Dynex DX-TRP58BL User manual

V1 ENGLISH 14-0369
Storing your tripod
1Remove your camera.
2Lower the center column.
3Push on any leg to close the tripod.
4Collapse the legs.
5Store the tripod in the carrying case.
Important safety instructions
• Make sure that all leg locks are correctly tightened and that the
legs are fully opened before use.
• Do not carry or transport your tripod with camera equipment
attached (for example, over your shoulder or cradled in your
arms).
• Do not expose your tripod to excessive heat or cold, or use near
any ame or re.
• Do not oil or grease any part of the tripod.
• Do not use any solvents or thinners to clean your tripod. Use
only a mild detergent and wipe dry with a soft, lint-free cloth.
• Do not exceed the load limit of this tripod.
Specications
Folded length: 22.1 in. (56 cm)
Maximum height: 58 in. (147.3 cm)
Minimum height: 21.3 in. (54 cm)
Weight: 2.2 lbs (1 kg)
Load capacity: 8.8 lbs (4 kg)
One-year limited warranty
Visit www.dynexproducts.com for details.
Contact Dynex:
For customer service, call 800-305-2204 (U.S. and Canada) or
01-800-926-3020 (Mexico)
www.dynexproducts.com
DYNEX is a registered trademark of BBY Solutions, Inc.
Registered in some countries.
Distributed by Best Buy Purchasing, LLC, 7601 Penn Ave South, Richeld, MN 55423 U.S.A.
©2014 BBY Solutions, Inc. All Rights Reserved.
QUICK SETUP GUIDE
DX-TRP58BL
58" Lightweight Tripod
Before using your new product, please read
these instructions to prevent any damage.

Leg
lock
Center column
Elevation locking
knob
Elevation crank
Mounting plate
Locking lever
Package contents
• Tripod
• Carrying case
• Quick Setup Guide
Features
Setting up your tripod
1Open the ip-lever leg locks on each leg.
Extend the leg sections from the top down
(thickest section rst) to reach the height you
want.
Note: Adjusting the thickest leg sections rst gives your
tripod more stability and support.
2Close the ip-lever leg locks to lock each leg at the
desired length.
Caution: Securing a leg lock incorrectly can cause a leg to
retract unexpectedly and could result in damage to the tripod
or equipment mounted on the tripod.
3Loosen the locking collar on the center column, then spread the
legs to the preset angle. Set the tripod on a rm surface. Tighten
the locking collar to stabilize your tripod.
4Adjust the height of the center column by loosening the
elevation locking knob, turning the elevation crank until the
center column is at the height you want, then tightening the
knob. Turn the locking knob clockwise to lock the center column
in place.
5Hold the quick-release plate locking lever open, then lift the
mounting plate to remove it.
6Align the bottom of your camera or camcorder with the 1/4"
mounting screw and indexing pin (if necessary) on the plate,
then secure your camera or camcorder to the plate with the
screw. The screw should be tight. The indexing pin retracts if it is
not required.
7Open the plate locking lever and slide the plate onto the tripod
head. Push the lever until it stops to secure the plate.
Using your tripod
1To adjust vertical tilt, loosen the vertical tilt lock knob, rotate the
plate up to 90 degrees, then tighten the knob.
2To adjust horizontal tilt, turn the horizontal tilt lock handle
counter-clockwise, tilt the tripod head, then tighten the handle.
3To pan, turn the pan locking knob counter-clockwise, pan the
tripod head, then tighten to lock in place or continue panning.
Note: For maximum stability, always make sure that your camera lens is
over a leg.
# Item
1 Quick-release plate
2 Leveling bubble
3 Pan locking knob
4 Elevation locking knob
5 Elevation crank
6 Quick-release plate
locking lever
7 Vertical tilt lock knob
8 Horizontal tilt lock
handle
9 Grip sponge
10 Locking collar
11 Flip-lever leg locks
12 Rubber feet
Description
Mount your camera to this plate, then
mount this plate to the tripod.
The quick-release plate is level when the
bubble is within the circle.
Locks the tripod head so that it will not
rotate horizontally.
Locks the center column in place.
Raises and lowers the center column.
Secures the quick-release plate to the
tripod.
Adjusts the vertical tilt up to 90 degrees.
Adjusts the horizontal tilt.
Grip the tripod comfortably.
Locks the tripod legs in place to provide
maximum stability and strength.
Lift to adjust leg height, then close to
lock.
Provide a secure, non-slip footing for
your tripod.