)
LiPo CHARGE
2.0A 22.2V(6S)
LiPo STORAGE
2.0A 22.2V(6S)
LiPo DISCHARGE
2.0A 22.2V(6S)
PROGRAM SELECT
Pb BATT
Pb CHARGE
2.0A 2.0V (1P)
Pb DISCHARGE
2.0A 2.0V (1P)
PROGRAM SELECT
NiMH BATT
NiMH DISCHARGE
0.1A CUT:1.0V
NiMH CHARGE
CURRENT 2.0A
NiMH Auto CHARGE
CURRENT 2.0A
NiMH RE-PEAK
2
NiMH CYCLE
DCHG>CHG 1
PROGRAM SELECT
NiCd BATT
NiCd CHARGE
CURRENT 2.0A
NiCd DISCHARGE
0.1A CUT: 1.0V
NiCd RE-PEAK
2
NiCd CYCLE
DCHG>CHG 1
NiCd Auto CHARGE
CURRENT 2.0A
PROGRAM SELECT
LI BATT METER
0.00 0.00 0.00 V
0.00 0.00 0.00 V
MAIN 00.00V
H0.000V L0.000V
PROGRAM SELECT
BATT MEMORY
[BATT MEMORY 1]
ENTER SET ->
BATT TYPE
LiPo
TVC=YOUR RISK!
4.20V
DSCH VOLTAGE
3.0V/CELL
DSCH CURRENT
1.0A
CHARGE CURRENT
2.2A
BATT VOLTS
7.4V(2S)
SAVE PROGRAM
ENTER
TEMPERATURE
CUT-OFF 50C
PROGRAM SELECT
SYSTEM SET->
LOAD FACTORY SET
ENTER
Rest Time
CHG>DCHG 10min
VERSION
1.00
Key Beep ON
Buzzer ON
Ext. Temp 0C
Int. Temp 32C
Input Power Low
Cut-Off 11.0V
Capacity Cut-Off
ON 5000mAh
SAFETY TIMER
ON 120min
PROGRAM SELECT
LiFe BATT
LiFe BALANCE
2.0A 19.8V(6S)
LiFe CHARGE
2.0A 19.8V(6S)
LiFe DISCHARGE
2.0A 19.8V(6S)
LiFe FAST CHG
2.0A 19.8V(6S)
LiFe STORAGE
2.0A 19.8V(6S)
PROGRAM SELECT
LiIo BATT
LiIo FAST CHG
2.0A 21.6V(6S)
LiIo BALANCE
2.0A 21.6V(6S)
LiIo CHARGE
2.0A 21.6V(6S)
LiIo STORAGE
2.0A 21.6V(6S)
LiIo DISCHARGE
2.0A 21.6V(6S)
PROGRAM SELECT
LiPo BATT
LiPo FAST CHG
2.0A 22.2V(6S)
LiPo BALANCE
2.0A 22.2V(6S)
LiPo CHARGE
2.0A 22.2V(6S)
LiPo STORAGE
2.0A 22.2V(6S)
LiPo DISCHARGE
2.0A 22.2V(6S)
PROGRAM SELECT
Pb BATT
Pb CHARGE
2.0A 2.0V (1P)
Pb DISCHARGE
2.0A 2.0V (1P)
PROGRAM SELECT
NiMH BATT
NiMH DISCHARGE
0.1A CUT:1.0V
NiMH CHARGE
CURRENT 2.0A
NiMH Auto CHARGE
CURRENT 2.0A
NiMH RE-PEAK
2
NiMH CYCLE
DCHG>CHG 1
PROGRAM SELECT
NiCd BATT
NiCd CHARGE
CURRENT 2.0A
NiCd DISCHARGE
0.1A CUT: 1.0V
NiCd RE-PEAK
2
NiCd CYCLE
DCHG>CHG 1
NiCd Auto CHARGE
CURRENT 2.0A
PROGRAM SELECT
LI BATT METER
0.00 0.00 0.00 V
0.00 0.00 0.00 V
MAIN 00.00V
H0.000V L0.000V
PROGRAM SELECT
BATT MEMORY
[BATT MEMORY 1]
ENTER SET ->
BATT TYPE
LiPo
TVC=YOUR RISK!
4.20V
DSCH VOLTAGE
3.0V/CELL
DSCH CURRENT
1.0A
CHARGE CURRENT
2.2A
BATT VOLTS
7.4V(2S)
SAVE PROGRAM
ENTER
TEMPERATURE
CUT-OFF 50C
PROGRAM SELECT
SYSTEM SET->
LOAD FACTORY SET
ENTER
Rest Time
CHG>DCHG 10min
VERSION
1.00
Key Beep ON
Buzzer ON
Ext. Temp 0C
Int. Temp 32C
Input Power Low
Cut-Off 11.0V
Capacity Cut-Off
ON 5000mAh
SAFETY TIMER
ON 120min
PROGRAM SELECT
LiFe BATT
LiFe BALANCE
2.0A 19.8V(6S)
LiFe CHARGE
2.0A 19.8V(6S)
LiFe DISCHARGE
2.0A 19.8V(6S)
LiFe FAST CHG
2.0A 19.8V(6S)
LiFe STORAGE
2.0A 19.8V(6S)
PROGRAM SELECT
LiIo BATT
LiIo FAST CHG
2.0A 21.6V(6S)
LiIo BALANCE
2.0A 21.6V(6S)
LiIo CHARGE
2.0A 21.6V(6S)
LiIo STORAGE
2.0A 21.6V(6S)
LiIo DISCHARGE
2.0A 21.6V(6S)
PROGRAM SELECT
LiPo BATT
LiPo FAST CHG
2.0A 22.2V(6S)
LiPo BALANCE
2.0A 22.2V(6S)
LiPo CHARGE
2.0A 22.2V(6S)
LiPo STORAGE
2.0A 22.2V(6S)
LiPo DISCHARGE
2.0A 22.2V(6S)
PROGRAM SELECT
Pb BATT
Pb CHARGE
2.0A 2.0V (1P)
Pb DISCHARGE
2.0A 2.0V (1P)
PROGRAM SELECT
NiMH BATT
NiMH DISCHARGE
0.1A CUT:1.0V
NiMH CHARGE
CURRENT 2.0A
NiMH Auto CHARGE
CURRENT 2.0A
NiMH RE-PEAK
2
NiMH CYCLE
DCHG>CHG 1
PROGRAM SELECT
NiCd BATT
NiCd CHARGE
CURRENT 2.0A
NiCd DISCHARGE
0.1A CUT: 1.0V
NiCd RE-PEAK
2
NiCd CYCLE
DCHG>CHG 1
NiCd Auto CHARGE
CURRENT 2.0A
PROGRAM SELECT
LI BATT METER
0.00 0.00 0.00 V
0.00 0.00 0.00 V
MAIN 00.00V
H0.000V L0.000V
PROGRAM SELECT
BATT MEMORY
[BATT MEMORY 1]
ENTER SET ->
BATT TYPE
LiPo
TVC=YOUR RISK!
4.20V
DSCH VOLTAGE
3.0V/CELL
DSCH CURRENT
1.0A
CHARGE CURRENT
2.2A
BATT VOLTS
7.4V(2S)
SAVE PROGRAM
ENTER
TEMPERATURE
CUT-OFF 50C
PROGRAM SELECT
SYSTEM SET->
LOAD FACTORY SET
ENTER
Rest Time
CHG>DCHG 10min
VERSION
1.00
Key Beep ON
Buzzer ON
Ext. Temp 0C
Int. Temp 32C
Input Power Low
Cut-Off 11.0V
Capacity Cut-Off
ON 5000mAh
SAFETY TIMER
ON 120min
PROGRAM SELECT
LiFe BATT
LiFe BALANCE
2.0A 19.8V(6S)
LiFe CHARGE
2.0A 19.8V(6S)
LiFe DISCHARGE
2.0A 19.8V(6S)
LiFe FAST CHG
2.0A 19.8V(6S)
LiFe STORAGE
2.0A 19.8V(6S)
PROGRAM SELECT
LiIo BATT
LiIo FAST CHG
2.0A 21.6V(6S)
LiIo BALANCE
2.0A 21.6V(6S)
LiIo CHARGE
2.0A 21.6V(6S)
LiIo STORAGE
2.0A 21.6V(6S)
LiIo DISCHARGE
2.0A 21.6V(6S)
PROGRAM SELECT
LiPo BATT
LiPo FAST CHG
2.0A 22.2V(6S)
LiPo BALANCE
2.0A 22.2V(6S)
LiPo CHARGE
2.0A 22.2V(6S)
LiPo STORAGE
2.0A 22.2V(6S)
LiPo DISCHARGE
2.0A 22.2V(6S)
PROGRAM SELECT
Pb BATT
Pb CHARGE
2.0A 2.0V (1P)
Pb DISCHARGE
2.0A 2.0V (1P)
PROGRAM SELECT
NiMH BATT
NiMH DISCHARGE
0.1A CUT:1.0V
NiMH CHARGE
CURRENT 2.0A
NiMH Auto CHARGE
CURRENT 2.0A
NiMH RE-PEAK
2
NiMH CYCLE
DCHG>CHG 1
PROGRAM SELECT
NiCd BATT
NiCd CHARGE
CURRENT 2.0A
NiCd DISCHARGE
0.1A CUT: 1.0V
NiCd RE-PEAK
2
NiCd CYCLE
DCHG>CHG 1
NiCd Auto CHARGE
CURRENT 2.0A
PROGRAM SELECT
LI BATT METER
0.00 0.00 0.00 V
0.00 0.00 0.00 V
MAIN 00.00V
H0.000V L0.000V
PROGRAM SELECT
BATT MEMORY
[BATT MEMORY 1]
ENTER SET ->
BATT TYPE
LiPo
TVC=YOUR RISK!
4.20V
DSCH VOLTAGE
3.0V/CELL
DSCH CURRENT
1.0A
CHARGE CURRENT
2.2A
BATT VOLTS
7.4V(2S)
SAVE PROGRAM
ENTER
TEMPERATURE
CUT-OFF 50C
PROGRAM SELECT
SYSTEM SET->
LOAD FACTORY SET
ENTER
Rest Time
CHG>DCHG 10min
VERSION
1.00
Key Beep ON
Buzzer ON
Ext. Temp 0C
Int. Temp 32C
Input Power Low
Cut-Off 11.0V
Capacity Cut-Off
ON 5000mAh
SAFETY TIMER
ON 120min
PROGRAM SELECT
LiFe BATT
LiFe BALANCE
2.0A 19.8V(6S)
LiFe CHARGE
2.0A 19.8V(6S)
LiFe DISCHARGE
2.0A 19.8V(6S)
LiFe FAST CHG
2.0A 19.8V(6S)
LiFe STORAGE
2.0A 19.8V(6S)
PROGRAM SELECT
LiIo BATT
LiIo FAST CHG
2.0A 21.6V(6S)
LiIo BALANCE
2.0A 21.6V(6S)
LiIo CHARGE
2.0A 21.6V(6S)
LiIo STORAGE
2.0A 21.6V(6S)
LiIo DISCHARGE
2.0A 21.6V(6S)
PROGRAM SELECT
LiPo BATT
LiPo FAST CHG
2.0A 22.2V(6S)
LiPo BALANCE
2.0A 22.2V(6S)
LiPo CHARGE
2.0A 22.2V(6S)
LiPo STORAGE
2.0A 22.2V(6S)
LiPo DISCHARGE
2.0A 22.2V(6S)
PROGRAM SELECT
Pb BATT
Pb CHARGE
2.0A 2.0V (1P)
Pb DISCHARGE
2.0A 2.0V (1P)
PROGRAM SELECT
NiMH BATT
NiMH DISCHARGE
0.1A CUT:1.0V
NiMH CHARGE
CURRENT 2.0A
NiMH Auto CHARGE
CURRENT 2.0A
NiMH RE-PEAK
2
NiMH CYCLE
DCHG>CHG 1
PROGRAM SELECT
NiCd BATT
NiCd CHARGE
CURRENT 2.0A
NiCd DISCHARGE
0.1A CUT: 1.0V
NiCd RE-PEAK
2
NiCd CYCLE
DCHG>CHG 1
NiCd Auto CHARGE
CURRENT 2.0A
PROGRAM SELECT
LI BATT METER
0.00 0.00 0.00 V
0.00 0.00 0.00 V
MAIN 00.00V
H0.000V L0.000V
PROGRAM SELECT
BATT MEMORY
[BATT MEMORY 1]
ENTER SET ->
BATT TYPE
LiPo
TVC=YOUR RISK!
4.20V
DSCH VOLTAGE
3.0V/CELL
DSCH CURRENT
1.0A
CHARGE CURRENT
2.2A
BATT VOLTS
7.4V(2S)
SAVE PROGRAM
ENTER
TEMPERATURE
CUT-OFF 50C
PROGRAM SELECT
SYSTEM SET->
LOAD FACTORY SET
ENTER
Rest Time
CHG>DCHG 10min
VERSION
1.00
Key Beep ON
Buzzer ON
Ext. Temp 0C
Int. Temp 32C
Input Power Low
Cut-Off 11.0V
Capacity Cut-Off
ON 5000mAh
SAFETY TIMER
ON 120min
PROGRAM SELECT
LiFe BATT
LiFe BALANCE
2.0A 19.8V(6S)
LiFe CHARGE
2.0A 19.8V(6S)
LiFe DISCHARGE
2.0A 19.8V(6S)
LiFe FAST CHG
2.0A 19.8V(6S)
LiFe STORAGE
2.0A 19.8V(6S)
PROGRAM SELECT
LiIo BATT
LiIo FAST CHG
2.0A 21.6V(6S)
LiIo BALANCE
2.0A 21.6V(6S)
LiIo CHARGE
2.0A 21.6V(6S)
LiIo STORAGE
2.0A 21.6V(6S)
LiIo DISCHARGE
2.0A 21.6V(6S)
PROGRAM SELECT
LiPo BATT
LiPo FAST CHG
2.0A 22.2V(6S)
LiPo BALANCE
2.0A 22.2V(6S)
LiPo CHARGE
2.0A 22.2V(6S)
LiPo STORAGE
2.0A 22.2V(6S)
LiPo DISCHARGE
2.0A 22.2V(6S)
PROGRAM SELECT
Pb BATT
Pb CHARGE
2.0A 2.0V (1P)
Pb DISCHARGE
2.0A 2.0V (1P)
PROGRAM SELECT
NiMH BATT
NiMH DISCHARGE
0.1A CUT:1.0V
NiMH CHARGE
CURRENT 2.0A
NiMH Auto CHARGE
CURRENT 2.0A
NiMH RE-PEAK
2
NiMH CYCLE
DCHG>CHG 1
PROGRAM SELECT
NiCd BATT
NiCd CHARGE
CURRENT 2.0A
NiCd DISCHARGE
0.1A CUT: 1.0V
NiCd RE-PEAK
2
NiCd CYCLE
DCHG>CHG 1
NiCd Auto CHARGE
CURRENT 2.0A
PROGRAM SELECT
LI BATT METER
0.00 0.00 0.00 V
0.00 0.00 0.00 V
MAIN 00.00V
H0.000V L0.000V
PROGRAM SELECT
BATT MEMORY
[BATT MEMORY 1]
ENTER SET ->
BATT TYPE
LiPo
TVC=YOUR RISK!
