Eagle Eye PV922 User manual

PV922 | ENGLISH USER MANUAL
1
USER MANUAL
Please read this user manual carefully and thoroughly before any attemptto Install
and operate this product and retain it for your future reference.

PV922 | ENGLISH USER MANUAL
2
CATALOG
INTRODUCTION ……………………….…….………………………………….3
WARNING ……………..……………..…..……………………………………… 4
OVERVIEW………...………………………………………………………...…5-7
Main device………………………..……………..…………………………...…….5
Remote Controller…………………………………………………………………..6
Power charger………………………………………………………………………7
BASIC OPERATION ………………….…...…………………………….….. 8-13
Battery Installation……………………...…………………………………..………8
Connect with the camera …………………………………………... ……..……….9
Start recording………………………………………………………....…………..10
Connect with TV…………………..………………………………........…………11
Connect with computer………….………………………….…………...……..12-13
FUNCTION MODES……………………………………………………….14-20
Booting picture………………………………………….……...…………………14
Record Interface………………..………………………………………………….14
Record interface…………………………………...……………………….…….15
Multi-media folders…………………………………….………...…………16-20
Function setting…………………..…..…………….……………...……21-39
ACCESSORIES……………………………………...……………………….40-41
PARAMETERS…………………………………………………………………..42

PV922 | ENGLISH USER MANUAL
3
INTRODUCTION
Thank you for purchasing PV922 which has the unique, ultra-small and delicate design. It
can be used in many recording situations. PV922 rings more convenience, safety and funs
to your daily life.
Approval Information:
All our products meet the requirements of approval FCC or CE, and are granted the
FCC or CE certification. They are authorized to bear FCC or CE mark.
FCC:
This product has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
CE:
This product complies with standards including Low Voltage Device Directive
73/23/EEC; EMC Directive 89/336/EEC and R&TTE Directive1999/5/EC. It passed the
subject tests by the authority concerned and is authorized to bear CE mark.
OVERVIEW
Along with the improvement of people’s living standard and the development of
picture compression and memory technology, the digital video memory has been a part of
our daily life. PV922 a high-tech product, just meets a plenty of needs of people and
market. It possesses a series of advanced functions including digital photography, voice
memory, sound trigger recording, high speed USB data transferring and USB charging.
EU Environmental Protection
Waste electrical products should not be disposed of with
household waste. Please recycle where facilities exist.
Check with your Local Authority or retailer for recycling
advice.

PV922 | ENGLISH USER MANUAL
4
WARNING
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
Attention
The electromagnetic fields at the specific frequencies may influence the picture of
the recorder. Be sure to read the following before using the recorder and the mini
camera.
The requirements of receiving wireless signal:
The frequency of wireless signal transmit by this product is 2.4GHz FM, maybe
interfere by other electronics, such as high-voltage, signal transmitting beacon,
wirelss remote control and wirelsss alarm. Please keep away from them as possible.
And please try other channel if signal in monitor status is not well.
Trial recording
Before you record one-time events, you may want to make a trial recording to
make sure that the recorder and the camera are working correctly.
Notes on image data compatibility
Playback of moving images recorded with your recorder on other equipment and
playback of moving images recorded or edited with other equipment on your
recorded are not guaranteed.
Do not shake or strike the recorder
In addition to malfunctions and inability to record moving images, this may render
the SD card unusable of image data breakdown, damage or loss may occur.
LCD screen and mini camera
Be careful when placing the camera near a window or outdoors. Exposing the
LCD screen or the lens of camera to direct sunlight for long period may cause
malfunctions.
Back up recommendation
To avoid the potential risk of data loss always copy data to a disk.
Protect your hearing.
Hear by high volume earphone will damage your hearing, we suggest you use a suitable
volume during listening.

PV922 | ENGLISH USER MANUAL
5
*Overview
Main Device
1.Function knob 9. Select /Back
2.Video Input 10.Play/Record/Confirm
3.AV Output/Earphone jack 11.UP
4.Power switch/Delete/Capture 12.USB jack
5. LED light 13.Micro-SD slot
6. Speaker 14.Down
7. Channel switch 15.Volume
8.TFT LCD 16.Microphone

PV922 | ENGLISH USER MANUAL
6
Back side：
1, Toggle switch: use to change between 6.0 and 6.5 audio system.
2. Remote control match button: use to match new remote control’s frequency, the match
button and start recording button on remote control should be pressed on the same time
during matching.
Remote control
Start recording
Stop recording
Notice:
1, When you use remote control to record, press the start recording button will power on the DVR and
start to record video, but LCD is still in turn off mode.
2, Press stop recording button will stop recording and power off DVR main set.
3, During remote control mode, the all buttons on DVR main set are unavailable to operate. After you
stop recording and power off DVR by remote control, the buttons on DVR will be available to operate.
4, The working range of remote control is 10 meters under unblock situation.

PV922 | ENGLISH USER MANUAL
7
BASIC OPERATION
Power Charger：
Please chage the battery before first using.
1. Connect charger’s USB pins into PV922’s multifunctional USB port.
2. Connect the charger with standard AC power socket.
3. When the battery is full charged,（ico on LCD will not flash any more），you
can pull out the charger from power socket.
LED lights：
1, During PV922 is in charging mode, the red LED light will be always turn on.
2, After PV922 full charged, red LED light will be turn off and blue light start turn on.
Notice:
If you want to charge power when the DVR is recording, it only can works with wireless camera.
Otherwise, the wire camera has no enough power, may cause bad recording effect.

