Eastwood 21320 User manual

ROD FORMING TOOL
INSTRUCTIONS
Item #21320

2Eastwood Technical Assistance: 800.343.9353 >> [e-mail]
The EASTWOOD ROD FORMING TOOL is a high quality, industrial style tool capable of generating a
powerful leveraged force to create 180° or greater repeatable bends in mild steel and aluminum rods
up to 3/8” diameter and flat stock up to 1/2” wide and 3/16” thick.
CONTENTS
(1) Pin Base (Center Pin = 0.38” Diameter/0.19” Radius) [A]
(1) Forming Handle [B]
(1) 1.5” Diameter/0.75” Radius Die [C]
(1) 1.25” Diameter/0.63” Radius Die [D]
(1) 1” Diameter/0.5” Radius Die [E]
(1) 0.75” Diameter/0.38” Radius Die [F]
(1) 0.5” Diameter/0.25” Radius Die [G]
SPECIFICATIONS
Maximum Round Stock Diameter: 3/8”
Maximum Flat Stock Material Width: 1/2”
Maximum Flat Stock Material Thickness: 3/16” for 1/2” wide mild steel or 1/4” for 1/4” wide mild steel
Maximum Handle Length: 12”
DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury.
WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION used with the safety alert symbol, indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
NOTICE is used to address practices not related to personal injury.
SAFETY INFORMATION
The following explanations are displayed in this manual, on the labeling, and on all other information
provided with this product:
Hole
Stop Pin Center Pin
B
Drive Pin
G F E D C
✓
✓
✓
✓
✓
A

To order parts and supplies: 800.343.9353 >> eastwood.com 3
READ INSTRUCTIONS
• Thoroughly read and understand this manual before using.
• Save for future reference.
INJURY HAZARD!
• This tool has leveraged rotating components that generate greatly amplified
crushing and bending forces which can quickly cause severe injury! Keep
fingers and hands away from moving parts when operating.
• High external torque loads are placed on the Rod Forming Tool during
operation. The tool cannot be operated without adequate support or severe
personal injury or property damage can occur if it should suddenly become
dislodged or moves while in use. Before beginning ANY work with this tool, it
is absolutely necessary that it be securely clamped in a well-anchored vice.
• Strenuous physical force may need to be applied to the Rod Forming Tool
during use. Failure to ensure proper footing can quickly result in a fall which
could inflict serious personal injury or property damage. Always work in a
clean, uncluttered environment.
• Be sure there is sufficient working room around the tool to allow for safe
handling of various lengths of rod or tubing.
• The Eastwood Rod Forming Tool is equipped with a specifically designed
Handle length for sufficient bending force. DO NOT add pipe, bars or any
other devices which would add additional length to the Handle to increase
bending force. This will exceed the design limits of the tool and can result
in serious injury and/or component failure.
CUT HAZARD!
• Handling sharp metal can cause serious cuts. Wear thick, well-fitting work
gloves to prevent cuts from handling sharp metal.
EYE INJURY HAZARD!
• Pieces of mill scale, rust and other debris may be ejected from the work-
piece during operation. Wear ANSI approved eye protection while operating.
• Excessive resistance while operating could indicate a defect with the
workpiece material or broken or damaged Rod Forming Tool components.
To avoid injury, stop work immediately and inspect workpiece material for
nicks, dents, welds, excessive scale or remaining coatings. Clean or repair
as necessary or discard and begin with a new piece. Also, inspect Rod
Forming Tool components for looseness or damage.

4Eastwood Technical Assistance: 800.343.9353 >> [e-mail]
SET-UP
MOUNTING BENDER IN VICE
• Open vice jaws (not included) to
2-1/2” Place the stepped section
of the Pin Base [A] into the vice
with the side flanges resting on top
of the vice jaws (FIG 1).
• Close vice jaws and tighten
securely.
• The Eastwood Rod Forming Tool
is now ready for use.
Strenuous external torque loads are placed on the Rod Forming Tool during
operation. The tool cannot be operated without adequate support or severe
personal injury or property damage can occur if it should suddenly become
dislodged or moves while in use. Before beginning ANY work with this tool,
it is absolutely necessary that it be securely mounted in a solid, level, well
supported vice capable of withstanding the torque and side loads this tool
is subjected to during use.
The Eastwood Rod Forming Tool can present a hand/finger pinch hazard and
cause potentially serious injuries if dropped on feet. Avoid pinching hands
while operating and wear thick, well-fitting work gloves to prevent cuts from
handling sharp metal. The use of safety shoes is strongly recommended.
Make sure sufficient clearance is available around the vice area to allow a full
swing of the Rod Former Handle.
FIG. 1

To order parts and supplies: 800.343.9353 >> eastwood.com 5
BENDER OPERATION
• Select the Die size to produce the
desired bend radius and slip it
down over the Center Pin.
NOTE: The Center Pin may be
used without a Die to create a
3/16” radius bend (FIG 1).
• Attach the Forming Handle [B] by
sliding the hole in the end over the
Center Pin (FIG 2).
• Place material to be formed
between the Stop Pin and the
Die (FIG 2).
• Begin to apply pressure with the
Drive Pin of the Forming Handle
[B] to the side of the material in
the direction of the bend (FIG 3).
• Continue to create the desired
bend. Use a protractor (not
included) to measure the
planned angle.
• As the desired bend is achieved,
check shape and angle and adjust
if needed (FIGS 3, 4).
• Re-position or remove and switch
position of workpiece to make
additional bends (FIG 5).
NOTE: At this point, the basic operat-
ing instructions have been described
and practice using the Eastwood Rod
Forming Tool, on scrap material, is highly
recommended. As with many metal
working tools, a period of “trial and
error” is needed to achieve a degree of
proficiency in their use. Remember, a
little time and material used at this step
will avoid disappointing results on an
actual project.
FIG. 2
FIG. 3
FIG. 4
FIG. 5
Push Handle
✓
Drive
Pin

6Eastwood Technical Assistance: 800.343.9353 >> [e-mail]
STORAGE
• Apply a thin film of light oil or rust-preventive to all bare steel areas.
• Store in a clean, dust-free, dry, dampness free area preferably covered with plastic sheeting.
MAINTENANCE
NOTE: Maintenance should be performed before each use.
• Clean dirt and debris from all pivot points.
• Check tightness of all hardware.
• Check operation for binding. Lubricate moving parts periodically with medium bodied
chassis grease.

To order parts and supplies: 800.343.9353 >> eastwood.com 7
NOTES

© Copyright 2017 Easthill Group, Inc. 4/17 Instruction item #21320Q Rev 1
If you have any questions about the use of this product, please contact
The Eastwood Technical Assistance Service Department: 800.343.9353 >> email: [e-mail]
PDF version of this manual is available online >> eastwood.com/21320manual
The Eastwood Company 263 Shoemaker Road, Pottstown, PA 19464, USA
US and Canada: 800.343.9353 Outside US: 610.718.8335
Fax: [phone] eastwood.com
OPTIONAL ITEMS
#51088 Shrinker/Stretcher Set
#13475 Eastwood Electric Metal Shears
#11797 Throatless Shear
#14042 Versa Bend Sheet Metal Brake
#20254 Eastwood 24” Slip Roll
#28135 Heavy Duty Metal Bender
#20521 4” Metal Bender