4.20V
DSCH VOLTAGE
3.0V/CELL
DSCH CURRENT
1.0A
CHARGE CURRENT
2.2A
BATT VOLTS
7.4V(2S)
SAVE PROGRAM
ENTER
TEMPERATURE
CUT-OFF 50C
PROGRAM SELECT
SYSTEM SET->
LOAD FACTORY SET
ENTER
Rest Time
CHG>DCHG 10min
VERSION
1.00
Key Beep ON
Buzzer ON
Ext. Temp 0C
Int. Temp 32C
Input Power Low
Cut-Off 11.0V
Capacity Cut-Off
ON 5000mAh
SAFETY TIMER
ON 120min
PROGRAM SELECT
LiFe BATT
LiFe BALANCE
2.0A 19.8V(6S)
LiFe CHARGE
2.0A 19.8V(6S)
LiFe DISCHARGE
2.0A 19.8V(6S)
LiFe FAST CHG
2.0A 19.8V(6S)
LiFe STORAGE
2.0A 19.8V(6S)
PROGRAM SELECT
LiIo BATT
LiIo FAST CHG
2.0A 21.6V(6S)
LiIo BALANCE
2.0A 21.6V(6S)
LiIo CHARGE
2.0A 21.6V(6S)
LiIo STORAGE
2.0A 21.6V(6S)
LiIo DISCHARGE
2.0A 21.6V(6S)
PROGRAM SELECT
LiPo BATT
LiPo FAST CHG
2.0A 22.2V(6S)
LiPo BALANCE
2.0A 22.2V(6S)
LiPo CHARGE
2.0A 22.2V(6S)
LiPo STORAGE
2.0A 22.2V(6S)
LiPo DISCHARGE
2.0A 22.2V(6S)
PROGRAM SELECT
Pb BATT
Pb CHARGE
2.0A 2.0V (1P)
Pb DISCHARGE
2.0A 2.0V (1P)
PROGRAM SELECT
NiMH BATT
NiMH DISCHARGE
0.1A CUT:1.0V
NiMH CHARGE
CURRENT 2.0A
NiMH Auto CHARGE
CURRENT 2.0A
NiMH RE-PEAK
2
NiMH CYCLE
DCHG>CHG 1
PROGRAM SELECT
NiCd BATT
NiCd CHARGE
CURRENT 2.0A
NiCd DISCHARGE
0.1A CUT: 1.0V
NiCd RE-PEAK
2
NiCd CYCLE
DCHG>CHG 1
NiCd Auto CHARGE
CURRENT 2.0A
PROGRAM SELECT
LI BATT METER
0.00 0.00 0.00 V
0.00 0.00 0.00 V
MAIN 00.00V
H0.000V L0.000V
PROGRAM SELECT
BATT MEMORY
[BATT MEMORY 1]
ENTER SET ->
BATT TYPE
LiPo
TVC=YOUR RISK!
4.20V
DSCH VOLTAGE
3.0V/CELL
DSCH CURRENT
1.0A
CHARGE CURRENT
2.2A
BATT VOLTS
7.4V(2S)
SAVE PROGRAM
ENTER
TEMPERATURE
CUT-OFF 50C
PROGRAM SELECT
SYSTEM SET->
LOAD FACTORY SET
ENTER
Rest Time
CHG>DCHG 10min
VERSION
1.00
Key Beep ON
Buzzer ON
Ext. Temp 0C
Int. Temp 32C
Input Power Low
Cut-Off 11.0V
Capacity Cut-Off
ON 5000mAh
SAFETY TIMER
ON 120min
PROGRAMMING QUICK GUIDE
Press the Mode key (G) to get to the 9 main menus from any submenu screen.
Press the Jog Dial (H) to get to the submenus for adjusting operating parameters, to save value changes or to start chosen battery charging actions.
Rotate the Jog Dial (H) to change between submenu screens or to change screen values.
JST_XH ADAPTER
2S 3S 4S 6S5S
JST_XH ADAPTER
2S 3S 4S 6S5S
Not to scale.
Not all wiring shown.
Not all connectors shown.
OPERATING YOUR CHARGER
1SELF TEST AND PROGRAM SELECT SCREENS
Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to
locatethePROGRAMSELECTLiFeBATTscreen.PresstheJog DialtoselectLiFe.
Rotate the Jog Dialtogotooneofthecontrolscreens(BALANCE,CHARGE,FAST
CHG,STORAGEorDISCHARGE)todowhatyourbatteryneeds.
Correctlyconnectyourlithiumbatterytothecharger(chargingconnectorrstand
balancingconnectorsecond).PresstheJog Dial and adjust charging parameters
as needed. Press and hold the Jog Dial(approximately3seconds)untilthescreen
changestostartthebatterycheck/chargesequence.
R: 3SER S:3SER
CONFIRM (ENTER)
AWhen the charge cycle starts, the
charger compares the battery to the
charger settings. The screen will show
the battery and your settings
information.IftheinformationafterR:(charger)andS:(settings)(A) does not match,
press the Mode key and change the lithium battery charging parameters as
needed. If the R: information matches S:,press the Jog Dial to confirm. After
conrmation,chargingstartsandinformationwillshowontheLCDscreen
(informationmayvary).
LI 3S 2.0A 12.59V
BAL 022:43 01082
F E
B C D
A
A. ALi-Febatterypackis
balance charging
B. Batterypackhas3cellsin
series
C. Chargingrateis2.0A(2000mAh)
D. Voltagebeingappliedtothebatteryiscurrently12.59V
E. Presentchargelevelofthebatteryis1082mAh
F. Timeelapsedsincethechargeprocessstartedis22:43(22minutesand43
seconds)
During charging, the Jog Dial can be rotated counterclockwise to show several
parametermessagesontheLCDscreen,including:EndVoltage,InputPowerVolt-
age,External&InternalTemperature,TemperatureCutoff,SafetyTimerStatusand
CapacityCutoff.
Rotate the Jog Dial clockwise to show the charge voltages for each cell. Press the
Jog DialatanytimetoreturntotheChargeMonitorscreen.Thechargersignals
whenthecharging(ordischarging)processiscomplete(ifBuzzerissettoON).
CAUTION:TheLi-FeprogrammenusaretobeusedONLYforthe
charginganddischargingofLi-Febatteries.Thechargingofotherbattery
types using these programs will result in damage to the battery or charger.
CAUTION:Usingachargeratethatisnotcompatiblewiththebattery
capacities may result in damage or malfunction of the charger or
batteries.
3LI-FE BALANCE CHARGING
When the charger is powered ON, there is a series of self tests and the screen will
show the charger brand name and model number.
DYNAMITE
DYN4300
After the self tests, the charger will show another screen.The information on this
screen will vary but will look similar to this:
LiPo BALANCE
2.0A 7.4V(2S)
From any screen, press the Mode key to go back to the main menu.
2LI-FE BATTERIES
Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial
tolocatethePROGRAMSELECTLiFeBATTscreen.PresstheJog Dial to go into
this menu.
Rotate the Jog DialtogototheLiFeBALANCEscreenandsetchargingparam-
eters. The charging amperage (A)canbesetbetween0.1and10.0A.Voltage(B)
isdependentonthenumberofcellsinseries.Forexample,withLi-Febatteries
thesevaluescanbefrom3.3V(for1Sbatteries)to19.8V(for6Sbatteries).
LiFe BALANCE
5.5A 19.8V(6S)
A B C
To select values other than the existing parameters:
• PresstheJog Dial so the charge current value (A) flashes
• RotatetheJog DialtoINCREASEORDECREASEthechargecurrentvalue
• PresstheJog Dial to save the value and the voltage value (B) flashes
• RotatetheJog DialtoINCREASEORDECREASEthevoltage(and#ofcellsin
series (C))
• PresstheJog Dial to save the voltage value
If no parameters are flashing, you can rotate the Jog Dial to select another
programsuchasCHARGE,FASTCHG,STORAGEorDISCHARGE.
To start charging,press and hold the Jog Dialfor3seconds.
4LI-FE CHARGING
Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial
tolocatethePROGRAMSELECTLiFeBATTscreen.PresstheJog Dial to go into
this menu.
Rotate the Jog DialtogototheLiFeCHARGEscreenandsetchargingparam-
eters. The charging amperage (A)canbesetbetween0.1and10.0A.Voltage(B)
isdependentonthenumberofcellsinseries.Forexample,withLi-Febatteries
thesevaluescanbefrom3.3V(for1Sbatteries)to19.8V(for6Sbatteries).
LiFe CHARGE
4.6A 19.8V(6S)
A B C
To select values other than the existing parameters:
• PresstheJog Dial so the charge current value (A) flashes
• RotatetheJog DialtoINCREASEORDECREASEthechargecurrentvalue
• PresstheJog Dial to save the value and the voltage value (B) flashes
• RotatetheJog DialtoINCREASEORDECREASEthevoltage(and#ofcellsin
series (C))
• PresstheJog Dial to save the voltage value
If no parameters are flashing, you can rotate the Jog Dial to select another
programsuchasBALANCE,FASTCHG,STORAGEorDISCHARGE.
To start charging,press and hold the Jog Dialfor3seconds.
CAUTION: If at any time during the charge process the battery becomes
hot or begins to puff, disconnect the battery immediately and discontinue
the charge process as batteries can cause fire, collateral damage and
injuries.
5LI-FE FAST CHARGING
Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial
tolocatethePROGRAMSELECTLiFeBATTscreen.PresstheJog Dial to go into
this menu.
Rotate the Jog DialtogototheLiFeFASTCHGscreenandsetchargingparam-
eters. The charging amperage (A)canbesetbetween0.1and10.0A.Voltage(B)
isdependentonthenumberofcellsinseries.Forexample,withLi-Febatteries
thesevaluescanbefrom3.3V(for1Sbatteries)to19.8V(for6Sbatteries).
Neartheendofastandardchargingcycle,thechargerswitchesfromConstant
Current(CC)modetoConstantVoltage(CV)modetoslowly“topoff”thecurrentin
the battery as close as possible to the maximum capacity.
InFastCharge,theCVmodeiseliminatedinordertogreatlyshortenthecharging
time; however,the final capacity of the battery will be less than what you would get
using the standard charge method.
LiFe FAST CHG
0.1A 19.8V(6S)
A B C
To select values other than the existing parameters:
• PresstheJog Dial so the charge current value (A) flashes
• RotatetheJog DialtoINCREASEORDECREASEthechargecurrentvalue
• PresstheJog Dial to save the value and the voltage value (B) flashes
• RotatetheJog DialtoINCREASEORDECREASEthevoltage(and#ofcellsin
series (C))
• PresstheJog Dial to save the voltage value
If no parameters are flashing, you can rotate the Jog Dial to select another
programsuchasCHARGE,BALANCE,STORAGEorDISCHARGE.
To start charging,press and hold the Jog Dialfor3seconds.
6LI-FE STORAGE CHARGING
Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial
tolocatethePROGRAMSELECTLiFeBATTscreen.PresstheJog Dial to go into
this menu.
Rotate the Jog DialtogototheLiFeSTORAGEscreenandsetchargingparam-
eters. The charging amperage (A)canbesetbetween0.1and10.0A.Voltage(B)
isdependentonthenumberofcellsinseries.Forexample,withLi-Febatteries
thesevaluescanbefrom3.3V(for1Sbatteries)to19.8V(for6Sbatteries).
Ifyoudon’tplanonusingyourbatteryforalongtime,itisbesttocharge(or
discharge)thebatterytoitsoptimalstoragevoltageandcapacity.
LiFe STORAGE
2.5A 19.8V(6S)
A B C
To select values other than the existing parameters:
• PresstheJog Dial so the charge current value (A) flashes
• RotatetheJog DialtoINCREASEORDECREASEthechargecurrentvalue
• PresstheJog Dial to save the value and the voltage value (B) flashes
• RotatetheJog DialtoINCREASEORDECREASEthevoltage(and#ofcellsin
series (C))
• PresstheJog Dial to save the voltage value
If no parameters are flashing, you can rotate the Jog Dial to select another
programsuchasCHARGE,BALANCE,FASTCHGorDISCHARGE.
To start charging,press and hold the Jog Dialfor3seconds.
7LI-FE DISCHARGING
Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial
tolocatethePROGRAMSELECTLiFeBATTscreen.PresstheJog Dial to go into
this menu.
Rotate the Jog DialtogototheLiFeDISCHARGEscreenandsetdischarging
parameters. The discharging amperage (A)canbesetbetween0.1and5.0A.Volt-
age (B)isdependentonthenumberofcellsinseries.Forexample,withLi-Febat-
teriesthesevaluescanbefrom3.3V(for1Sbatteries)to19.8V(for6Sbatteries).
A battery’s capacity can be verified by discharging it to its minimum voltage level
and measuring the current as the battery is discharged.
LiFe DISCHARGE
2.0A 19.8V(6S)
A B C
To select values other than the existing parameters:
• PresstheJog Dial so the discharge current value (A) flashes
• RotatetheJog DialtoINCREASEORDECREASEthedischargecurrentvalue
• PresstheJog Dial to save the value and the voltage value (B) flashes
• RotatetheJog DialtoINCREASEORDECREASEthevoltage(and#ofcellsin
series (C))
• PresstheJog Dial to save the voltage value
If no parameters are flashing, you can rotate the Jog Dial to select another
programsuchasCHARGE,BALANCE,FASTCHGorSTORAGE.
