E-FLITE CESSNA 182 370 User manual

Cessna 182 370 ARF
Assembly Manual
Cessna, 182 Skylane, (associated emblems and logos, and
body designs of vehicles) are either registered trademarks or
trademarks of Textron Innovations, Inc. in the USA and/or
other countries, used under license by Horizon Hobby.

2
Introduction
Thank you for purchasing the Cessna 182 370 ARF
(EFL2200), a vacuum-formed model of the full-scale Cessna
182 Skylane. The Cessna features a vacuum-formed fuselage
and wing, scale details, and quick final assembly time,
making this a great scale park flyer choice for smooth stable
flights.
We provide a 5.33:1 gearbox and a 10 x 7 propeller so
you can easily add our E-flite™ Park 370 Inrunner Brushless
Motor, 4100Kv for exceptional performance. For a direct
drive alternative, try the E-flite Park 400 Outrunner, 920Kv
motor.
Specifications
Wingspan: 38 in (965mm)
Length: 30 in (760mm)
Wing Area: 215 sq in (14 sq dm)
Weight w/o Battery: 13–13.5 oz (370–380 g)
Weight w/ Battery: 15.5–17 oz (440–480 g)
Table of Contents
Introduction ................................................................2
Specifications .............................................................2
Contents of Kit/Parts Layout .........................................3
Required Radio Equipment ...........................................4
Important Information About Motor Selection .................4
Sport Setup (stock gearbox) .........................................5
High Power Setup (stock gearbox)* ..............................5
Sport Outrunner Setup .................................................6
High Power Outrunner Setup* ......................................6
Optional Accessories ..................................................6
Required Tools and Adhesives ......................................7
Using the Manual .......................................................8
Warning ....................................................................8
Before Starting Assembly .............................................8
Note on Lithium Polymer Batteries .................................8
Warranty Information ..................................................9
Landing Gear Installation ...........................................10
Inrunner Motor Installation .........................................11
Outrunner Motor Installation .......................................14
Cowling Installation ..................................................16
Radio Installation ......................................................18
Wing and Stabilizer Installation .................................23
Battery Installation ....................................................26
Control Throws .........................................................27
Center of Gravity ......................................................28
Range Testing the Radio ............................................28
Preflight ...................................................................29
2005 Official AMA
National Model Aircraft Safety Code .................30

3
Large Replacement Parts:
EFL2201 Main Wing w/Ailerons
EFL2202 Fuselage w/Rudder & Cowl
EFL2203 Horizontal Tail Assembly
EFL2204 Cowl
EFL2205 Landing Gear w/Wheel Pants
EFL2206 Wing Struts
EFL2207 Landing Gear Covers
EFL2208 Fuselage Tail Fairing
Contents of Kit/Parts Layout
Small Replacement Parts
EFL2209 Pushrods
EFLA200 Micro Control Horns
EFLA201 Micro Pushrod Keepers
EFLA203 Micro Control Connectors
EFLA204 Micro Rubber Spinner
EFLA213 E-flite/JR/Horizon Decals
EFLM202 Pinion Gear, 12T 0.4 Module
EFLM216 Gearbox, 5.33:1 (v2)
EFLM217 Spur Gear, 64T w/Shaft
EFLP1070 10 x 7 Slow Flyer Prop (kit includes
only 1)

4
Required Radio Equipment
You will need a 4-channel transmitter, crystals, micro
receiver, and four sub-micro servos. You can choose to
purchase a complete radio system that includes all of these
items or if you are using an existing transmitter, just purchase
the other required equipment separately.
JRP14010** JR Sport 4-CH System, MD2 UL
(NOTE: Still need two additional servos)
Complete Radio System
Or Purchase Separately
JSP30610 6CH UL FM Receiver w/o Crystal,
Positive Shift (JR/AIRZ)
Or
JSP30615 6CH UL FM Receiver w/o Crystal,
Negative Shift (HRC/FUT)
JRPXFR** FM Receiver Crystal
EFLRS75 7.5 gram Sub-Micro Servo (4)
JSP98020 Y-Harness, Standard 6"
JSP98110 Servo Extension 6"
Important Information About Motor
Selection
We are recommending the E-flite™ Park 370 Brushless
Motor with 4100Kv (EFLM1000) or the Park 400 Outrunner
Brushless Motor, 920Kv.
The Park 370 Brushless Motor, 4100Kv provides more than
awsome power with a 1200–1320mAh 3-cell Li-Po battery
or park flyer power with a 2-cell Li-Po battery. Just use the
included 5.33:1 gearbox and 10x7 propeller.
It is extremely important to monitor gearbox wear and motor
temperature when using the 4100Kv motor. Lack of proper
throttle management using this motor and a 3-cell Li-Po
battery may result in damage to the motor, gearbox, ESC,
and battery. Adequate motor cooling is very important, so
make sure the motor is cooled properly in the cowl.
For a direct-drive Outrunner alternative, use the Park 400
Outrunner, 920Kv, which will also provide plenty of power
without worrying about gearboxes.