PV922 | ENGLISH USER MANUAL
8
Install the battery：
Pull down the cover according the picture shows below, open the battery back cover.
Shown as Fig below：
The 4 golden female pins of the battery should be full touched with the male pins in the
battery house.
Close the cover after install the battery well.
Battery using time information form：
Capability
Charging time
Standby time
Playing time
Recording time
1300mAh
Approx ：4
hours
Approx ：2
hours and 19
minutes
Approx ：4
hours
Approx one
hour and 43
minutes

PV922 | ENGLISH USER MANUAL
9
Connect With the Camera：
Picture 1 ： Wireless camera receiving
1. Install the camera to the location you want to monitor, choose the bset channel, and
then connect with the power source.
2. Switch the Function knob on main set to wireless receiving mode, press channel
change button to receive signal which sent from wireless camera.
3. In wireless mode, press menu button can choose manual operation or auto operation.
*Choose manual, press to save, and press menu to back, use to change
channel by hand.
* Choose Auto, press to save, and press menu to back, the main set will change
channel per 5 seconds.
The meanings of wireless iterface ico:
Wireless receiving situation, CH1：current receiving channel，AUTO: channel
auto change mode. 自动切换时间为 5秒切换一个频道

PV922 | ENGLISH USER MANUAL
10
Note：
The frequency
of wireless
receiving
Channel
Min
Typical
value
Max
Unit
CH1
2413.75
2414
2414.25
MHz
CH2
2431.75
2432
2432.25
MHz
CH3
2449.75
2450
2450.25
MHz
CH4
2467.75
2468
2468.25
MHz
Compatible with both 6.0 and 6.5 audio system.
Picture 2 ： Wire camera installation
1. Pullthe camera’s output port into main set’s AV IN port.
2. Power on the main set, switch to wire camera recording mode, the LCD screen will
show the picture caught by camera.

PV922 | ENGLISH USER MANUAL
11
Start Recording
①Power on the main set, match the frequency of main set and camera in wireless
recording mode, or check the camera connection in wire recording mode.
②Switch the function knob to function setting, to set recording mode.
Press button to start recording, top left corner on screen will show
recording ico.
③Press button to stop recording, recording ico will disappear.
④In preview mode, press button can take photo.
Once-Operation recording mode: Continuous recording and storage the video per 30
minutes;
Motion recording mode：It will continuous recording if movement sensed, 30 minutes
longest for each part, if movement is not sensed, recording
will stop after 15 Secs.
Timing recording mode：Start recording according to the time you setted, 30 minutes of
each video file.
Audio recording mode: The audio file will not storage in partial.
Attention：
The mein unit has the vibrate notice while low power and no video signal.
1.While the camera did not connect with the main unit correctly, the main unit will
vibrate because of no signal, please check the connection carefully.
2.While the power is not enough, the main unit will continuous vibrate 3 times, at
the same time stop recording.

PV922 | ENGLISH USER MANUAL
12
Connect with TV：
1. Connect main set with TV by RCAAV OUT line. As follow:
2. Power on the main set and TV, switch function knob on main set to function setting,
choose video output, and press confirm button, choose PAL or NTSC TV system, then
TV will show what on main set screen.
3. Switch the function knob to multi-medi, use and to select what you
want to play, pess to start playing.

PV922 | ENGLISH USER MANUAL
13
Connect with Computer：
①Connect the USB and MINI USB with computer and the main unit separately.
②After connect with computer,PV922 will display “ USB Connect”, recharge
indicator always on.
Note:
Connect with computer at power on states, can not operate as it is External Hard Drive.
Connect with computer at power off states, can do any operation as it is recharging.

PV922 | ENGLISH USER MANUAL
14
③ Open “my computer” to check if there has the removable hard disk, called
“NO_NAME” .
Picture details：
④Open the video files in the folders.
⑤Check the video files in the folders, and play it by the default media player in your
computer.
Attention：
Connect the main unit with PC under power off state，it is power charge mode, red
indicator flash at the same time, files in the storage can not be read. Connect the main
unit under power on state, the computer will read the files in the storage automatically
and power charging at the same time.

PV922 | ENGLISH USER MANUAL
15
*Function Modes
Booting Picture：
Record Interface：
Recording Mode：
⑴Recording symbol ⑺Battery capacity
⑵Current time ⑻Current time
⑶Video files ⑼Picture quality of recording
⑷Record time ⑽Record content
⑸Card icon( if memory card available) ⑾Circular record
⑹Available memory

PV922 | ENGLISH USER MANUAL
16
Multi-media folders：
Use or to select the folder and press confirm and enter.
Video folder：
As picture above：”20091012” means the folder that built in 12th Oct of 2009. One folder
for every day.
Video files：
As picture above：”223118.AVI” means the video file that built in 22:31:18 ,30 minutes
in a file of each part.

PV922 | ENGLISH USER MANUAL
17
Video play：
Use and select the video for playing and press start play or
pause.
Use and select forward/backward mode and press to play or
pause.
Notice：Here has 4 speed level of forward and backward.×2/×4/×8/×20

PV922 | ENGLISH USER MANUAL
18
Audio folders：
Use or to select the folder and press confirm and enter.
For the audio files that already exist，please use and to select the
content and press confirm and playing.
Playing interface:
Press and button to play other audio content.

PV922 | ENGLISH USER MANUAL
19
Picture folders：
Press or to select picture folder, press confirm and enter.
Press or to choose the picture, press playing it.
Picture Display：
Press or to browse other pictures.
Note：JPG format picture, 640×480 resolution.

PV922 | ENGLISH USER MANUAL
20
Delete files：
Enter video folder，choose the file that you want to delete, short press “Power” button till
the delete menu appear.
Press or to choose “ALL/CURRENT”. Press confirm or choose
“ Cancel” menu quit operation.
Use or to choose “YES” or “NO”.Press confirm delete or cancel this
operation.
ALL：Delete all data
CURRENT：Delete the file that selectd
CANCEL：Cancel the delete operation