To start discharging,press and hold the Jog Dialfor3seconds.
8LI-IO BATTERIES
Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial
tolocatethePROGRAMSELECTLiIoBATTscreen.PresstheJog Dial to select
LiIo.
Rotate the Jog Dialtogotooneofthecontrolscreens(BALANCE,CHARGE,FAST
CHG,STORAGEorDISCHARGE)todowhatyourbatteryneeds.
Correctlyconnectyourlithiumbatterytothecharger(chargingconnectorrstand
balancingconnectorsecond).PresstheJog Dial and adjust the charging param-
eters as needed. Press and hold the Jog Dial(approximately3seconds)untilthe
screenchangestostartthebatterycheck/chargesequence.
R: 3SER S:3SER
CONFIRM (ENTER)
AWhen the charge cycle starts, the
charger compares the battery to
charger settings. The screen will
show the battery and your settings
information.IftheinformationafterR:(charger)andS:(settings)(A) does not
match, press the Mode key and change the lithium battery charging parameters
as needed. If the R: information matches S:,press the Jog Dial to confirm.
Afterconrmation,chargingstartsandinformationwillshowontheLCDscreen
(informationmayvary).
LI 3S 2.0A 12.59V
BAL 022:43 01082
F E
B C D
A
A. ALi-Iobatterypackis
balance charging
B. Batterypackhas3cellsin
series
C. Chargingrateis2.0A(2000mAh)
D. Voltagebeingappliedtothebatteryiscurrently12.59V
E. Presentchargelevelofthebatteryis1082mAh
F. Timeelapsedsincethechargeprocessstartedis22:43
During charging, the Jog Dial can be rotated counterclockwise to show several
parametermessagesontheLCDscreen,including:EndVoltage,InputPowerVolt-
age,External&InternalTemperature,TemperatureCutoff,SafetyTimerStatusand
CapacityCutoff.
Rotate the Jog Dial clockwise to show the charge voltages for each cell. Press the
Jog DialatanytimetoreturntotheChargeMonitorscreen.Thechargersignals
whenthecharging(ordischarging)processiscomplete(ifBuzzerissettoON).
CAUTION:TheLi-IoprogrammenusaretobeusedONLYforthe
charginganddischargingofLi-Iobatteries.Thechargingofotherbattery
types using these programs will result in damage to the battery or
charger.
CAUTION:Usingachargeratethatisnotcompatiblewiththebattery
capacities may result in damage or malfunction of the charger or
batteries.
9LI-IO BALANCE CHARGING
Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial
tolocatethePROGRAMSELECTLiIoBATTscreen.PresstheJog Dial to go into
this menu.
Rotate the Jog DialtogototheLiIoBALANCEscreenandsetchargingparam-
eters. The charging amperage (A)canbesetbetween0.1and10.0A.Voltage(B)
isdependentonthenumberofcellsinseries.Forexample,withLi-Iobatteries
thesevaluescanbefrom3.6V(for1Sbatteries)to21.6V(for6Sbatteries).
LiIo BALANCE
5.5A 21.6V(6S)
A B C
To select values other than the existing parameters:
• PresstheJog Dial so the charge current value (A) flashes
• RotatetheJog DialtoINCREASEORDECREASEthechargecurrentvalue
• PresstheJog Dial to save the value and the voltage value (B) flashes
• RotatetheJog DialtoINCREASEORDECREASEthevoltage(and#ofcellsin
series (C))
• PresstheJog Dial to save the voltage value
If no parameters are flashing, you can rotate the Jog Dial to select another
programsuchasCHARGE,FASTCHG,STORAGEorDISCHARGE.
To start charging,press and hold the Jog Dialfor3seconds.
10 LI-IO CHARGING
Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial
tolocatethePROGRAMSELECTLiIoBATTscreen.PresstheJog Dial to go into
this menu.
Rotate the Jog DialtogototheLiIoCHARGEscreenandsetchargingparameters.
The charging amperage (A)canbesetbetween0.1and10.0A.Voltage(B) is
dependentonthenumberofcellsinseries.Forexample,withLi-Iobatteriesthese
valuescanbefrom3.6V(for1Sbatteries)to21.6V(for6Sbatteries).
LiIo CHARGE
4.6A 21.6V(6S)
A B C
To select values other than the existing parameters:
• PresstheJog Dial so the charge current value (A) flashes
• RotatetheJog DialtoINCREASEORDECREASEthechargecurrentvalue
• PresstheJog Dial to save the value and the voltage value (B) flashes
• RotatetheJog DialtoINCREASEORDECREASEthevoltage(and#ofcellsin
series (C))
• PresstheJog Dial to save the voltage value
If no parameters are flashing, you can rotate the Jog Dial to select another
programsuchasBALANCE,FASTCHG,STORAGEorDISCHARGE.
To start charging,press and hold the Jog Dialfor3seconds.
CAUTION: If at any time during the charge process the battery becomes
hot or begins to puff, disconnect the battery immediately and discontinue
the charge process as batteries can cause fire, collateral damage and
injuries.
11 LI-IO FAST CHARGING
Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial
tolocatethePROGRAMSELECTLiIoBATTscreen.PresstheJog Dial to go into
this menu.
Rotate the Jog DialtogototheLiIoFASTCHGscreenandsetchargingparam-
eters. The charging amperage (A)canbesetbetween0.1and10.0A.Voltage(B)
isdependentonthenumberofcellsinseries.Forexample,withLi-Iobatteries
thesevaluescanbefrom3.6V(for1Sbatteries)to21.6V(for6Sbatteries).
Neartheendofastandardchargingcycle,thechargerswitchesfromConstant
Current(CC)modetoConstantVoltage(CV)modetoslowly“topoff”thecurrentin
the battery as close as possible to the maximum capacity.
InFastCharge,theCVmodeiseliminatedinordertogreatlyshortenthecharging
time; however,the final capacity of the battery will be less than what you would get
using the standard charge method.
LiIo FAST CHG
5.0A 21.6V(6S)
A B C
To select values other than the existing parameters:
• PresstheJog Dial so the charge current value (A) flashes
• RotatetheJog DialtoINCREASEORDECREASEthechargecurrentvalue
• PresstheJog Dial to save the value and the voltage value (B) flashes
• RotatetheJog DialtoINCREASEORDECREASEthevoltage(and#ofcellsin
series (C))
• PresstheJog Dial to save the voltage value
If no parameters are flashing, you can rotate the Jog Dial to select another
programsuchasCHARGE,BALANCE,STORAGEorDISCHARGE.
To start charging,press and hold the Jog Dialfor3seconds.
12 LI-IO STORAGE CHARGING
Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial
tolocatethePROGRAMSELECTLiIoBATTscreen.PresstheJog Dial to go into
this menu.
Rotate the Jog DialtogototheLiIoSTORAGEscreenandsetchargingparam-
eters. The charging amperage (A)canbesetbetween0.1and10.0A.Voltage(B)
isdependentonthenumberofcellsinseries.Forexample,withLi-Iobatteries
thesevaluescanbefrom3.6V(for1Sbatteries)to21.6V(for6Sbatteries).
Ifyoudon’tplanonusingyourbatteryforalongtime,itisbesttocharge(or
discharge)thebatterytoitsoptimalstoragevoltageandcapacity.
LiIo STORAGE
2.5A 21.6V(6S)
A B C
To select values other than the existing parameters:
• PresstheJog Dial so the charge current value (A) flashes
• RotatetheJog DialtoINCREASEORDECREASEthechargecurrentvalue
• PresstheJog Dial to save the value and the voltage value (B) flashes
• RotatetheJog DialtoINCREASEORDECREASEthevoltage(and#ofcellsin
series (C))
• PresstheJog Dial to save the voltage value
If no parameters are flashing, you can rotate the Jog Dial to select another
programsuchasCHARGE,BALANCE,FASTCHGorDISCHARGE.
To start charging,press and hold the Jog Dialfor3seconds.
1 SELFTESTANDPROGRAMSELECTSCREENS
LI-FE
2 LI-FEBATTERIES
3 LI-FEBALANCECHARGING
4 LI-FECHARGING
5 LI-FEFASTCHARGING
6 LI-FESTORAGECHARGING
7 LI-FEDISCHARGE
LI-IO
8 LI-IOBATTERIES
9 LI-IOBALANCECHARGING
10 LI-IOCHARGING
11 LI-IOFASTCHARGING
12 LI-IOSTORAGECHARGING
13 LI-IODISCHARGE
LI-PO
14 LI-POBATTERIES
15 LI-POBALANCECHARGING
16 LI-POCHARGING
17 LI-POFASTCHARGING
18 LI-POSTORAGECHARGING
19 LI-PODISCHARGE
NI-MH
20 NI-MH BATTERIES
21 NI-MHCHARGING
22 NI-MHAUTOCHARGING
23 NI-MHDISCHARGE
24 NI-MHRE-PEAKCHARGING
25 NI-MHCYCLECHARGING
NI-CD
26 NI-CDBATTERIES
27 NI-CDCHARGING
28 NI-CDAUTOCHARGING
29 NI-CDDISCHARGE
30 NI-CDRE-PEAKCHARGING
31 NI-CDCYCLECHARGING
PB
32 PB BATTERIES
33 PBCHARGING
34 PBDISCHARGE
PROGRAMMING AND OPERATIONS
35 BATTERY MEMORY
36 SYSTEM SET
aREST TIME
bSAFETY TIMER
c CAPACITYCUTOFF
d KEYBEEP/BUZZER
e INPUTPOWERLOWCUTOFF
f EXTERNALANDINTERNALTEMPERATURES
g RESETFACTORYSETTINGS
h VERSION
37 LIBATTERYVOLTAGECHECKEROPERATION-US-
INGTHEBALANCEADAPTERPORT
38 USBACCESSORYCHARGEROPERATION(COM-
PATIBLEWITHIPHONEANDIPODDEVICES)
39 TROUBLESHOOTINGGUIDE
Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial
tolocatethePROGRAMSELECTLiIoBATTscreen.PresstheJog Dial to go into
this menu.
Rotate the Jog DialtogototheLiIoDISCHARGEscreenandsetdischarging
parameters. The discharging amperage (A)canbesetbetween0.1and5.0A.Volt-
age (B)isdependentonthenumberofcellsinseries.Forexample,withLi-Iobat-
teriesthesevaluescanbefrom3.6V(for1Sbatteries)to21.6V(for6Sbatteries).
A battery’s capacity can be verified by discharging it to its minimum voltage level
and measuring the current as the battery is discharged.
LiIo DISCHARGE
2.0A 21.6V(6S)
A B C
To select values other than the existing parameters:
• PresstheJog Dial so the discharge current value (A) flashes
• RotatetheJog DialtoINCREASEORDECREASEthedischargecurrentvalue
• PresstheJog Dial to save the value and the voltage value (B) flashes
13 LI-IO DISCHARGING
14 LI-PO BATTERIES
Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial
tolocatethePROGRAMSELECTLiPoBATTscreen.PresstheJog Dial to select
LiPo.
Rotate the Jog Dialtogotooneofthecontrolscreens(BALANCE,CHARGE,FAST
CHG,STORAGEorDISCHARGE)todowhatyourbatteryneeds.
Correctlyconnectyourlithiumbatterytothecharger(chargingconnectorrstand
balancingconnectorsecond).PresstheJog Dial and adjust the charging param-
eters as needed. Press and hold the Jog Dial(approximately3seconds)untilthe
screenchangestostartthebatterycheck/chargesequence.
R: 3SER S:3SER
CONFIRM (ENTER)
AWhen the charge cycle starts, the
charger compares the battery to the
charger settings. The screen will
show the battery and your settings
information.IftheinformationafterR:(charger)andS:(settings)(A) does not
match, press the Mode key and change the lithium battery charging parameters
as needed. If the R: information matches S:,press the Jog Dial to confirm.
Afterconrmation,chargingstartsandinformationwillshowontheLCDscreen
(informationmayvary).
LI 3S 2.0A 12.59V
BAL 022:43 01082
F E
B C D
A
A. ALi-Pobatterypackis
balance charging
B. Batterypackhas3cellsin
series
C. Chargingrateis2.0A(2000mAh)
D. Voltagebeingappliedtothebatteryiscurrently12.59V
E. Presentchargelevelofthebatteryis1082mAh
F. Timeelapsedsincethechargeprocessstartedis22:43
During charging, the Jog Dial can be rotated counterclockwise to show several
parametermessagesontheLCDscreen,including:EndVoltage,InputPowerVolt-
age,External&InternalTemperature,TemperatureCutoff,SafetyTimerStatusand
CapacityCutoff.
Rotate the Jog Dial clockwise to show the charge voltages for each cell. Press the
Jog DialatanytimetoreturntotheChargeMonitorscreen.Thechargersignals
whenthecharging(ordischarging)processiscomplete(ifBuzzerissettoON).
CAUTION:TheLi-PoprogrammenusaretobeusedONLYforthe
charginganddischargingofLi-Pobatteries.Thechargingofother
battery types using these programs will result in damage to the battery
or charger.
CAUTION:Usingachargeratethatisnotcompatiblewiththebattery
capacities may result in damage or malfunction of the charger or
batteries.
15 LI-PO BALANCE CHARGING
Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial
tolocatethePROGRAMSELECTLiPoBATTscreen.PresstheJog Dial to go into
this menu.
Rotate the Jog DialtogototheLiPoBALANCEscreenandsetchargingparam-
eters. The charging amperage (A)canbesetbetween0.1and10.0A.Voltage(B)
isdependentonthenumberofcellsinseries.Forexample,withLi-Pobatteries
thesevaluescanbefrom3.7V(for1Sbatteries)to22.2V(for6Sbatteries).
LiPo BALANCE
5.5A 22.2V(6S)
A B C
To select values other than the existing parameters:
• PresstheJog Dial so the charge current value (A) flashes
• RotatetheJog DialtoINCREASEORDECREASEthechargecurrentvalue
• PresstheJog Dial to save the value and the voltage value (B) flashes
• RotatetheJog DialtoINCREASEORDECREASEthevoltage(and#ofcellsin
series (C))
• PresstheJog Dial to save the voltage value
If no parameters are flashing, you can rotate the Jog Dial to select another
programsuchasCHARGE,FASTCHG,STORAGEorDISCHARGE.