5
Sport Setup (stock gearbox)
EFLM1000 Park 370 Inrunner Brushless Motor,
4100 Kv
EFLA311B 20-Amp Brushless ESC (V2)
EFLP1070 10 x 7 Slow Flyer Prop (2) - keep
extras on hand
THP13202SPL 1320mAh 2-Cell 7.4V Li-Po, 16GA
WSD1300 Ultra Plug, Male/Female Set
EFLC3005 Celectra 1-3 Cell Li-Po Charger
Use with included 10 x 7 prop, 5.33:1 gearbox, and 12T
(0.4 module) pinion. This is a sport flyer setup for smooth
and stable flights.
High Power Setup (stock gearbox)*
EFLM1000 Park 370 Inrunner Brushless Motor,
4100 Kv
EFLA311B 20-Amp Brushless ESC (V2)
EFLP1070 10 x 7 Slow Flyer Prop (2) - keep extras
on hand
THP13203SPL 1320mAh 3-Cell 11.1V Li-Po, 16GA
WSD1300 Ultra Plug, Male/Female Set
EFLC3005 Celectra 1-3 Cell Li-Po Charger
* Use with included 10 x 7 prop, 5.33:1 gearbox, and
12T (0.4 module) pinion. Proper throttle management
is required when using high performance setups.
Using this setup with 3 cells will give you plenty of
power for zippy flights.

6
High Power Outrunner Setup*
EFLM1305 Park 400 Outrunner Motor, 920 Kv
EFLA311B 20-Amp Brushless ESC (V2)
EFLM1915 Outrunner Stick Mount
EFLP1070 10 x 7 Slow Flyer Prop (2)
THP13203SPL 1320mAh 3-Cell 11.1V Li-Po, 16GA
WSD1300 Ultra Plug, Male/Female Set
EFLC3005 Celectra 1–3 Cell Li-Po Charger
* Proper throttle management is required when using high
performance setups. Using this setup with 3 cells will give
you plenty of power for zippy flights.
Optional Accessories
EFLA110 Power Meter
EFLA212 Gear Puller: 1mm–5mm Shaft
Sport Outrunner Setup
EFLM1305 Park 400 Outrunner Motor, 920 Kv
EFLA311B 20-Amp Brushless ESC (V2)
EFLM1915 Outrunner Stick Mount
EFLP1070 10 x 7 Slow Flyer Prop (2)
THP13202SPL 1320mAh 2-Cell 7.4V Li-Po, 16GA
WSD1300 Ultra Plug, Male/Female Set
EFLC3005 Celectra 1–3 Cell Li-Po Charger
This is a sport flyer setup for smooth and stable flights.

7
Tools & Equipment
EFLA250 Park Flyer Tool Assortment, 5pc
Or Purchase Separately
EFLA257 Screwdriver, #0 Phillips (or included with
EFLA250)
EFLA255 Nut Driver, 5.5mm (or included with
EFLA250)
EFLA251 Hex Wrench: 3/32” (or included with
EFLA250)
Hobby Knife
Hot Glue Gun
Square
Ruler
Felt Tip Pen
Wax Paper
String
Adhesives
EFLA208 Thick Foam CA/Activator Pack
Or Purchase Separately
EFLA206 Foam Compatible Thick CA (included
with EFLA208)
EFLA207 Foam Compatible Activator (included
with EFLA208)
EFLA209 Foam Compatible Medium CA
Thread Lock (for mounting motor to gearbox)
Low Temperature Hot Glue
Required Tools and Adhesives

