Easee Home Wallbox User manual

Installation Instructions
Quick Guide
Authorized
personnel
only

Download your language
In order to avoid unnecessary waste of resources by printing the Quick
Guide in dierent languages, we have chosen to include only English and
make other languages available on our website.
You can download this Quick Guide in other languages here1
1We cannot guarantee that all languages are available at this time.
www.easee.no/manuals
THIS DOCUMENT CONTAINS INFORMATION THAT IS
SUBJECT TO CHANGE WITHOUT NOTICE.
The latest version of this publication can be
downloaded at easee.no
No part of this publication may be reproduced or
transmitted in any form or by any means, electronic
or mechanical, including, but not limited to, copying,
recording, retrieving data, or computer networks
without the written permission of Easee AS.
Easee and all other Easee product names and
slogans are trademarks or registered trademarks of
Easee AS. Easee products can be protected by one
or more patents.
All other products and services mentioned may be
trademarks or service marks of their respective
owners.
September 2019 - Version 2.04 / © 2018-2019 by
Easee AS. All rights reserved.
Join Easee Owners Club on facebook,
and get valuable product insight rst!
Follow us on facebook and Instagram.

Open the charging robot
1
1. Bend down the lower part of the rubber cover and insert the two ends of
the included tool into the two openings at the bottom of the front cover.
2. Pull down until it comes loose.
3. Grasp the Type2 connector and push upwards with good force until the
Chargeberry disconnects.
2
1
3
1

130-140 cm
Recommended installation height
Mounting the backplate
2
1. The backplate is mounted on the wall using the 4 wall-screws supplied in
the installation kit. Use appropriate wall plugs for dierent types of walls.
NB! If you have multiple backplates, now would be a good time to mount
them as well!
1
1
1
1
1

Prepare the backplate
3
1. Fit the sealing plug on the cable before connecting in the backplate.
2. Secure the sheath of the cable by using the supplied strain relief.
3. Close all holes that are not used for cable entry with the blind sealing
plugs supplied.
1
2
1 2
3
33
3

Connect the backplate
4
1. All cable cores must be stripped back allowing 12mm exposed conductor.
2. For parallel connection, each termination port is used as connection point.
3. Tighten the screws with a torque of 5Nm.
NB! Terminations should be visually and mechanically inspected before
mounting the electronics.
3-phase TN
TN
IT
IT
3-phase
1-phase
1-phase
PE
PE
PE
PE
N
L1
N
L1
L1
L2
L2
L1
L2
L3
-
-
L3
-
-
-
3
1
2

Plug in the electronics
5
1. Match up the tabs on the Chargeberry with the slots in the backplate.
2. When the Chargeberry has reached the bottom, push it down with good
force until you hear a click!
NB! When installing several charging robots, you must use the same
chargeberry to program all the back plates that are connected to the same
fuse / cable - so please wait to plug in the remaining ones!
Click!
2
1

Start the conguration
6
Wi-Fi
Easee-Exx...
192.168.4.1
1
4
7
2
5
8
0
3
6
9
1. To start the conguration of the chargring robot(s), you must use a
smartphone and connect to the WiFi network on the charger you want to
be the main unit. This is done by rst holding the touch button until
the light strip turns green and you hear a conrmation tone.
2. Select the Wi-Fi network that begins with ”Easee...”
3. Open your browser and enter 192.168.4.1 in the address eld.
4. Log in with the PIN code located on the front of the chargeberry.
132
4

Enter installation details
7
1. Enter installation details and follow the on-screen instructions.
2. Press on the screen for more information.
NB! For several charging robots connected to the same fuse, all the back
plates must be programmed with the same chargeberry in order for load-
balancing to work!
Click!

Lock the electronics
8
Lock the Chargeberry with the included padlock. Locking the electronics
adds an extra level of security. (Optional)
1
1

Mount the front cover
9
1. Hang the front cover at the top of the backplate and let it fall into place.
2. Then press the bottom of the front cover until you hear a click!
3. Bend the lower part of the rubber cover down.
4. Screw in the locking screw at the bottom of the box to secure.
The charging robot is now ready for use, enjoy!
1
Click!
1
4
2
3

Powering your freedom
Easee AS
Professor Olav Hanssens vei 7A
4021 Stavanger, Norway