To start charging,press and hold the Jog Dialfor3seconds.
TABLE OF CONTENTS
16 LI-PO CHARGING
Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial
tolocatethePROGRAMSELECTLiPoBATTscreen.PresstheJog Dial to go into
this menu.
Rotate the Jog DialtogototheLiPoCHARGEscreenandsetchargingparam-
eters. The charging amperage (A)canbesetbetween0.1and10.0A.Voltage(B)
isdependentonthenumberofcellsinseries.Forexample,withLi-Pobatteries
thesevaluescanbefrom3.7V(for1Sbatteries)to22.2V(for6Sbatteries).
LiPo CHARGE
4.6A 22.2V(6S)
A B C
To select values other than the existing parameters:
• PresstheJog Dial so the charge current value (A) flashes
• RotatetheJog DialtoINCREASEORDECREASEthechargecurrentvalue
• PresstheJog Dial to save the value and the voltage value (B) flashes
• RotatetheJog DialtoINCREASEORDECREASEthevoltage(and#ofcellsin
series (C))
• PresstheJog Dial to save the voltage value
If no parameters are flashing, you can rotate the Jog Dial to select another
programsuchasBALANCE,FASTCHG,STORAGEorDISCHARGE.
To start charging,press and hold the Jog Dialfor3seconds.
CAUTION: If at any time during the charge process the battery becomes
hot or begins to puff, disconnect the battery immediately and discontinue
the charge process as batteries can cause fire, collateral damage and
injuries.
LITHIUM BATTERIES (Li-Fe)
LITHIUM BATTERIES (Li-Po)
Pb BATTERIES
Ni-Cd BATTERIES
Ni-MH BATTERIES
LITHIUM BATTERIES (Li-Ion)
BATTERY MEMORY
LITHIUM BATTERY METER
SYSTEM SET
• RotatetheJog DialtoINCREASEORDECREASEthevoltage(and#ofcellsin
series (C))
• PresstheJog Dial to save the voltage value
If no parameters are flashing, you can rotate the Jog Dial to select another
programsuchasCHARGE,BALANCE,FASTCHGorSTORAGE.
To start discharging,press and hold the Jog Dialfor3seconds.

20 NI-MH BATTERIES
27 NI-CD CHARGING
17 LI-PO FAST CHARGING
Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial
tolocatethePROGRAMSELECTLiPoBATTscreen.PresstheJog Dial to go into
this menu.
Rotate the Jog DialtogototheLiPoFASTCHGscreenandsetchargingparam-
eters. The charging amperage (A)canbesetbetween0.1and10.0A.Voltage(B)
isdependentonthenumberofcellsinseries.Forexample,withLi-Pobatteries
thesevaluescanbefrom3.7V(for1Sbatteries)to22.2V(for6Sbatteries).
Neartheendofastandardchargingcycle,thechargerswitchesfromConstant
Current(CC)modetoConstantVoltage(CV)modetoslowly“topoff”thecurrentin
the battery as close as possible to the maximum capacity.
InFastCharge,theCVmodeiseliminatedinordertogreatlyshortenthecharging
time; however,the final capacity of the battery will be less than what you would get
using the standard charge method.
LiPo FAST CHG
4.0A 7.4V(2S)
A B C
To select values other than the existing parameters:
• PresstheJog Dial so the charge current value (A) flashes
• RotatetheJog DialtoINCREASEORDECREASEthechargecurrentvalue
• PresstheJog Dial to save the value and the voltage value (B) flashes
• RotatetheJog DialtoINCREASEORDECREASEthevoltage(and#ofcellsin
series (C))
• PresstheJog Dial again to save the voltage value
If no parameters are flashing, you can rotate the Jog Dial to select another
programsuchasCHARGE,BALANCE,STORAGEorDISCHARGE.
To start charging,press and hold the Jog Dialfor3seconds.
18 LI-PO STORAGE CHARGING
Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial
tolocatethePROGRAMSELECTLiPoBATTscreen.PresstheJog Dial to go into
this menu.
Rotate the Jog DialtogototheLiPoSTORAGEscreenandsetchargingparam-
eters. The charging amperage (A)canbesetbetween0.1and10.0A.Voltage(B)
isdependentonthenumberofcellsinseries.Forexample,withLi-Pobatteries
thesevaluescanbefrom3.7V(for1Sbatteries)to22.2V(for6Sbatteries).
Ifyoudon’tplanonusingyourbatteryforalongtime,itisbesttocharge(or
discharge)thebatterytoitsoptimalstoragevoltageandcapacity.
LiPo STORAGE
2.5A 11.1V(3S)
A B C
To select values other than the existing parameters:
• PresstheJog Dial so the charge current value (A) flashes
• RotatetheJog DialtoINCREASEORDECREASEthechargecurrentvalue
• PresstheJog Dial to save the value and the voltage value (B) flashes
• RotatetheJog DialtoINCREASEORDECREASEthevoltage(and#ofcellsin
series (C))
• PresstheJog Dial to save the voltage value
If no parameters are flashing, you can rotate the Jog Dial to select another
programsuchasCHARGE,BALANCE,FASTCHGorDISCHARGE.
To start charging,press and hold the Jog Dialfor3seconds.
19 LI-PO DISCHARGING
Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial
tolocatethePROGRAMSELECTLiPoBATTscreen.PresstheJog Dial to go into
this menu.
Rotate the Jog DialtogototheLiPoDISCHARGEscreenandsetdischarging
parameters. The discharging amperage (A)canbesetbetween0.1and5.0A.Volt-
age (B)isdependentonthenumberofcellsinseries.Forexample,withLi-Pobat-
teriesthesevaluescanbefrom3.7V(for1Sbatteries)to22.2V(for6Sbatteries).
A battery’s capacity can be verified by discharging it to its minimum voltage level
and measuring the current as the battery is discharged.
LiPo DISCHARGE
2.0A 22.2V(6S)
A B C
To select values other than the existing parameters:
• PressJog Dial so the discharge current value (A) flashes
• RotatetheJog DialtoINCREASEORDECREASEthedischargecurrentvalue
• PresstheJog Dial to save the value and the voltage value (B) flashes
• RotatetheJog DialtoINCREASEORDECREASEthevoltage(and#ofcellsin
series (C))
• PressJog Dial to save the voltage value
If no parameters are flashing, you can rotate the Jog Dial to select another
programsuchasCHARGE,BALANCE,FASTCHGorSTORAGE.
To start discharging,press and hold the Jog Dialfor3seconds.
Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial
tolocatethePROGRAMSELECTNiMHBATTscreen.PresstheJog Dial to select
NiMH.
Rotate the Jog Dialtogotooneofthecontrolscreens(CHARGE,AutoCHARGE,
DISCHARGE,RE-PEAKorCYCLE)todowhatyourbatteryneeds.
CorrectlyconnectyourNi-MHbatterytothecharger.PresstheJog Dial and adjust
the charging parameters as needed. Press and hold the Jog Dial(approximately3
seconds)untilthescreenchangestostartthebatterycheck/chargesequence.
Afterconrmation,chargingstartsandinformationwillshowontheLCDscreen
(informationmayvary).
NiMH 2.0A 7.59V
CHG 022:43 01082
E D
B C
A
A. A Ni-MH battery pack is
charging
B. Chargingrateis2.0A
(2000mAh)
C. Voltagebeingappliedtothebatteryiscurrently7.59V
D. Presentchargelevelofthebatteryis1082mAh
E. Timeelapsedsincethechargeprocessstartedis22:43
During charging, the Jog Dial can be rotated counterclockwise to show several
parametermessagesontheLCDscreen,including:Ni-MHSensitivity,InputPower
Voltage,External&InternalTemperature,TemperatureCutoff,SafetyTimerStatus
andCapacityCutoff.Thechargersignalswhenthecharging(ordischarging)
processiscomplete(ifBuzzerissettoON).
CAUTION:TheNi-MHprogrammenusaretobeusedONLYforthe
charging and discharging of Ni-MH battery packs. The charging of other
battery types using these programs will result in damage to the battery
or charger.
CAUTION:Usingachargeratethatisnotcompatiblewiththebattery
capacities may result in damage or malfunction of the charger or
batteries.
21 NI-MH CHARGING
Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial
tolocatethePROGRAMSELECTNiMHBATTscreen.PresstheJog Dial to go into
this menu.
Rotate the Jog DialtogototheNiMHCHARGEscreenandsetchargingparam-
eters. The charging amperage (A)canbesetbetween0.1and10.0A.
NiMH CHARGE
CURRENT 1.0A
A
To select a value other than the existing parameter:
• PresstheJog Dial so the charge current value (A) flashes
• RotatetheJog DialtoINCREASEORDECREASEthechargecurrentvalue
• PresstheJog Dial to save the value
If no parameters are flashing, you can rotate the Jog Dial to select another
programsuchasAutoCHARGE,DISCHARGE,RE-PEAKorCYCLE.
To start charging,press and hold the Jog Dialfor3seconds.
22 NI-MH AUTO CHARGING
Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial
tolocatethePROGRAMSELECTNiMHBATTscreen.PresstheJog Dial to go into
this menu.
Rotate the Jog DialtogototheNiMHAutoCHARGEscreenandsetcharging
parameters. The charging amperage (A)canbesetbetween0.1and10.0A.
NiMH Auto CHARGE
CURRENT 1.0A
A
To select a value other than the existing parameter:
• PresstheJog Dial so the charge current value (A) flashes
• RotatetheJog DialtoINCREASEORDECREASEthechargecurrentvalue
• PresstheJog Dial to save the value
If no parameters are flashing, you can rotate the Jog Dial to select another
programsuchasCHARGE,DISCHARGE,RE-PEAKorCYCLE.
To start charging,press and hold the Jog Dialfor3seconds.
23 NI-MH DISCHARGING
Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial
tolocatethePROGRAMSELECTNiMHBATTscreen.PresstheJog Dial to go into
this menu.
Rotate the Jog DialtogototheNiMHDISCHARGEscreenandsetdischarging
parameters. The discharging amperage (A)canbesetbetween0.1and5.0A.
A battery’s capacity can be verified by discharging it to its minimum voltage level
and measuring the current as the battery is discharged. The discharge level can be
setfrom0.1to25.2V.
NiMH DISCHARGE
0.1A CUT: 1.0V
A B
To select a value other than the existing parameter:
• PresstheJog Dial so the discharge current value (A) flashes
• RotatetheJog DialtoINCREASEORDECREASEthedischargecurrentvalue
• PresstheJog Dial to save the value and the cutoff voltage value (B) flashes
• RotatetheJog DialtoINCREASEORDECREASEthecutoffvoltage
• PresstheJog Dial to save the voltage value
If no parameters are flashing, you can rotate the Jog Dial to select another
programsuchasCHARGE,AutoCHARGE,RE-PEAKorCYCLE.
To start discharging,press and hold the Jog Dialfor3seconds
24 NI-MH RE-PEAK CHARGING
Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial
tolocatethePROGRAMSELECTNiMHBATTscreen.PresstheJog Dial to go into
this menu.
Rotate the Jog DialtogototheNiMHRE-PEAKscreenandsetre-peakparam-
eterstoavalueofbetween1and3.
NiMH RE-PEAK
1
To select a value other than the existing parameter:
• PresstheJog Dial so the re-peak value (A) flashes
• RotatetheJog DialtoINCREASEORDECREASEthevalue
• PresstheJog Dial to save the value
If no parameters are flashing, you can rotate the Jog Dial to select another
programsuchasCHARGE,AutoCHARGE,DISCHARGEorCYCLE.
Press the Jog Dial to go to the next menu.
25 NI-MH CYCLE CHARGING
Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial
tolocatethePROGRAMSELECTNiMHBATTscreen.PresstheJog Dial to go into
this menu.
Rotate the Jog DialtogototheNiMHCYCLEscreenandsetcharge/discharge
cycle count parameters.
Thebatterycanbeputthroughaseriesofcharge/dischargecyclesusingthis
program.CyclingNi-MHbatteriescanincreasecapacityandrejuvenateneglected
batteries. Discharge capacity and average battery voltage help you compare batter-
ies for the best run time and power.
NiMH CYCLE
CHG>DCHG 5
A B
To select values other than the existing parameter:
• PresstheJog Dial so the cycle type (A) flashes
• RotatetheJog DialtosetthecycletypeasCHG>DCHGorDCHG>CHG
• PresstheJog Dial to save your choice and the number of cycles (B) flashes
• RotatetheJog Dialtosetthecyclecountbetween1to5
• PresstheJog Dial to save the cycle count value
If no parameters are flashing, you can rotate the Jog Dial to select another
programsuchasCHARGE,AutoCHARGE,DISCHARGEorRE-PEAK.
To start cycling,press and hold the Jog Dialfor3seconds.
26 NI-CD BATTERIES
Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial
tolocatethePROGRAMSELECTNiCdBATTscreen.PresstheJog Dial to select
NiCd.
Rotate the Jog Dialtogotooneofthecontrolscreens(CHARGE,AutoCHARGE,
DISCHARGE,RE-PEAKorCYCLE)todowhatyourbatteryneeds.
CorrectlyconnectyourNi-Cdbatterytothecharger.PresstheJog Dial and adjust
the charging parameters as needed. Press and hold the Jog Dial(approximately3
seconds)untilthescreenchangestostartthebatterycheck/chargesequence.
Afterconrmation,chargingstartsandinformationwillshowontheLCDscreen
(informationmayvary).
NiCd 2.0A 7.59V
CHG 022:43 01082
E D
B C
A
A. ANi-Cdbatterypackis
charging
B. Chargingrateis2.0A
(2000mAh)
C. Voltagebeingappliedtothebatteryiscurrently7.59V
D. Presentchargelevelofthebatteryis1082mAh
E. Timeelapsedsincethechargeprocessstartedis22:43
During charging, the Jog Dial can be rotated counterclockwise to show several
parametermessagesontheLCDscreen,including:Ni-CdSensitivity,InputPower
Voltage,External&InternalTemperature,TemperatureCutoff,SafetyTimerStatus
andCapacityCutoff.Thechargersignalswhenthecharging(ordischarging)
processiscomplete(ifBuzzerissettoON).
CAUTION:TheNi-CdprogrammenusaretobeusedONLYforthe
charginganddischargingofNi-Cdbatterypacks.Thechargingofother
battery types using these programs will result in damage to the battery
or charger.