8
Using the Manual
This manual is divided into sections to help make assembly
easier to understand, and to provide breaks between each
major section.
Remember to take your time and follow the directions.
Warning
An RC aircraft is not a toy! If misused, it can cause serious
bodily harm and damage to property. Fly only in open
areas, preferably at AMA (Academy of Model Aeronautics)
approved flying sites, following all instructions included with
your radio.
Keep loose items that can get entangled in the propeller
away from the prop, included loose clothing, or other objects
such as pencils and screwdrivers. Especially keep your hands
away from the propeller.
Before Starting Assembly
Before beginning the assembly of your Cessna 182, remove
each part from its bag for inspection. Closely inspect the
fuselage, wing panels, rudder and stabilizer for damage. If
you find any damaged or missing parts, contact the place of
purchase.
Note on Lithium Polymer Batteries
Lithium Polymer batteries are significantly
more volatile than alkaline or Ni-Cd/Ni-
MH batteries used in RC applications. All
manufacturer’s instructions and warnings
must be followed closely. Mishandling of Li-Po
batteries can result in fire. Always follow the
manufacturer's instructions when disposing of
Lithium Polymer batteries.

9
Once assembly of the model has been started, you must
contact Horizon Hobby, Inc. directly regarding any warranty
question that you have. Please do not contact your local
hobby store regarding warranty issues, even if that is where
you purchased it. This will enable Horizon to better answer
your questions and provide service in the event that you may
need any assistance.
If the buyer or user is not prepared to accept the liability
associated with the use of this product, they are advised to
return this kit immediately in new and unused condition to
the place of purchase.
For any additional questions please contact:
Horizon Hobby Product Support
4105 Fieldstone Road
Champaign, Illinois 61822
[phone]
www.horizonhobby.com
Warranty Information
Horizon Hobby, Inc. guarantees this kit to be free from
defects in both material and workmanship at the date of
purchase. This warranty does not cover any parts damaged
by use or modification. In no case shall Horizon Hobby’s
liability exceed the original cost of the purchased kit. Further,
Horizon Hobby reserves the right to change or modify this
warranty without notice.
In that Horizon Hobby has no control over the final assembly
or material used for the final assembly, no liability shall be
assumed nor accepted for any damage of or caused by the
final user-assembled product. By the act of using the product,
the user accepts all resulting liability.

10
Landing Gear Installation
Required Parts
Fuselage
Landing gear
Landing gear fairing (2)
10mm x 136mm tape (2)
 1. Locate the landing gear. Press the gear into the
slot in the bottom of the fuselage.
Note: The landing gear is designed for smooth
or paved surfaces. It is not recommended for
grass surfaces.
 2. Use the 10mm x 136mm tape to attach the
landing gear fairings to the landing gear.

11
Inrunner Motor Installation
Required Parts
Airframe 5.33:1 (64T spur) gearbox
Brushless motor Brushless speed control
2mm x 8mm screw (2)
12T pinion gear, 0.4 module x 6mm
Required Tools and Adhesives
Phillips screwdriver (small) Hobby knife
Hook & loop
Important Information about Your Brushless ESC
Make sure your ESC brake is programmed to Off. Also,
be sure to use an ESC with the proper 9V cutoff when
using 3-Cell Li-Po packs, or 6V cutoff when using 2-cell
Li-Po packs.
Note: This section covers the installation of an
Inrunner motor and gearbox. Skip to Page 12
for Outrunner Motor Installation.
 1. It may be necessary to attach motor adapters or
other accessories to your particular motor at this
time.
Note: Use the instructions provided with the
motor to install any accessories. Follow the
instructions provided with the gearbox for some
helpful hints for installing the motor. When
installing your motor into the E-flite™ gearbox,
it is very important that the gear mesh is set
correctly and is smooth with no binding. The
E-flite gearbox features adjustable slotted
mounting holes to ensure your gear mesh is
correct. Remember if the gear mesh is too loose
or too tight, it may strip the gears. To extend
the life of your gearbox, we also recommend
using a small amount of grease, such as lithium
grease, on the spur gear.
It is also very important to check to be sure the
propeller is balanced before installing onto the
shaft. An unbalanced propeller may strip the
gears. When installing the propeller, please be
sure not to over-tighten the 3mm locknut. The
use of the locknut will prevent the propeller from
coming loose.
Use the 12-tooth pinion we include with this
airplane on the motor.

12
 3. Slide the gearbox onto the motor stick. Use a
hobby knife to drill a hole through the plastic and
into the motor stick. Secure the gearbox using a
2mm x 8mm wood screw on the top and one or
even two in the side.
Hint: You may want to plug in the speed control
before installing the gearbox.
 2. Attach the motor to the gearbox using the screws
provided with the motor.

