Eastwood Elite 55132 User manual

4' X 4'CNC PLASMA TABLE WITH
CNC CUT 60 PLASMA CUTTER
UNCRATING AND ASSEMBLY INSTRUCTIONS
Item # 55132
INCLUDES
Verify crate contents. Contact Eastwood if any parts are missing or damaged.
COMPONENTS
CNC Plasma Table Main Assembly [A]
Table Legs [B]
Height Adjustment Feet [C]
Plasma Cutter Shelf Bottom [D]
Plasma Cutter Shelf Sides [E]
Table Slats [F]
Accessory Box [G]
Eastwood CNC Cut 60 CNC Plasma Cutter Box [H]
Eastwood Instruction Manual [J]
EE
BB
BB
DD
JJGG
BB
BB
HH
AA
CC
FF

2Eastwood Technical Assistance: 800.343.9353 >> [e-mail]
READ INSTRUCTIONS
• Thoroughly read and understand these product instructions before uncrating and assembly. Failure to understand and follow these
instructions can result in serious injury or death.
• Make sure all uncrating and assembly participants have read and understand this manual.
• Keep these product instructions for future reference.
PINCH AND CRUSH HAZARD!
• The Eastwood Elite 4 x 4 Plasma Table is a heavy assembly 974 lbs. [442kg.] which can cause serious injuries if allowed to drop.
The use of a forklift, crane, hoist or similar mechanical lifting equipment capable of lifting a minimum of 1000lbs [454kg.] is required.
Lifting straps or fork extensions rated for a minimum of 1000lbs [454kg.] are required (not included).
• Obtaining the assistance of a capable helper during assembly is strongly recommended.
• Avoid pinching hands while handling parts and during assembly. The use of thick, well-fitting work gloves is strongly recommended.
• The wearing of approved safety shoes is strongly recommended when uncrating and assembling.
• DO NOT lift from the table gantry or gantry mounts. Doing so will result in damage to the table gantry.
• Only lift with forklift or sling from under the table and spread the load as wide as possible.
DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury.
WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
NOTICE is used to address practices not related to personal injury.
SAFETY INFORMATION
The following explanations are displayed in this manual, on the labeling, and on all other information provided with this product:

To order parts and supplies: 800.343.9353 >> eastwood.com 3
UNCRATING AND ASSEMBLY
• Remove all screws holding the exterior wooden panels to the steel
crate frame. Remove the wooden panels (FIG 1).
• Unscrew all four Table Legs from the frame and set aside for
assembly. Remove the four Height Adjustment Feet from water
table and install into the legs.
• Unbolt the cross beams and remove (FIG 1).
• Remove all remaining components from the water table: Plasma
cutter rack components, plasma cutter box, slats, hardware box.
• Cut the steel crate frame off at the base. Carefully lift it off and set
it aside (FIG 2).
• Lifting of the table is ideally done with long straps and a crane, or
forklift with fork extensions.
PINCH AND CRUSH HAZARD!
DO NOT utilize a forklift with short forks to lift the
table. The minimum recommended fork length is 6ft
[1.85m]. If the table tips off the forks it could result in
serious bodily injury and property damage.
DO NOT lift from the table gantry or gantry mounts.
Doing so will result in damage to the table gantry.
• Lift one side of the plasma table at a time and set it on cribbing so
the bottom side can be accessed (FIG 3).
• Now that it is elevated off the crate, pass straps underneath or
carefully slide the extended length forks underneath. Be conscious
of the drain valve stud and plasma rack mounting provisions, as
they could be damaged by forks (FIG 4).
FIG. 1FIG. 1
FIG. 2FIG. 2
FIG. 3FIG. 3
FIG. 4FIG. 4
CrossCross
BeamsBeams
✓
✓
Drain ValveDrain Valve
✓
PlasmaPlasma
Rack MountsRack Mounts
✓
✓

• Lift the plasma table up and remove the crate base from underneath.
Fasten the legs with leveling feet using the included M10 Socket Cap
Screws and tighten to 22 foot-pounds (30 Nm).
• Install the ball drain valve and utilize the included PTFE tape on the
threads to ensure it does not leak.
• Assemble the plasma cutter rack sides to the base with the included
M5x10 Round Cap Screws and Nuts. The base sets inside of the
sides (FIG 5).
• Fasten the plasma cutter rack assembly to the mounting flanges on
the table bottom with the included M8x16 Socket Cap Screws and
Nuts. Tighten to 20 foot-pounds (28 Nm). The sides set inside of the
mounting flanges (FIG 6).
• Unmount the base of the Control Panel Mount and remount it 180°
facing outward for operation.
• Install the included slats. Use of a mallet or hammer may be
necessary to fully seat them.
• Continue to Page 9 of the included instruction manual for further
setup and operation.
PINCH AND CRUSH HAZARD!
The Eastwood Elite 4 x 4 Plasma Table is a heavy
assembly 974 lbs. [442kg.] which can cause serious
injuries if allowed to drop. The use of a forklift, crane,
hoist or similar mechanical lifting equipment capable
of lifting a minimum of 1000lbs [454kg.] is required.
Lifting straps or fork extensions rated for a minimum
of 1000lbs [454kg.] are required (not included).
FIG. 5FIG. 5
FIG. 6FIG. 6
© Copyright 2022 Eastwood Automotive Group LLC 6/22 Instruction item #55132QUNCRATING Rev 1
If you have any questions about the use of this product, please contact
The Eastwood Technical Assistance Service Department: 800.343.9353 >> email: [e-mail]
PDF version of this manual is available at eastwood.com
The Eastwood Company 263 Shoemaker Road, Pottstown, PA 19464, USA 800.343.9353 eastwood.com
BaseBase
SidesSides
✓
✓
SidesSides
MountMount MountMount