CAUTION:Usingachargeratethatisnotcompatiblewiththebattery
capacities may result in damage or malfunction of the charger or
batteries.
Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial
tolocatethePROGRAMSELECTNiCdBATTscreen.PresstheJog Dial to go into
this menu.
Rotate the Jog DialtogototheNiCdCHARGEscreenandsetchargingparam-
eters. The charging amperage (A)canbesetbetween0.1and10.0A.
NiCd CHARGE
CURRENT 1.0A
A
To select a value other than the existing parameter:
• PresstheJog Dial so the charge current value (A) flashes
• RotatetheJog DialtoINCREASEORDECREASEthechargecurrentvalue
• PresstheJog Dial to save the value
If no parameters are flashing, you can rotate the Jog Dial to select another
programsuchasAutoCHARGE,DISCHARGE,RE-PEAKorCYCLE.
To start charging,press and hold the Jog Dialfor3seconds.
28 NI-CD AUTO CHARGING
Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial
tolocatethePROGRAMSELECTNiCdBATTscreen.PresstheJog Dial to go into
this menu.
Rotate the Jog DialtogototheNiCdAutoCHARGEscreenandsetcharging
parameters. The charging amperage (A)canbesetbetween0.1and10.0A.
NiCd Auto CHARGE
CURRENT 1.0A
A
To select a value other than the existing parameter:
• PresstheJog Dial so the charge current value (A) flashes
• RotatetheJog DialtoINCREASEORDECREASEthechargecurrentvalue
• PresstheJog Dial to save the value
If no parameters are flashing, you can rotate the Jog Dial to select another
programsuchasCHARGE,DISCHARGE,RE-PEAKorCYCLE.
To start charging,press and hold the Jog Dialfor3seconds.
29 NI-CD DISCHARGING
Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial
tolocatethePROGRAMSELECTNiCdBATTscreen.PresstheJog Dial to go into
this menu.
Rotate the Jog DialtogototheNiCdDISCHARGEscreenandsetdischarging
parameters. The discharging amperage (A)canbesetbetween0.1and5.0A.
A battery’s capacity can be verified by discharging it to its minimum voltage level
and measuring the current as the battery is discharged. The discharge level can be
setfrom0.1to25.2V.
NiCd DISCHARGE
0.1A CUT: 1.0V
A B
To select a value other than the existing parameter:
• PresstheJog Dial so the discharge current value (A) flashes
• RotatetheJog DialtoINCREASEORDECREASEthedischargecurrentvalue
• PresstheJog Dial to save the value and the cutoff voltage value (B) flashes
• RotatetheJog DialtoINCREASEORDECREASEthecutoffvoltage
• PresstheJog Dial to save the voltage value
If no parameters are flashing, you can rotate the Jog Dial to select another
programsuchasCHARGE,AutoCHARGE,RE-PEAKorCYCLE.
To start discharging,press and hold the Jog Dialfor3seconds
30 NI-CD RE-PEAK CHARGING
Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial
tolocatethePROGRAMSELECTNiCdBATTscreen.PresstheJog Dial to go into
this menu.
Rotate the Jog DialtogototheNiCdRE-PEAKscreenandsetre-peakparameters
toavalueofbetween1and3.
NiCd RE-PEAK
1
To select a value other than the existing parameter:
• PresstheJog Dial so the re-peak value (A) flashes
• RotatetheJog DialtoINCREASEORDECREASEthevalue
• PresstheJog Dial to save the value
If no parameters are flashing, you can rotate the Jog Dial to select another
programsuchasCHARGE,AutoCHARGE,DISCHARGEorCYCLE.
Press the Jog Dial to go to the next menu.
31 NI-CD CYCLE CHARGING
Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial
tolocatethePROGRAMSELECTNiCdBATTscreen.PresstheJog Dial to go into
this menu.
Rotate the Jog DialtogototheNiCdCYCLEscreenandsetcharge/discharge
cycle count parameters.
Thebatterycanbeputthroughaseriesofcharge/dischargecyclesusingthis
program.CyclingNi-Cdbatteriescanincreasecapacityandrejuvenateneglected
batteries. Discharge capacity and average battery voltage help you compare batter-
ies for the best run time and power.
NiCd CYCLE
CHG>DCHG 5
A B
To select values other than the existing parameter:
• PresstheJog Dial so the cycle type (A) flashes
• RotatetheJog DialtosetthecycletypeasCHG>DCHGorDCHG>CHG
• PresstheJog Dial to save your choice and the number of cycles (B) flashes
• RotatetheJog Dialtosetthecyclecountbetween1to5
• PresstheJog Dial to save the cycle count value
If no parameters are flashing, you can rotate the Jog Dial to select another
programsuchasCHARGE,AutoCHARGE,DISCHARGEorRE-PEAK.
To start cycling,press and hold the Jog Dialfor3seconds.
32 PB BATTERIES
Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial
tolocatethePROGRAMSELECTPbBATTscreen.PresstheJog Dial to select Pb.
Rotate the Jog Dialtogotooneofthecontrolscreens(CHARGEorDISCHARGE)
to do what your battery needs.
ThenatureofaLeadAcidorSealedLeadAcidbatteryisverydifferentfromthatof
Lithium,Ni-MHorNi-Cdbatteries.TheoutputcurrentofaPbbatteryislowerthan
other batteries relative to their capacities. Furthermore, lead acid batteries can’t be
chargedatalevelgreaterthan1/10theircapacity.
Forexample,a5000mAhleadacidbatterycan’tbechargedatarategreaterthan
0.5A.Formoredetailsonthechargeanddischargecapabilitiesofyourbattery,
please refer to the charging data supplied by the battery manufacturer.
CorrectlyconnectyourPbbatterytothecharger.PresstheJog Dial and adjust
the charging parameters as needed. Press and hold the Jog Dial(approximately3
seconds)untilthescreenchangestostartthebatterycheck/chargesequence.
Afterconrmation,chargingstartsandinformationwillshowontheLCDscreen
(informationmayvary).
Pb-6 0.4A 12.39V
CHG 022:43 01082
F E
B C D
A
A.ALeadAcidbatterypackis
charging
B.Batterypackhas6cells
in series
C.Chargingatarateof0.4A(400mAh)
D. Voltagebeingappliedtothebatteryiscurrently12.39V
E.Presentchargelevelofthebatteryis1082mAh
F. Timeelapsedsincethechargeprocessstartedis22:43
During charging, the Jog Dial can be rotated counterclockwise to show several
parametermessagesontheLCDscreen,including:EndVoltage,CapacityCutoff,
SafetyTimerStatus,TemperatureCutoffandInputPowerVoltage.Thecharger
signalswhenthecharging(ordischarging)processiscomplete(ifBuzzerissetto
ON).
CAUTION:ThePbprogrammenusaretobeusedONLYforthecharging
and discharging of Pb battery packs. The charging of other battery types
using these programs will result in damage to the battery or charger.
CAUTION:Usingachargeratethatisnotcompatiblewiththebattery
capacities may result in damage or malfunction of the charger or
batteries.
33 PB CHARGING
Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial
tolocatethePROGRAMSELECTPbBATTscreen.PresstheJog Dial to go into
this menu.
Rotate the Jog DialtogotothePbCHARGEscreenandsetchargingparameters.
The charging amperage (A)canbesetbetween0.1and10.0A.
Pb CHARGE
0.1A 2.0V (1P)
A B
To select values other than the existing parameters:
• PresstheJog Dial so the charge current value (A) flashes
• RotatetheJog DialtoINCREASEORDECREASEthechargecurrentvalue
• PresstheJog Dial to save the charge current value and the battery voltage
value (B) flashes
• RotatetheJog DialtoINCREASEORDECREASEthebatteryvoltage/cellcount
value(Pbbatteriesare2.0Vpercell,fora6cellbatterythiswouldbe2.0Vx6
cell=12.0V)
• PresstheJog Dial to save the voltage
If no parameters are flashing, you can rotate the Jog Dial to select another
programsuchasDISCHARGE.
To start charging,press and hold the Jog Dialfor3seconds.
34 PB DISCHARGING
Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial
tolocatethePROGRAMSELECTPbBATTscreen.PresstheJog Dial to go into
this menu.
Rotate the Jog DialtogotothePbDISCHARGEscreenandsetdischarging
parameters. The discharging amperage (A)canbesetbetween0.1and5.0A.
A battery’s capacity can be verified by discharging it to its minimum voltage level
and measuring the current as the battery is discharged. The discharge level can be
setfrom2to20V.
Pb DISCHARGE
0.1A 2.0V (1P)
A B
To select values other than the existing parameters:
• PresstheJog Dial so the discharge current value (A) flashes
• RotatetheJog DialtoINCREASEORDECREASEthedischargecurrentvalue
• PresstheJog Dial to save the value and the cutoff voltage value (B) flashes
• RotatetheJog DialtoINCREASEORDECREASEthecutoffvoltage
• PresstheJog Dial to save the voltage value
If no parameters are flashing, you can rotate the Jog Dial to select another
programsuchasCHARGE.
To start discharging,press and hold the Jog Dialfor3seconds
35 BATTERY MEMORY
Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial
tolocatethePROGRAMSELECTBATTMEMORYscreen.PresstheJog Dial to
select BATT MEMORY.
Usethismenutocreateabatteryprole.Toreducethetimerequiredtoinitiatea
charging or discharging cycle on a battery you regularly use, this charger has been
designedwiththecapabilityofstoringupto10batteryprolesthatcanbequickly
accessed and run at a later time.
• RotatetheJog Dialtoidentifyabatteryprole,1through10
• PresstheJog Dialtoselectbatteryprole1
• PresstheJog Dial so battery type flashes
• RotatetheJog Dial to select a battery type
• PresstheJog Dial to save the battery type
Follow this process using the Jog Dial to select, change, then save each param-
eter(batteryvoltage,chargecurrent,dischargecurrent,dischargevoltage,Terminal
VoltageControl(TVC)andtemperaturecutoff).Thensavethebatteryprole.
• RotatetheJog DialtoselectSAVEPROGRAM
• PresstheJog Dial to save the program
• Repeatthisprocesstoenteradditionalbatteryproles
• PresstheMode key until you reach the 9 main menus
CAUTION:IncreasingtheTVCvaluebeyondthedefaultsettingsmayresultina
shorterbatterylifeand/ordamagetothebattery.DonotchangetheTVCvalue
unlessyoufullyunderstandtheeffectsTVCwillhaveonyourbattery.
ToChargeorDischargeabatteryusingthesavedprole:
Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial
tolocatethePROGRAMSELECTBATTMEMORYscreen.PresstheJog Dial to
select BATT MEMORY.
• RotatetheJog Dialtoidentifythebatteryprole,1through10.
• PressandholdtheJog Dialfor3seconds
• RotatetheJog Dial to choose the type of charge function you wish to perform
• PressandholdtheJog Dialfor3secondstostart
36 SYSTEM SET
Press the Mode key until you reach the 9 main menus, then rotate the Jog DialtolocatethePROGRAMSELECTSYSTEMSETscreen.PresstheJog Dial to select
SYSTEM SET.
Usethismenutosetthe“behindthescenes”operatingparametersforthischargersuchas;RestTime,SafetyTimer,CapacityCutoff,KeyBeep/Buzzer,InputPowerLow
Cutoff,ExternalandInternalTemperatures,LoadFactorySettingsandVersion.
37 LI BATTERY VOLTAGE CHECKER OPERATION - USING THE BALANCE ADAPTER PORT
ThePassport™UltraDuochargerhasthecapabilitytoreadanddisplaytheindi-
vidualcellvoltagesofaLi-Po,Li-FeorLi-Iobattery.Thisvoltagecheckingfunction
can only be used when the charger is powered ON and not charging a battery.
Tousethevoltagechecker,connectthebalanceportconnectorofyourLi-Po,Li-Fe
orLi-IobatterytothebalanceadapterboardconnectedtotheBalanceCircuit
AdapterBoardConnector(C).
Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial
tolocatethePROGRAMSELECTLIBATTMETERscreen.PresstheJog Dial to
selectLIBATTMETER.
In a few moments, the charger will begin to display the cell voltages of the battery
in the following format:
3.70 3.70 0.00 V
0.00 0.00 0.00 V
Thisexampleisfora2Sbattery,soonlythevoltagesforthesetwocellsare
displayed. The data is presented in this format:
1–1 1–2 1–3 V
1–4 1-5 1–6 V
At this point, you can rotate the Jog Dial to see a display of the overall battery
voltage as well as the individual high- and low-cell voltage values.
MAIN 08.20V
H4.104V L4098V
You may exit this menu at any time by pressing the Mode key to return to the
main menus.
38 USB ACCESSORY CHARGER OPERATION (COMPATIBLE WITH iPhone AND iPod DEVICES)
ThePassportUltraDuochargerhasthecapabilitytochargeyouriPhone,iPodorUSBcompatibledevicewiththe1AUSBchargeport(E).Tousethechargingfunction,
simplyconnectacompatiblechargingdeviceorcordintothechargeportwhilethechargerispoweredON.TheinternalUSBchargeportwillprovideupto1Acurrentat
5VDC.
aREST TIME
UsethismenutosettheResttimeduringeachstepinacycle.WhenaNi-MH
orNi-CDbatteryiscycled(charged,dischargedandchargedagain)itwillget
hot, therefore it is necessary to set a rest time interval during each step of the
process to make sure the battery and charger are completely cooled before
movingontothenextpartofthecycle.Defaulttimeis10minutes,butthis
canbesetbetween1and60minutes.Toselectavalueotherthanthedefault
parameter:
•PresstheJog Dial to select Rest Time
•PresstheJog Dial so the Rest Time value flashes
•RotatetheJog Dial to select Rest Time in Minutes
•PresstheJog Dial to save the Rest Time value
•RotatetheJog Dial to select SAFETY TIMER
bSAFETY TIMER
Usethismenutosetatimelimitforchargingabattery.Whenachargecycle
is started, a clock inside the charger will begin recording the elapsed charge
time. If the SAFETY TIMER function has been turned ON,the charger will stop
the charging process once this time limit has been reached to avoid damage
causedbyover-chargingthebattery.Thistimevaluecanbesetbetween1and
720minutes.
