Dynascan XBP301 User manual

User Manual
For
Android Control Board
With
Wireless module
Product .：Digital Transmission System
Model No.：XBP301

This user manual pertains to Android player main board with wireless module, the main
board can be assembled in the Android based Advertising Media player, listed as below
Model
Model Description
66502
65”Monitor
66901
86”Monitor
Specifications
Item
Description
Storage
Internal：16GB NAND Flash, External：Micro SD Card
WIFI
802.11 b/g/n
Ethernet
RJ45, 10/100Mbps Fast Ethernet
Display Output
HDMI*2, DP*1
USB Input
USB Type A*1
Card Reader
Micro SD Card Slot*1
Power Input
12V/3A（6 pin header）
LED Indicator
Green（Power on）
Internet Browser
Google Chrome
Video Format
JPG H.264, H.263, DIVX, ON2VP, Mpeg1, Speak, Mpeg4,
VC-1, WMV9, MPEG2, Real video, SVC
Image Format
BMP, JPG, TIF, PNG, GIF
Music Format
MP3, WAV, WMA
PCBA Dimension：200 x 150 mm
Assemble method：The module will be screwed on the housing and used as a main
board for Android based Advertising Media Player.
Input port：
1pc Power jack –for +5V/2A power input
1pc USB Type A –for USB mouse
1pc Antenna connector for 2.4G WiFi network

Hardware interface

WIFI pin location and description：
PIN
SYMBOL
DESCRIPTION
PIN
SYMBOL
DESCRIPTION
1
NC
Not Connect
17
BT_SYNC_IN
2
NC
Not Connect
18
GND
GND
3
NC
Not Connect
19
NC
4
NC
Not Connect
20
GND
GND
5
GND
GND
21
GND
GND
6
WL_USB_DP
USB D+
22
NC
7
WL_USB_DN
USB D-
23
GND
GND
8
GND
GND
24
GND
GND
9
NC
Not Connect
25
GND
GND
10
NC
Not Connect
26
WLAN_WAKE_HOST
WLAN CHIP
WAKES UP HOST
11
GND
GND
27
NC
12
NC
Not Connect
28
CHIP_EN
Shutdown CHIP
（Internal 47KΩ
pull up to 3.3V,
low level active）
13
GND
GND
29
GND
GND
14
BT_WAKE_HOST
BT CHIP
WAKES UP HOST
30
VDD33
3.3V
15
NC
Not Connect
31
NC
Not Connect
16
NC
Not Connect
32
GND
GND

FCC Statement：
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
CAUTION：
Any changes or modifications not expressly approved by the grantee of this device could
void the user's authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
RF exposure warning：
This equipment must be installed and operated in accordance with provided instructions and
the antenna(s) used for this transmitter must be installed to provide a separation distance of
at least 20 cm from all persons and must not be co-located or operating in conjunction with
any other antenna or transmitter. End-users and installers must be provide with antenna
installation instructions and transmitter operating conditions for satisfying RF exposure
compliance.
End Product Labeling：
The end product shall bear the following 15.19 statement: This device complies with part 15
of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This transmitter module is authorized only for use in device where the antenna may be
installed such that 20cm may be maintained between the antenna and users. The final end
product must be labeled in a visible area with the following:
＂Contains FCC ID: 2AKWYXBP301＂

This module is intended under the following conditions：
1. This module is certified pursuant to Part 15 rules section(15.247).
2. This module is limited to host model number: 66502, 66901 / Brand: DynaScan
3. This module has been approved to operate with the antenna types listed below, with the
maximum permissible gain indicated.
Frequency Band
Antenna Type
Gain(dBi)
2400-2483.5MHz
PIFA
0.87
Information on test modes and additional testing requirements：
This module is restricted to integration into hosts for indoor use only.
Be limited the operation channels in channel 1-11 for 2.4GHz band.
The separate approval is required for all other operating configurations, including portable
configurations with respect to Part 2.1093 and different antenna configurations.
The information on how to configure test modes for host product evaluation for different
operational conditions for a stand-alone modular transmitter in a host, versus with multiple,
simultaneously transmitting modules or other transmitters in a host can be found at KDB
Publication 996369 D04.
Additional testing, Part 15 Subpart B disclaimer：
Appropriate measurements (e.g. 15B compliance) and if applicable additional equipment
authorizations (e.g. SDoC) of the host product to be addressed by the
integrator/manufacturer.
This module is only FCC authorized for the specific rule part 15.247 listed on the grant, and the
host product manufacturer is responsible for compliance to any other FCC rules that apply to
the host product as being Part 15 Subpart B compliant.
The user manual of the end product should include：
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate this equipment.
The antenna(s) used for this transmitter must be installed to provide a separation distance of
at least 20 cm from all persons.
This device and its antenna(s) must not be co-located or operating in conjunction with any
other antenna or transmitter.

For product available in the USA/Canada market, only channel 1~11 can be operated. Selection
of other channels is not possible.
Name: DynaScan Technology, Inc.
Address: 7 Chrysler, Irvine, CA 92618, USA
Office: +1 949.421.0348
https://www.dynascandisplay.com