SPECIFICATIONS Page 4
Input Power:
Display:
Decimal Point:
95 to 130 VAC, 50/60 Hz,
or
190to
260
VAC, 50/60 Hz, 6
VA
± 4
-1/2
Digit, 0.56" Red LED
Switch Selectable XXXXX. to
X.XXXX
Scale Factor Range:
Gain Adjust Pot:
Digital Calibrator:
Accuracy:
Stability:
5% to 200%
0.001 to 0.999
(0.000 =Calibration
of
1)
±0.1% -0/+1 Digit
Display Update Rate: Switch Selectable Operating Temperature: 0 to +50 °C. (32 to +122 of.)
Fast:
Slow: 2
Hz
(2
times persecond)
0.5 Hz (every
two
seconds) Dimensions:
Overall: 1.98" x 3.78" x 6.03"
Overvoltage Indication: Display FlashesAll
"O's"
50 mm x 96 mm x 150 mm
1.78" x 3.58" (-0/+0.04")
Cutout:
Signal Input Range: Switch Selectable 45 mm x
91
mm
(-0/+1 mm)
1/16" to 1/4"
o
to
± 20/200/600 VDC Panel Thickness:
Panel Depth: 5.68" (144 mm)
Weight: 1.4Ibs.
ORDERING INFORMATION
MODEL
STAOO
STAEO
STASO
DESCRIPTION
SimTach A Analog Input Speed Indicator, 115
VAC
Operation
SimTach A Analog Input Speed Indicator, 230
VAC
Operation
SimTach A Analog Input Speed Indicator, 115/230VAC Selectable Operation
SimTach A Analog Input Speed Indicator with Digital Calibration, 115
VAC
Operation
SimTach A Analog Input Speed Indicator with Digital Calibration, 230
VAC
Operation
STA01
STAE1
STAS1 SimTach A Analog Input Speed Indicator with Digital Calibration, 115/230VAC Selectable Operation
WARRANTY
Standard products manufactured by
the
Companyarewarranted
to
befree from defects inworkmanship and material
for
aperiodofoneyearfromthedate
of
shipment,and productswhich aredefectiveinworkmanshipormaterialwill be repaired
or
replaced, attheoption
ofthe
Company, atnochargetotheBuyer. Final determinationas
to
whethera productis actually
defective rests with the Company. The obligation of the Company hereunder shall be limited solely
to
repair
and
replacement
of
products that fall within the foregoing limitations, and shall be conditioned upon receipt by the Company
of
written notice of any alleged defects
or
deficiency promptly after discoverywithin the warranty period, and
in
the
case
of components or units purchased by the Company, the obligation
of
the Company shall not exceed the settlement
that
the Company is able to obtain from the supplierthereof.
No
products shall be returned
to
the Company without its
prior
consent. Products which the Company consents to have returned shall be shipped F.O.B. the Company's factory.
The
Company cannot assume responsibility
or
accept invoices for unauthorized repairs to its components, even
though
defective. The life ofthe products of
the
Company depends, to a large extent, upon thetype ofusagethereof, and
THE
COMPANY MAKES NO WARRANTYAS TO FITNESS OF ITS PRODUCTS FOR SPECIFICAPPLICATIONS
BY
THE
BUYER NOR AS
TO
PERIOD
OF
SERVICE UNLESS THE COMPANY SPECIFICALLY AGREES OTHERWISE
IN
WRITING AFTER THE PROPOSED USAGE HAS BEEN MADE KNOWN TO
IT.
THE FOREGOING WARRANTY IS EXCLUSIVE AND IN LIEU
OF
ALL OTHER WARRANTIES EXPRESSED
OR
IMPLIED, INCLUDING, BUT
NOT
LIMITED TO ANY WARRANTY
OF
MERCHANTABILITY OR
OF
FITNESS FOR A
PARTICULAR PURPOSE.
SERVICE:
Include:
Ifthis product requires service, call Dynapar Corp.
for
an
RMA
(Return Material Authorization)
number, pack it in a sturdy carton and ship prepaid to: Service Dept. at address below.
1. Description
of
problem 3. Purchase order number
2. Name of responsible person
4.
Return shipping instructions
DANAHER
CONTROLS
• 2100
W.
Broad St., P.O. Box 368, Elizabethtown, NC 28337 TEL: (847) 662-2666 FAX: (847}662-6633
160 0250 0132 Printed
in
U.S.A. April 20,
1992