To select values other than the default parameters:
•PresstheJog DialsotheON/OFFvalueashes
•RotatetheJog Dial to select ON or OFF
•PresstheJog Dial to save the value
•RotatetheJog Dial to select the value for time
•PresstheJog Dial to save the value
•RotatetheJog DialtoselectCapacityCutoff
cCAPACITY CUTOFF
Usethismenutosetacapacitylimitatwhichthechargerwillstopcharginga
battery.When a charge cycle starts, the charger records the battery capacity.
WhentheCapacityCutofffunctionissetatON,thechargerwillstopchargingat
thecapacitylimittopreventbatterydamage.Capacitycanbeadjustedbetween
100and50,000mAh.
•PresstheJog DialsotheON/OFFvalueashes
•RotatetheJog Dial to select ON or OFF
•PresstheJog Dial to save the value
•RotatetheJog DialtoselecttheCapacityCutoffvalue
•PresstheJog Dial to save the value
•RotatetheJog DialtoselectKeyBeep/Buzzer
dKEY BEEP/BUZZER
UsethismenutosetthekeybeepandchargeralarmbuzzeratONorOFFas
needed. We recommend that you keep the alarm ON so the alarm will sound
when charging is complete or if there is cause for alarm during charging.
To select values other than the default parameters:
• PresstheJog DialsotheKeyBeepON/OFFvalueashes
• RotatetheJog Dial to select ON or OFF
• PresstheJog Dial to save the value
• PresstheJog DialsotheBuzzerON/OFFvalueashes
• RotatetheJog Dial to select ON or OFF
• PresstheJog Dial to save the value
• Rotatethe Jog DialtoselectInputPowerLowCutoff
eINPUT POWER LOW CUTOFF
Usethismenutosettheinputvoltagelimitsoanalarmwillsoundifthevoltage
goes below the cutoff value. The voltage alarm value can be set anywhere from
10.0to11.0V.
To select a value other than the default parameter:
• PresstheJog Dial so the voltage value flashes
• RotatetheJog Dial to select the voltage value
• PresstheJog Dial to save the value
• Rotatethe Jog Dial to select External and Internal Temperatures
fEXTERNAL AND INTERNAL TEMPERATURES
By selecting the External and Internal Temperatures Screen you can view the
currenttemperaturesofboththebattery(external)andthecharger(internal).
Theoptionaltemperaturesensor(DYN5033)isrequiredforexternaltemperature
measurement.
gRESET FACTORY SETTINGS
• PresstheJog Dial to reset the charger to factory settings
• Pressthe Jog DialtoselectVERSION
hVERSION
ByselectingtheVersionScreenyoucanviewtheversion(revisionnumber)ofthe
software on your charger.
39 TROUBLESHOOTING GUIDE
LCDScreenWarningandErrormessagesshownbelow.
Duringchargeroperation,circuitsmonitorbatteryandchargerfunctions.Ifthefollowingmessagesshowonthecharger’sLCDscreen,maketherecommendedresponses.
If the message continues after you respond as recommended, contact your nearest Horizon Hobby customer service center for assistance.
REVERSEPOLARITY Make sure each connection polarity is correct between the power source and the charger,then between the charger and the batter y
CONNECTIONBREAK Make sure the power connections are correct for charging
SHORT ERR Make sure there are no short circuits between the poles of the battery or the battery and the charger. Replace damaged wires.
INPUTVOLERR Input voltage to the charger fell below the default or adjusted input voltage setting. Make sure the power source for the charger provides correct
input voltage.
VOLSELECTERR Incorrectsettingforcellinseriescount(packvoltage)ofalithiumbattery.Makechargersettingsmatchthebatterypacklabelcellinseriescount
specifications or replace the battery.
BREAKDOWN Chargerelectronicsrequirerepair.
BATTERYCHECKLOWVOLTAGE Battery voltage is lower than the value setting in the charger. Adjust settings, then make sure the battery is not damaged or replace the battery.
BATTERYCHECKHIGHVOLTAGE Battery voltage is higher than the value setting in the charger. Adjust settings, then make sure the battery is not damaged or replace the battery.
Battery Type Li-Po Li-Io Li-Fe Ni-MH Ni-Cd Pb
Standardvoltage(Voltspercell) 3.70 3.60 3.30 1.20 1.20 2.00
Max.voltage(Voltspercell) 4.20 4.10 3.60 1.60 1.60 2.45
Min.voltage(Voltspercell) 3.00 3.00 2.00 1.00 0.85 1.75
You may exit this menu at any time by pressing the Mode key to return to the main menus.

1 YEAR LIMITED WARRANTY
What this Warranty Covers - Horizon Hobby, Inc., (Horizon)
warrants to the original purchaser that the product purchased (the
“Product”) will be free from defects in materials and workmanship
for a period of 1 years from the date of purchase.
What is Not Covered - This warranty is not transferable and does
not cover (i) cosmetic damage, (ii) damage due to acts of God,
accident, misuse, abuse, negligence, commercial use, or due to im-
proper use, installation, operation or maintenance, (iii) modification
of or to any part of the Product, (iv) attempted service by anyone
other than a Horizon Hobby authorized service center, (v) Product
not purchased from an authorized Horizon dealer, or (vi) Product not
compliant with applicable technical regulations.
OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES
NO OTHER WARRANTY OR REPRESENTATION, AND HEREBY
DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING,
WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF NON-IN-
FRINGEMENT, MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. THE PURCHASER ACKNOWLEDGES THAT THEY ALONE
HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE
REQUIREMENTS OF THE PURCHASER’S INTENDED USE.
Purchaser’s Remedy - Horizon’s sole obligation and purchaser’s
sole and exclusive remedy shall be that Horizon will, at its option,
either (i) service, or (ii) replace, any Product determined by Horizon
to be defective. Horizon reserves the right to inspect any and all
Product(s) involved in a warranty claim. Service or replacement
decisions are at the sole discretion of Horizon. Proof of purchase is
required for all warranty claims. SERVICE OR REPLACEMENT AS
PROVIDED UNDER THIS WARRANTY IS THE PURCHASER’S SOLE
AND EXCLUSIVE REMEDY.
Limitation of Liability - HORIZON SHALL NOT BE LIABLE FOR
SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES,
LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN
ANY WAY, REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN
CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY OR
ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Further, in no
event shall the liability of Horizon exceed the individual price of the
Product on which liability is asserted. As Horizon has no control over
use, setup, final assembly, modification or misuse, no liability shall
be assumed nor accepted for any resulting damage or injury. By the
act of use, setup or assembly, the user accepts all resulting liability.
If you as the purchaser or user are not prepared to accept the
liability associated with the use of the Product, purchaser is advised
to return the Product immediately in new and unused condition to
the place of purchase.
Law - These terms are governed by Illinois law (without regard to
conflict of law principals). This warranty gives you specific legal
rights, and you may also have other rights which vary from state to
state. Horizon reserves the right to change or modify this warranty
at any time without notice.
WARRANTY SERVICES
Questions, Assistance, and Services - Your local hobby store
and/or place of purchase cannot provide warranty support or
service. Once assembly, setup or use of the Product has been
started, you must contact your local distributor or Horizon directly.
This will enable Horizon to better answer your questions and service
you in the event that you may need any assistance. For questions
or assistance, please visit our website at www.horizonhobby.com,
submit a Product Support Inquiry, or call 877.504.0233 toll free to
speak to a Product Support representative.
Inspection or Services - If this Product needs to be inspected
or serviced and is compliant in the country you live and use the
Product in, please use the Horizon Online Service Request submis-
sion process found on our website or call Horizon to obtain a Return
Merchandise Authorization (RMA) number. Pack the Product se-
curely using a shipping carton. Please note that original boxes may
be included, but are not designed to withstand the rigors of ship-
ping without additional protection. Ship via a carrier that provides
tracking and insurance for lost or damaged parcels, as Horizon is
not responsible for merchandise until it arrives and is accepted
at our facility. An Online Service Request is available at http://
www.horizonhobby.com/content/_service-center_render-service-
center. If you do not have internet access, please contact Horizon
Product Support to obtain a RMA number along with instructions
for submitting your product for service. When calling Horizon, you
will be asked to provide your complete name, street address, email
address and phone number where you can be reached during busi-
ness hours. When sending product into Horizon, please include your
RMA number, a list of the included items, and a brief summary of
the problem. A copy of your original sales receipt must be included
for warranty consideration. Be sure your name, address, and RMA
number are clearly written on the outside of the shipping carton.
NOTICE: Do not ship LiPo batteries to Horizon. If you have
any issue with a LiPo battery, please contact the appropriate
Horizon Product Support office.
Warranty Requirements- For Warranty consideration, you
must include your original sales receipt verifying the proof-
of-purchase date. Provided warranty conditions have been met,
your Product will be serviced or replaced free of charge. Service or
replacement decisions are at the sole discretion of Horizon.
Non-Warranty Service - Should your service not be covered
by warranty, service will be completed and payment will be
required without notification or estimate of the expense un-
less the expense exceeds 50% of the retail purchase cost. By
submitting the item for service you are agreeing to payment of the
service without notification. Service estimates are available upon
request. You must include this request with your item submitted for
service. Non-warranty service estimates will be billed a minimum of
½ hour of labor. In addition you will be billed for return freight. Ho-
rizon accepts money orders and cashier’s checks, as well as Visa,
MasterCard, American Express, and Discover cards. By submitting
any item to Horizon for service, you are agreeing to Horizon’s Terms
and Conditions found on our website http://www.horizonhobby.com/
content/_service-center_render-service-center.
NOTICE: Horizon service is limited to Product compliant in
the country of use and ownership. If non-compliant product
is received by Horizon for service, it will be returned unser-
viced at the sole expense of the purchaser.
WARRANTY AND SERVICE CONTACT INFORMATION
Country of Purchase Horizon Hobby Address Phone Number/Email Address
United States of America
Horizon Service Center
(Electronics and engines) 4105 Fieldstone Rd
Champaign, Illinois, 61822 USA
877-504-0233
Online Repair Request: visit
www.horizonhobby.com/service
Horizon Product Support
(All other products)
877-504-0233
[e-mail]
United Kingdom Horizon Hobby Limited
Units 1-4 , Ployters Rd, Staple Tye,
Harlow, Essex, CM18 7NS
United Kingdom
[phone]
[e-mail]
Germany Horizon Technischer
Service
Christian-Junge-Straße 1
25337 Elmshorn, Germany
[phone]
[email protected]
France Horizon Hobby SAS 11 Rue Georges Charpak
77127 Lieusaint, France
[phone]
[e-mail]
PARTS CONTACT INFORMATION
Country of Purchase Horizon Hobby Address Phone Number/Email Address
United States of America Sales 4105 Fieldstone Rd
Champaign, Illinois, 61822 USA
800-338-4639
[e-mail]
United Kingdom Horizon Hobby Limited
Units 1-4, Ployters Rd, Staple Tye
Harlow, Essex, CM18 7NS
United Kingdom
[phone]
[e-mail]
Germany Horizon Hobby GmbH Christian-Junge-Straße 1
25337 Elmshorn, Germany
[phone]
[email protected]
France Horizon Hobby SAS 11 Rue Georges Charpak
77127 Lieusaint, France
[phone]
[e-mail]
COMPLIANCE INFORMATION FOR THE EUROPEAN UNION
Declaration of Conformity (in accordance with ISO/IEC 17050-1)
No. HH2012101001
Product(s): DYN 200WX2 Multi Chemistry Dual AC/DC Battery Charger
Item Number(s): DYN4300EU, DYN4300UK
The object of declaration described above is in conformity with the requirements of the specifications listed below, following the provisions of
the European EMC Directive 2004/108/EC and LVD Directive 2006/95/EC:
EN55022: 2010
EN55024: 2010
EN61000-3-2:2006+A1:2009+A2:2009
EN61000-3-3:2008
EN60335-1: 2002+A11:2004+A1:2004+A12:2006+A2:2006+A13:2008+A14:2010+A15:2011
EN60335-2-29:2004+A2:2010
Signed for and on behalf of:
Horizon Hobby, Inc.
Champaign, IL USA
Oct 10, 2012
Steven A. Hall
Executive Vice President and Chief Operating Officer
International Operations and Risk Management
Horizon Hobby, Inc.
Instructions for disposal of WEEE by users in the European Union
This product must not be disposed of with other waste. Instead, it is the user’s responsibility to dispose of their waste equipment
by handing it over to a designated collections point for the recycling of waste electrical and electronic equipment. The separate
collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that
it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste
equipment for recycling, please contact your local city office, your household waste disposal service or where you purchased the product.
GARANTIE UND SERVICE INFORMATIONEN
Garantiezeitraum - Exklusive Garantie Horizon Hobby Inc
(Horizon) garantiert, dass das gekaufte Produkt frei von Mate-
rial- und Montagefehlern ist. Der Garantiezeitraum entspricht
den gesetzlichen Bestimmung des Landes, in dem das Produkt
erworben wurde. In Deutschland beträgt der Garantiezeitraum 6
Monate und der Gewährleistungszeitraum 18 Monate nach dem
Garantiezeitraum.
Einschränkungen der Garantie - (a) Die Garantie wird nur dem
Erstkäufer (Käufer) gewährt und kann nicht übertragen werden. Der
Anspruch des Käufers besteht in der Reparatur oder dem Tausch im
Rahmen dieser Garantie. Die Garantie erstreckt sich ausschließlich
auf Produkte, die bei einem autorisierten Horizon Händler erworben
wurden. Verkäufe an dritte werden von dieser Garantie nicht
gedeckt. Garantieansprüche werden nur angenommen, wenn ein
gültiger Kaufnachweis erbracht wird. Horizon behält sich das Recht
vor, diese Garantiebestimmungen ohne Ankündigung zu ändern
oder modifizieren und widerruft dann bestehende Garantiebestim-
mungen.
(b) Horizon übernimmt keine Garantie für die Verkaufbarkeit des
Produktes, die Fähigkeiten und die Fitness des Verbrauchers für
einen bestimmten Einsatzzweck des Produktes. Der Käufer allein ist
dafür verantwortlich, zu prüfen, ob das Produkt seinen Fähigkeiten
und dem vorgesehenen Einsatzzweck entspricht.
