Dynex DX-TRPMN665 User manual

Center
column
locking
screw
V1 ENGLISH 14-0372
Storing your tripod
1Remove your camera.
2Loosen the center column locking screw. Lower the column as
far as it will go, then tighten the locking screw.
3Collapse the legs.
4Press the leg release buttons and push the legs in.
5Store the tripod in the carrying case.
Important safety instructions
• Make sure that all leg locks are correctly tightened and that the
legs are fully opened before use.
• Do not carry or transport your tripod with camera equipment
attached (for example, over your shoulder or cradled in your
arms).
• Do not expose your tripod to excessive heat or cold, or use near
any ame or re.
• Do not oil or grease any part of the tripod.
• Do not use any solvents or thinners to clean your tripod. Use
only a mild detergent and wipe dry with a soft, lint-free cloth.
• Do not exceed the load limit of this tripod.
Specications
• Maximum operating height : 66.5 in. (168.9 cm)
• Minimum operating height: 22.64 in. (57.5 cm)
• Folded height: 24.8 in. (63 cm)
• Net weight: 4.3 lbs (2 kg)
• Max operating load: 11 lbs (5 kg)
• Number of leg sections: 4
• Quick release thread: 1/4 in. (0.6 cm)
• Material: aluminum alloy
One-year limited warranty
Visit www.dynexproducts.com for details.
Contact Dynex:
For customer service, call 800-305-2204 (U.S. and Canada) or
01-800-926-3020 (Mexico)
www.dynexproducts.com
DYNEX is a registered trademark of BBY Solutions, Inc.
Registered in some countries.
Distributed by Best Buy Purchasing, LLC, 7601 Penn Ave South, Richeld, MN 55423 U.S.A.
©2014 BBY Solutions, Inc. All Rights Reserved.
QUICK SETUP GUIDE
DX-TRPMN665
66.5" Tripod-Monopod
Combo
Before using your new product, please read
these instructions to prevent any damage.
Using your tripod
1To adjust your camera to portrait position, loosen the vertical tilt
lock knob, rotate the plate up to 90°, then tighten the knob.
2To adjust horizontal tilt, turn the pan locking knob counter-
clockwise, tilt the tripod head as desired, then tighten the handle.
3To pan, turn the pan locking knob counter-clockwise, pan the
tripod head, then tighten the knob to lock in place.
Note: For maximum stability, always make sure that your camera lens is
over a leg.
4To adjust the vertical tilt, loosen the vertical tilt handle, then use
the handle to adjust the vertical position. Tighten the vertical tilt
handle.
Converting to a monopod
1Loosen the center column locking screw, and remove the center
column/monopod leg (with the pan head).
2With one hand, grab all the twist screw leg locks on the
monopod leg and twist them counterclockwise to loosen them.
3Extend the leg sections, starting with the thickest section, to the
height you want.
4Twist each leg lock clockwise to tighten it.
Caution: Incorrectly securing a leg lock can cause the monopod leg to
retract unexpectedly and could result in damage to the monopod or to
the attached camera or camcorder
Vertical tilt
lock knob
Rubber
foot
Twist
locking
screw
Monopod leg

Mounting plate
Quick-release plate
locking knob
Center column
locking screw
Package contents
• Tripod
• Carrying case
• Quick Setup Guide
Features
• 3-way pan head with slide quick release plate
• Smooth uid movement for cameras up to 11 lbs (5 kg)
• Center column converts to a monopod that extends
59.3 in. (150.6 cm)
• Independent legs spread with three angle adjustments
• Reversible tripod leg
# Item
1 Leveling bubble
2 Vertical tilt lock
knob
3 Vertical tilt lock
handle
4 Leg release button
5 Mounting plate
6 Quick-release plate
locking knob
7 Pan locking knob
8 Center column
locking screw
9 Center column/
monopod leg
10 Flip-lever leg locks
11 Rubber feet
Description
The quick release plate is level when the bubble
is in the center.
Adjusts vertical tilt up to 90 degrees.
Adjusts vertical tilt for head.
Lets you adjust the leg angle position
Holds your camera.
Secures the quick-release plate to the tripod.
Locks the tripod head so that it will not rotate
horizontally.
Locks the center column in place.
Provides quick height adjustment.
Locks the legs in place.
Provide a secure, non-slip footing for your tripod.
Setting up your tripod
1Open the ip-lever leg locks on each leg.
2Extend the leg sections from the top down (thickest section rst)
to reach the height you want.
3Close the ip-lever leg locks on each leg.
Caution: Incorrectly securing a leg lock can cause the tripod leg to
retract unexpectedly and could result in damage to the tripod or to the
attached camera or camcorder.
4Adjust the height of the center column by loosening the center
column locking screw, raising the center column to the height
you want, then tightening the locking screw.
5To set the angle position of the legs, press the leg release buttons
and lift the tripod leg.
6To remove the mounting plate, turn the quick-release plate
locking knob counter-clockwise to loosen it, then turn the
quick-release plate locking knob open, then lift the mounting
plate to remove it.
7Align the bottom of your camera or camcorder with the
1/4" mounting screw, then secure your camera or camcorder to
the plate with the screw. The screw should be tight.
8To attach the mounting plate to your tripod, loosen the
quick-release plate locking knob, then slide the plate onto the
tripod head. Tighten the quick-release plate locking knob.