13
 4. Secure the speed control location using hook
and loop. Run the lead from the speed control to
the receiver. It may be necessary to use a servo
extension. Exact speed control location may vary
depending on the brand used and the center of
gravity. This photo shows the location in the front
of the fuse if you are using our E-flite™ 20-amp
Brushless ESC.

14
Outrunner Motor Installation
Required Parts
Airframe
Brushless motor Brushless speed control
Outrunner Mount (EFLM1915 - sold separately)
2mm x 8mm wood screw (2)
Required Tools and Adhesives
Phillips screwdriver (small) Hobby knife
Hook & loop
Important Information about Your Brushless ESC
Make sure your ESC brake is programmed to Off. Also,
be sure to use an ESC with the proper 9V cutoff when
using 3-Cell Li-Po packs, or 6V cutoff when using 2-cell
Li-Po packs.
Note: This section covers the installation of an
Outrunner. Skip back to Page 10 for Inrunner
Motor Installation.
 1. Attach the outrunner stick mount (EFLM1915 - sold
separately) to the outrunner motor at this time. Use
the hardware provided with your motor to attach it
to the mount using at minimum of two screws.
Note: It is also very important to check to be
sure the propeller is balanced before installing
onto the shaft.
 2. When using the E-Flite™ outrunner motor and
mount, you will need to shorten the motor mount
stick by 13/16" (20mm). Use a razor saw to cut
the motor mount stick.

15
 3. Slide the motor mount and motor onto the motor
stick. Use a hobby knife to drill a hole through
the plastic and into the motor stick. Secure the
gearbox using a 2mm x 8mm wood screw. We
suggest adding one or two additional screws to
the sides on the outrunner stick mount.
Hint: You may want to plug in the speed control
before installing the motor mount.
 4. Secure the speed control location using hook
and loop. Run the lead from the speed control to
the receiver. It may be necessary to use a servo
extension. Exact speed control location may vary
depending on the brand used and the center of
gravity. This photo shows the location in the front
of the fuse if you are using our E-flite™ 20-amp
Brushless ESC.

16
Note: If you have selected the outrunner motor
option, install the propeller adapter onto the
motor shaft.
Note: The propeller will have to be drilled out
using a 15/64" drill when using the outrunner
motor and propeller adapter.
Cowling Installation
Required Parts
Airframe Rubber spinner or propeller adapter
3mm locknut 3mm washer
10 x 7 propeller 2mm x 5mm screw (4)
Required Tools and Adhesives
Phillips screwdriver (small) Hobby knife
Hook & loop
 1. Slide the cowling onto the fuselage, then the
propeller. Make sure there is clearance between
the cowling and propeller. Drill four locations for
the cowling screws.

17
 2. Secure the cowling using four 2mm x 5mm
screws. Secure the propeller using the
3mm washer and 3mm locknut.
Note: Simply tighten the adapter when
using the outrunner and associated propeller
mounting hardware.
 3. Press the spinner into position (if using the
Inrunner and gearbox option).

18
Radio Installation
Required Parts
Fuselage
Wing
Micro control connector (5)
Control connector backplate (5)
2mm x 8mm screw (8)
Aileron servo cover (2)
3" linkage (2)
Y-harness, standard 6"
Servo extension 6"
Double-sided tape (2)
Required Tools and Adhesives
Phillips screwdriver (small)
Hobby knife
Hook & loop
String
Hot glue gun
 1. Attach a micro control connector to the servo arm
for the elevator. Use the connector backplate to
secure the connector.
 2. Plug the elevator servo into the receiver and
turn on the radio. Make sure the trim has been
centered, and then attach the servo arm to the
servo as shown.

19
 3. Repeat Steps 1 and 2 for the rudder servo, but
install two connectors instead of one.
 4. Use hot glue to install the rudder and elevator
servos into the fuselage.
 5. Pass the pushrods for the rudder and nose
wheel through the connectors. With the radio
on, physically center the rudder and nose wheel.
Tighten the screw in the connector to secure the
pushrod wires.
Note: Use the rudder trim for trimming flight
conditions. Do not use the trim if your plane
does not taxi straight. Loosen the screw in the
connector and change the position of the wire
to correct any taxi problems.

20
 6. Attach the receiver to the side of the fuselage
using a piece of hook and loop. Plug the servo
leads into the receiver at this time. Route the
antenna wire through the fuselage.
 7. Attach a micro control connector to the servo arm
for the aileron. Use the connector backplate to
secure the connector. Plug the aileron servo into
the receiver and turn on the radio. Make sure the
trim has been centered, and then attach the servo
arm to the servo as shown.