(c) Ansprüche des Käufers Es liegt ausschließlich im Ermessen
von Horizon, ob das Produkt, bei dem ein Garantiefall festgestellt
wurde, repariert oder ausgetauscht wird. Dies sind die exklusiven
Ansprüche des Käufers, wenn ein Defekt festgestellt wird. Horizon
behält sich vor, alle eingesetzten Komponenten zu prüfen, die in
den Garantiefall einbezogen werden können. Die Entscheidung zur
Reparatur oder zum Austausch liegt nur bei Horizon. Die Garantie
schließt kosmetische Defekte oder Defekte, hervorgerufen durch
höhere Gewalt, falsche Behandlung des Produktes, falscher
Einsatz des Produktes, kommerziellen Einsatz oder Modifikationen
irgendwelcher Art aus. Die Garantie schließt Schäden, die durch
falschen Einbau, falsche Handhabung, Unfälle, Betrieb, Service
oder Reparaturversuche, die nicht von Horizon ausgeführt wurden
aus. Rücksendungen durch den Käufer direkt an Horizon oder eine
seiner Landesvertretung bedürfen der Schriftform.
Schadensbeschränkung - Horizon ist nicht für direkte oder
indirekte Folgeschäden, Einkommensausfälle oder kommerzielle
Verluste, die in irgendeinem Zusammenhang mit dem Produkt
stehen verantwortlich, unabhängig ab ein Anspruch im Zusam-
menhang mit einem Vertrag, der Garantie oder der Gewährleistung
erhoben werden. Horizon wird darüber hinaus keine Ansprüche aus
einem Garantiefall akzeptieren, die über den individuellen Wert des
Produktes hinaus gehen. Horizon hat keinen Einfluss auf den Ein-
bau, die Verwendung oder die Wartung des Produktes oder etwaiger
Produktkombinationen, die vom Käufer gewählt werden. Horizon
übernimmt keine Garantie und akzeptiert keine Ansprüche für in
der folge auftretende Verletzungen oder Beschädigungen. Mit der
Verwendung und dem Einbau des Produktes akzeptiert der Käufer
alle aufgeführten Garantiebestimmungen ohne Einschränkungen
und Vorbehalte. Wenn Sie als Käufer nicht bereit sind, diese Bestim-
mungen im Zusammenhang mit der Benutzung des Produktes zu
akzeptieren, werden Sie gebeten, dass Produkt in unbenutztem
Zustand in der Originalverpackung vollständig bei dem Verkäufer
zurückzugeben.
Sicherheitshinweise - Dieses ist ein hochwertiges Hobby Produkt
und kein Spielzeug. Es muss mit Vorsicht und Umsicht eingesetzt
werden und erfordert einige mechanische wie auch mentale
Fähigkeiten. Ein Versagen, das Produkt sicher und umsichtig zu
betreiben kann zu Verletzungen von Lebewesen und Sachbeschä-
digungen erheblichen Ausmaßes führen. Dieses Produkt ist nicht
für den Gebrauch durch Kinder ohne die Aufsicht eines Erziehungs-
berechtigten vorgesehen. Die Anleitung enthält Sicherheitshinweise
und Vorschriften sowie Hinweise für die Wartung und den Betrieb
des Produktes. Es ist unabdingbar, diese Hinweise vor der ersten
Inbetriebnahme zu lesen und zu verstehen. Nur so kann der falsche
Umgang verhindert und Unfälle mit Verletzungen und Beschädigun-
gen vermieden werden.
Fragen, Hilfe und Reparaturen - Ihr lokaler Fachhändler und die
Verkaufstelle können eine Garantiebeurteilung ohne Rücksprache
mit Horizon nicht durchführen. Dies gilt auch für Garantierepara-
turen. Deshalb kontaktieren Sie in einem solchen Fall den Händler,
der sich mit Horizon kurz schließen wird, um eine sachgerechte
Entscheidung zu fällen, die Ihnen schnellst möglich hilft.
Wartung und Reparatur - Muss Ihr Produkt gewartet oder
repariert werden, wenden Sie sich entweder an Ihren Fachhändler
oder direkt an Horizon. Rücksendungen/Reparaturen werden nur
mit einer von Horizon vergebenen RMA Nummer bearbeitet. Diese
Nummer erhalten Sie oder ihr Fachhändler vom technischen
Service. Mehr Informationen dazu erhalten Sie im Serviceportal
unter www. Horizonhobby.de oder telefonisch bei dem technischen
Service von Horizon. Packen Sie das Produkt sorgfältig ein.
Beachten Sie, dass der Originalkarton in der Regel nicht ausreicht,
um beim Versand nicht beschädigt zu werden. Verwenden Sie einen
Paketdienstleister mit einer Tracking Funktion und Versicherung, da
Horizon bis zur Annahme keine Verantwortung für den Versand des
Produktes übernimmt. Bitte legen Sie dem Produkt einen Kaufbeleg
bei, sowie eine ausführliche Fehlerbeschreibung und eine Liste aller
eingesendeten Einzelkomponenten. Weiterhin benötigen wir die
vollständige Adresse, eine Telefonnummer für Rückfragen, sowie
eine Email Adresse.
Garantie und Reparaturen - Garantieanfragen werden nur
bearbeitet, wenn ein Originalkaufbeleg von einem autorisierten
Fachhändler beiliegt, aus dem der Käufer und das Kaufdatum
hervorgeht. Sollte sich ein Garantiefall bestätigen wird das Produkt
repariert oder ersetzt. Diese Entscheidung obliegt einzig Horizon
Hobby.
Kostenpflichtige Reparaturen - Liegt eine kostenpflichtige
Reparatur vor, erstellen wir einen Kostenvoranschlag, den wir
Ihrem Händler übermitteln. Die Reparatur wird erst vorgenommen,
wenn wir die Freigabe des Händlers erhalten. Der Preis für die
Reparatur ist bei Ihrem Händler zu entrichten. Bei kostenpflichtigen
Reparaturen werden mindestens 30 Minuten Werkstattzeit und
die Rückversandkosten in Rechnung gestellt. Sollten wir nach 90
Tagen keine Einverständniserklärung zur Reparatur vorliegen haben,
behalten wir uns vor, das Produkt zu vernichten oder anderweitig
zu verwerten.
ACHTUNG: Kostenpflichtige Reparaturen nehmen wir nur
für Elektronik und Motoren vor. Mechanische Reparaturen,
besonders bei Hubschraubern und RC-Cars sind extrem auf-
wendig und müssen deshalb vom Käufer selbst vorgenom-
men werden.
GARANTIE UND SERVICE KONTAKTINFORMATIONEN
Land des Kauf Horizon Hobby Adresse Telefon/Email Adresse
Deutschland Horizon Technischer Service Christian-Junge-Straße 1
25337 Elmshorn, Germany
[phone]
[email protected]
KUNDENDIENSTINFORMATIONEN
Land des Kauf Horizon Hobby Adresse Telefon/Email Adresse
Deutschland Horizon Hobby GmbH Christian-Junge-Straße 1
25337 Elmshorn, Germany
[phone]
[email protected]
RECHTLICHE INFORMATIONEN FÜR DIE EUROPÄISCHE UNION
Konformitätserklärung laut Allgemeine Anforderungen (ISO/IEC 17050-1:2004, korrigierte Fassung 2007-06-15); Deutsche
und Englische Fassung EN ISO/IEC 17050-1:2010
Declaration of conformity (in accordance with ISO/IEC 17050-1)
No. HH2012101001
Horizon Hobby GmbH
Christian-Junge-Straße 1
D-25337 Elmshorn
erklärt das Produkt: DYN 200WX2 Multi Chemistry Dual AC/DC Battery Charger, DYN4300EU, DYN4300UK
declares the product: DYN 200WX2 Multi Chemistry Dual AC/DC Battery Charger, DYN4300EU, DYN4300UK
den übrigen einschlägigen Bestimmungen des EMV-Richtlinie 2004/108/EC und LVD-Richtlinie 2006/95/EC.
complies with the essential requirements of the EMC Directive 2004/108/EC and LVD Directive 2006/95/EC.
Angewendete harmonisierte Normen:
Harmonized standards applied:
EN55022: 2010
EN55024: 2010
EN61000-3-2:2006+A1:2009+A2:2009
EN61000-3-3:2008
EN60335-1: 2002+A11:2004+A1:2004+A12:2006+A2:2006+A13:2008+A14:2010+A15:2011
EN60335-2-29:2004+A2:2010
Elmshorn
10.10.2012
Steven A. Hall
Geschäftsführer
Managing Director
Birgit Schamuhn
Geschäftsführerin
Managing Director
Horizon Hobby GmbH; Christian-Junge-Straße 1; D-25337 Elmshorn
HR Pi: HRB 1909; UStlDNr,:DE812678792; STR.NR.L 1829812324
Geschäftsführer: Birgit Schamuhn, Steven A. Hall -- Tel.: [phone] • Fax: [phone]
eMail: [email protected]; Internet: www.horizonhobby.de
Es gelten unsere allgemeinen Geschäftsbedingungen, die in unseren Geschäftsräumen eingesehen weden können.
Eare bleibt bis zur vollstandigen Bezahlung Eigentum der Horizon Hobby GmbH
Anweisungen zur Entsorgung von Elektro—und Elektronik-Altgeräten für Benutzer in der Europäischen Union
Dieses Produkt darf nicht zusammen mit anderem Abfall entsorgt werden. Stattdessen ist der Benutzer dafür verantwortlich,
unbrauchbare Geräte durch Abgabe bei einer speziellen Sammelstelle für das Recycling von unbrauchbaren elektrischen und
elektronischen Geräten zu entsorgen. Die separate Sammlung und das Recycling von unbrauchbaren Geräten zum Zeitpunkt
der Entsorgung hilft, natürliche Ressourcen zu bewahren und sicherzustellen, dass Geräte auf eine Weise wiederverwertet werden, bei der
die menschliche Gesundheit und die Umwelt geschützt werden. Weitere Informationen dazu, wo Sie unbrauchbare Geräte zum Recycling
abgeben können, erhalten Sie bei lokalen Ämtern, bei der Müllabfuhr für Haushaltsmüll sowie dort, wo Siedas Produkt gekauft haben.
FCC INFORMATION
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications.

GARANTIE ET RÉPARATIONS
Durée de la garantie - Garantie exclusive - Horizon Hobby,
Inc. (Horizon) garantit que le Produit acheté (le « Produit ») sera
exempt de défauts matériels et de fabrication à sa date d’achat par
l’Acheteur. La durée de garantie correspond aux dispositions légales
du pays dans lequel le produit a été acquis. La durée de garantie
est de 6 mois et la durée d’obligation de garantie de 18 mois à
l’expiration de la période de garantie.
Limitations de la garantie - (a) La garantie est donnée à
l’acheteur initial (« Acheteur ») et n’est pas transférable. Le recours
de l’acheteur consiste en la réparation ou en l‘échange dans le
cadre de cette garantie. La garantie s’applique uniquement aux
produits achetés chez un revendeur Horizon agréé. Les ventes
faites à des tiers ne sont pas couvertes par cette garantie. Les
revendications en garantie seront acceptées sur fourniture d’une
preuve d’achat valide uniquement. Horizon se réserve le droit de
modifier les dispositions de la présente garantie sans avis préalable
et révoque alors les dispositions de garantie existantes.
(b) Horizon n’endosse aucune garantie quant à la vendabilité du
produit ou aux capacités et à la forme physique de l’utilisateur pour
une utilisation donnée du produit. Il est de la seule responsabilité de
l’acheteur de vérifier si le produit correspond à ses capacités et à
l’utilisation prévue.
(c) Recours de l’acheteur – Il est de la seule discrétion d‘Horizon de
déterminer si un produit présentant un cas de garantie sera réparé
ou échangé. Ce sont là les recours exclusifs de l’acheteur lorsqu’un
défaut est constaté.
Horizon se réserve la possibilité de vérifier tous les éléments utilisés
et susceptibles d’être intégrés dans le cas de garantie. La décision
de réparer ou de remplacer le produit est du seul ressort d’Horizon.
La garantie exclut les défauts esthétiques ou les défauts provoqués
par des cas de force majeure, une manipulation incorrecte du
produit, une utilisation incorrecte ou commerciale de ce dernier ou
encore des modifications de quelque nature qu’elles soient.
La garantie ne couvre pas les dégâts résultant d’un montage ou
d’une manipulation erronés, d’accidents ou encore du fonc-
tionnement ainsi que des tentatives d’entretien ou de réparation
non effectuées par Horizon. Les retours effectués par le fait de
l’acheteur directement à Horizon ou à l’une de ses représentations
nationales requièrent une confirmation écrite.
Limitation des dégâts - Horizon ne saurait être tenu pour respon-
sable de dommages conséquents directs ou indirects, de pertes de
revenus ou de pertes commerciales, liés de quelque manière que
ce soit au produit et ce, indépendamment du fait qu’un recours
puisse être formulé en relation avec un contrat, la garantie ou
l’obligation de garantie. Par ailleurs, Horizon n’acceptera pas de
recours issus d’un cas de garantie lorsque ces recours dépassent
la valeur unitaire du produit. Horizon n’exerce aucune influence
sur le montage, l’utilisation ou la maintenance du produit ou sur
d’éventuelles combinaisons de produits choisies par l’acheteur.
Horizon ne prend en compte aucune garantie et n‘accepte aucun
recours pour les blessures ou les dommages pouvant en résulter.
En utilisant et en montant le produit, l’acheteur accepte sans
restriction ni réserve toutes les dispositions relatives à la garantie
figurant dans le présent document.
Si vous n’êtes pas prêt, en tant qu’acheteur, à accepter ces disposi-
tions en relation avec l’utilisation du produit, nous vous demandons
de restituer au vendeur le produit complet, non utilisé et dans son
emballage d’origine.
Indications relatives à la sécurité - Ceci est un produit de loisirs
perfectionné et non un jouet. Il doit être utilisé avec précaution
et bon sens et nécessite quelques aptitudes mécaniques ainsi
que mentales. L’incapacité à utiliser le produit de manière sûre et
raisonnable peut provoquer des blessures et des dégâts matériels
conséquents. Ce produit n’est pas destiné à être utilisé par des
enfants sans la surveillance par un tuteur. La notice d’utilisation
contient des indications relatives à la sécurité ainsi que des indica-
tions concernant la maintenance et le fonctionnement du produit.
Il est absolument indispensable de lire et de comprendre ces
indications avant la première mise en service. C’est uniquement
ainsi qu’il sera possible d’éviter une manipulation erronée et des
accidents entraînant des blessures et des dégâts.
Questions, assistance et réparations - Votre revendeur spé-
cialisé local et le point de vente ne peuvent effectuer une estimation
d’éligibilité à l’application de la garantie sans avoir consulté Horizon.
Cela vaut également pour les réparations sous garantie. Vous
voudrez bien, dans un tel cas, contacter le revendeur qui conviendra
avec Horizon d’une décision appropriée, destinée à vous aider le
plus rapidement possible.
Maintenance et réparation - Si votre produit doit faire l’objet
d’une maintenance ou d‘une réparation, adressez-vous soit à votre
revendeur spécialisé, soit directement à Horizon. Emballez le produit
soigneusement. Veuillez noter que le carton d‘emballage d’origine
ne suffit pas, en règle générale, à protéger le produit des dégâts
pouvant survenir pendant le transport. Faites appel à un service
de messagerie proposant une fonction de suivi et une assurance,
puisque Horizon ne prend aucune responsabilité pour l’expédition
du produit jusqu’à sa réception acceptée. Veuillez joindre une
preuve d’achat, une description détaillée des défauts ainsi qu’une
liste de tous les éléments distincts envoyés. Nous avons de plus
besoin d’une adresse complète, d’un numéro de téléphone (pour
demander des renseignements) et d’une adresse de courriel.
Garantie et réparations - Les demandes en garantie seront
uniquement traitées en présence d’une preuve d’achat originale
émanant d’un revendeur spécialisé agréé, sur laquelle figurent le
nom de l’acheteur ainsi que la date d’achat. Si le cas de garantie
est confirmé, le produit sera réparé Cette décision relève unique-
ment de Horizon Hobby.
Réparations payantes - En cas de réparation payante, nous
établissons un devis que nous transmettons à votre revendeur. La
réparation sera seulement effectuée après que nous ayons reçu la
confirmation du revendeur. Le prix de la réparation devra être ac-
quitté au revendeur. Pour les réparations payantes, nous facturons
au minimum 30 minutes de travail en atelier ainsi que les frais de
réexpédition. En l’absence d’un accord pour la réparation dans un
délai de 90 jours, nous nous réservons la possibilité de détruire le
produit ou de l’utiliser autrement.
ATTENTION: Nous n’effectuons de réparations payantes
que pour les composants électroniques et les moteurs. Les
réparations touchant à la mécanique, en particulier celles
des hélicoptères et des voitures radiocommandées, sont
extrêmement coûteuses et doivent par conséquent être ef-
fectuées par l’acheteur lui-même.
COORDONNÉES DE GARANTIE ET RÉPARATIONS
Pays d’achat Horizon Hobby Adresse Numéro de téléphone/Courriel
France Horizon Hobby SAS 11 Rue Georges Charpak
77127 Lieusaint, France
[phone]
[e-mail]
INFORMATIONS DE CONTACT POUR LES PIÈCES
Pays d’achat Horizon Hobby Adresse Numéro de téléphone/Courriel
France Horizon Hobby SAS 11 Rue Georges Charpak
77127 Lieusaint, France
[phone]
[e-mail]
INFORMATIONS DE CONFORMITÉ POUR L’UNION EUROPÉENNE
Déclaration de conformité (conformément à la norme ISO/IEC 17050-1)
No. HH2012101001
Produit(s): DYN 200WX2 Multi Chemistry Dual AC/DC Battery Charger
Numéro(s) d’article: DYN4300EU, DYN4300UK
L’objet de la déclaration décrit ci-dessus est en conformité avec les exigences des spécifications énumérées ci-après, suivant les conditions
de la directive CEM 2004/108/EC et LVD 2006/95/EC:
EN55022: 2010
EN55024: 2010
EN61000-3-2:2006+A1:2009+A2:2009
EN61000-3-3:2008
EN60335-1: 2002+A11:2004+A1:2004+A12:2006+A2:2006+A13:2008+A14:2010+A15:2011
EN60335-2-29:2004+A2:2010
Signé en nom et pour le compte de:
Horizon Hobby, Inc.
Champaign, IL USA
10.10.2012
Steven A. Hall
Vice-Président, Directeur Général
Gestion Internationale des Activités et des Risques
Horizon Hobby, Inc.
Elimination dans l’Union Européenne
Ce produit ne doit pas être éliminé avec les ordures ménagères. Il est de la responsabilité de l‘utilisateur de remettre le
produit à un point de collecte officiel des déchets d’équipements électriques. Cette procédure permet de garantir le respect de
l’environnement et l’absence de sollicitation excessive des ressources naturelles. Elle protège de plus le bien-être de la com-
munauté humaine. Pour plus d’informations quant aux lieux d’éliminations des déchets d‘équipements électriques, vous pouvez contacter
votre mairie ou le service local de traitement des ordures ménagères.
DURATA DELLA GARANZIA
Periodo di garanzia - Garanzia esclusiva - Horizon Hobby, Inc.,
(Horizon) garantisce che i prodotti acquistati (il “Prodotto”) sono
privi di difetti relativi ai materiali e di eventuali errori di montaggio.
Il periodo di garanzia è conforme alle disposizioni legali del paese
nel quale il prodotto è stato acquistato. Tale periodo di garanzia am-
monta a 6 mesi e si estende ad altri 18 mesi dopo tale termine.
Limiti della garanzia - (a) La garanzia è limitata all’acquirente
originale (Acquirente) e non è cedibile a terzi. L’acquirente ha il
diritto a far riparare o a far sostituire la merce durante il periodo
di questa garanzia. La garanzia copre solo quei prodotti acquistati
presso un rivenditore autorizzato Horizon. Altre transazioni di terze
parti non sono coperte da questa garanzia. La prova di acquisto
è necessaria per far valere il diritto di garanzia. Inoltre, Horizon si
riserva il diritto di cambiare o modificare i termini di questa garanzia
senza alcun preavviso e di escludere tutte le altre garanzie già
esistenti.
(b) Horizon non si assume alcuna garanzia per la disponibilità del
prodotto, per l’adeguatezza o l’idoneità del prodotto a particolari
previsti dall’utente. è sola responsabilità dell’acquirente il fatto di
verificare se il prodotto è adatto agli scopi da lui previsti.
(c) Richiesta dell’acquirente – spetta soltanto a Horizon, a propria
discrezione riparare o sostituire qualsiasi prodotto considerato
difettoso e che rientra nei termini di garanzia. queste sono le
uniche rivalse a cui l’acquirente si può appellare, se un prodotto è
difettoso.
Horizon si riserva il diritto di controllare qualsiasi componente
utilizzato che viene coinvolto nella rivalsa di garanzia. Le decisioni
relative alla sostituzione o alla riparazione avvengono solo in base
alla discrezione di Horizon. Questa garanzia non copre dei danni
superficiali o danni per cause di forza maggiore, uso errato del
prodotto, negligenza, uso ai fini commerciali, o una qualsiasi modi-
fica a qualsiasi parte del prodotto.
Questa garanzia non copre danni dovuti ad una installazione errata,
ad un funzionamento errato, ad una manutenzione o un tentativo
di riparazione non idonei a cura di soggetti diversi da Horizon. La
restituzione del prodotto a cura dell’acquirente, o da un suo rap-
presentante, deve essere approvata per iscritto dalla Horizon.
Limiti di danno - Horizon non si riterrà responsabile per danni
speciali, diretti, indiretti o consequenziali; perdita di profitto o di
produzione; perdita commerciale connessa al prodotto, indipen-
dentemente dal fatto che la richiesta si basa su un contratto o sulla
garanzia. Inoltre la responsabilità di Horizon non supera mai in
nessun caso il prezzo di acquisto del prodotto per il quale si chiede
la responsabilità. Horizon non ha alcun controllo sul montaggio,
sull’utilizzo o sulla manutenzione del prodotto o di combinazioni di
vari prodotti. Quindi Horizon non accetta nessuna responsabilità
per danni o lesioni derivanti da tali circostanze. Con l’utilizzo e il
montaggio del prodotto l’utente acconsente a tutte le condizioni,
limitazioni e riserve di garanzia citate in questa sede. Qualora
l’utente non fosse pronto ad assumersi tale responsabilità associata
all’uso del prodotto, si suggerisce di di restituire il prodotto intatto,
mai usato e immediatamente presso il venditore.
Indicazioni di sicurezza - Questo è un prodotto sofisticato di
hobbistica e non è un giocattolo. Esso deve essere manipolato
con cautela, con giudizio e richiede delle conoscenze basilari di
meccanica e delle facoltà mentali di base. Se il prodotto non verrà
manipolato in maniera sicura e responsabile potrebbero risultare
delle lesioni, dei gravi danni a persone, al prodotto o all’ambiente
circostante. Questo prodotto non è concepito per essere usato dai
bambini senza una diretta supervisione di un adulto. Il manuale
del prodotto contiene le istruzioni di sicurezza, di funzionamento
e di manutenzione del prodotto stesso. È fondamentale leggere e
seguire tutte le istruzioni e le avvertenze nel manuale prima di met-
tere in funzione il prodotto. Solo così si eviterà un utilizzo errato e di
preverranno incidenti, lesioni o danni.
Domande, assistenza e riparazioni - Il vostro negozio locale
e/o luogo di acquisto non possono fornire garanzie di assistenza o
riparazione senza previo colloquio con Horizon. questo vale anche
per le riparazioni in garanzia. Quindi in tale casi bisogna interpellare
un rivenditore, che si metterà in contatto subito con Horizon per
prendere una decisione che vi possa aiutare nel più breve tempo
possibile.
Manutenzione e riparazione - Se il prodotto deve essere ispezi-
onato o riparato, si prega di rivolgersi ad un rivenditore specializzato
o direttamente ad Horizon. il prodotto deve essere Imballato con
cura. Bisogna far notare che i box originali solitamente non sono
adatti per effettuare una spedizione senza subire alcun danno.
Bisogna effettuare una spedizione via corriere che fornisce una
tracciabilità e un’assicurazione, in quanto Horizon non si assume al-
cuna responsabilità in relazione alla spedizione del prodotto. Inserire
il prodotto in una busta assieme ad una descrizione dettagliata degli
errori e ad una lista di tutti i singoli componenti spediti. Inoltre ab-
biasmo bisogno di un indirizzo completo, di un numnero di telefono
per chiedere ulteriori domande e di un indirizzo e-mail.
Garanzia a riparazione - Le richieste in garanzia verranno
elaborate solo se è presente una prova d’acquisto in originale
proveniente da un rivenditore specializzato autorizzato, nella quale
è ben visibile la data di acquisto. Se la garanzia viene confermata,
allora il prodotto verrà riparato o sostituito. Questa decisione spetta
esclusivamente a Horizon Hobby.
Riparazioni a pagamento - Se bisogna effettuare una
riparazione a pagamento, effettueremo un preventivo che verrà
inoltrato al vostro rivenditore. La riparazione verrà effettuata dopo
l’autorizzazione da parte del vostro rivenditore. La somma per la
riparazione dovrà essere pagata al vostro rivenditore. Le riparazioni
a pagamento avranno un costo minimo di 30 minuti di lavoro e in
fattura includeranno le spese di restituzione. Qualsiasi riparazione
non pagata e non richiesta entro 90 giorni verrà considerata ab-
bandonata e verrà gestita di conseguenza.
ATTENZIONE: Le riparazioni a pagamento sono disponibili
solo sull’elettronica e sui motori. Le riparazioni a livello
meccanico, soprattutto per gli elicotteri e le vetture RC sono
molto costose e devono essere effettuate autonomamente
dall’acquirente.
GARANZIA E REVISIONA INFORMAZIONI PER I CONTATTI
Stato de acquistato Horizon Hobby Indirizzo Telefono/Indirizzo e-mail
Germania Horizon Technischer Service Christian-Junge-Straße 1
25337 Elmshorn, Germany
[phone]
[email protected]
INFORMAZIONI DI SERVIZIO CLIENTI
Stato de acquistato Horizon Hobby Indirizzo Telefono/Indirizzo e-mail
Germania Horizon Hobby GmbH Christian-Junge-Straße 1
25337 Elmshorn, Germany
[phone]
[email protected]
INFORMAZIONI SULLA CONFORMITÀ PER L’UNIONE EUROPEA
Dichiarazione di conformità (in conformità con ISO/IEC 17050-1)
No. HH2012101001
Prodotto(i): DYN 200WX2 Multi Chemistry Dual AC/DC Battery Charger
Numero(i) articolo: DYN4300EU, DYN4300UK
Gli oggetti presentati nella dichiarazione sopra citata sono conformi ai requisiti delle specifiche elencate qui di seguito, seguendo le dispo-
sizioni della direttiva europea EMC 2004/108/EC e LVD 2006/95/EC:
EN55022: 2010
EN55024: 2010
EN61000-3-2:2006+A1:2009+A2:2009
EN61000-3-3:2008
EN60335-1: 2002+A11:2004+A1:2004+A12:2006+A2:2006+A13:2008+A14:2010+A15:2011
EN60335-2-29:2004+A2:2010
Firmato per conto di:
Horizon Hobby, Inc.
Champaign, IL USA
10.10.2012
Steven A. Hall
Executive Vice President and Chief Operating Officer
International Operations and Risk Management
Horizon Hobby, Inc.
Istruzioni del RAEE per lo smaltimento da parte di utenti dell’Unione Europea
Questo prodotto non deve essere smaltito assieme ai rifiuti domestici. Al contrario, l’utente è responsabile dello smaltimento
di tali rifiuti che devono essere portati in un centro di raccolta designato per il riciclaggio di rifiuti elettrici e apparecchiature
elettroniche. La raccolta differenziata e il riciclaggio di tali rifiuti provenienti da apparecchiature nel momento dello smaltimento
aiuteranno a preservare le risorse naturali e garantiranno un riciclaggio adatto a proteggere il benessere dell’uomo e dell’ambiente. Per
maggiori informazioni sui centri di raccolta, contattare il proprio ufficio locale, il servizio di smaltimento rifiuti o il negozio presso il quale è
stato acquistato il prodotto.
©2012 Horizon Hobby Inc.
Dynamite, Passport, EC3 and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, Inc.
iPhone and iPod are trademarks of Apple, Inc., registered in the U.S. and other countries. Microsoft®, Windows XP®and Windows Vista®are
registered trademarks of the Microsoft Corporation.
Created 09/12 32772