Easy Track Deluxe RD04 User manual

LOOK INSIDE
PARTS INCLUDED
drawer front (1)
drawer wrap (1)
drawer bottom (1)
ball-bearing slides (2)
knob (1)
HARDWARE INCLUDED
#8 x 1" drawer adjusting screws (2)
#6 x 1/2" flat head screws (6)
euro screws (4)
white glue pouch (1)
AS EASY AS IT GETS.
RD04
RD08
RD12
Deluxe Drawer
11
22
3
3
4
4
5
5
Get the big picture.
Read these installation instructions. Check
to see you have all the parts on the
hardware list.
Gather the tools you’ll need.
SCREWDRIVER
MALLET

NOTE
Assemble drawer box. Fold the drawer wrap around
drawer bottom. Tap the doweled corners together with a rubber
mallet, so ends are tight and corners square. Wipe off excess
glue and allow to dry.
Make certain drawer box is square,
or it may not close properly.
1
2
Lay the drawer wrap flat on the floor. Apply a small amount of glue (provided) into the dowel holes, and then
apply glue into the three (3) v-grooves. Position the drawer bottom into the slot on the drawer wrap.
TEAR HERE
GLUE POUCH
TEAR HERE
GLUE POUCH
Apply glue in dowel holes
Drawer Wrap
Apply Gluein
v-grooves

A
B
A
B
DRAWER BOTTOM
BOTTOM OF DRAWER
4
3
5
Attach the knob to drawer front with supplied screw. Attach
drawer front to the drawer box using (2) #8 x 1" drawer
adjusting screws. Hand tighten the screws with a screwdriver to
bring the drawer front to drawer wrap.
Use the supplied paper templates included in the instructions
to mark hole locations by pushing the screw point through the
template in the places marked "screw hole".
Separate slide halves from each other by lifting the lever (1),
and pulling apart the slide (2).
#8 x 1" drawer adjusting screws
#6 x 1/2" flat head screws

NOTE
TIP
Press the closed side of the slide against the back
of the drawer front. Attach the smaller half of the
drawer slide to the drawer box using #6 x 1/2" screws at the
marked locations.
Slide fits tight to drawer front, leaving a small gap at the back of the
drawer. Note: 8" drawer shown below.
Position the front edge of the slide to the front edge
of the vertical. The 4th and 11th hole from the front
of the slide should be in line with the holes in the
vertical panel. Secure the slide using 2 euro screws
on each side. Skip one set of holes when the drawer is directly
above a fixed shelf.
See next step for drawer spacing guidelines.
6 7
Euro Screw
#6 x 1/2" flat head screws
1 21/32" or 42mm
Push slide tight to front
DRAWER SIDE

TIP
Line up the two drawer box slides with the slides on the two
verticals, and push into tower. Slides should lock.
8When installing drawers, use the screws provided to fix a shelf directly
above and below one drawer, or above and below a bank of drawers
for stability.
When installing drawers side by side, use two
vertical panels.
When using more than one drawer, leave 3 holes between slides for 4"
drawers, 5 holes between slides for 8" drawers, and 8 holes between
slides for 12" drawers.

BOTTOM OF DRAWER
BOTTOM OF DRAWER
13 7/8"
352 mm
352 mm
DELUXE DRAWER
RD04 RD08 RD12
SLIDE TEMPLATE A
SLIDE B
FRONT OF DRAWER
BACK OF DRAWER
BACK OF DRAWER
FRONT OF DRAWER
✂
CUT HERE
✂
CUT HERE
✂
CUT HERE
✂ CUT HERE
.75"
19 mm
.75"
19 mm
1 21⁄32"
42 mm
1 21⁄32"
42 mm
1 21⁄32"
42 mm
1 21⁄32"
42 mm
1 13⁄16"
46 mm
1 13⁄16"
46 mm
SCREW HOLE
SCREW HOLE
SCREW HOLE
SCREW HOLE

BOTTOM OF DRAWER
BOTTOM OF DRAWER \\\\
1"
1"
FRONT OF DRAWER
FRONT OF DRAWER
✂
CUT HERE
✂ ✂
✂
CUT HERE
✂ ✂
✂
CUT HERE
✂
CUT HERE
✂ ✂
2 5⁄16"
59 mm
2 5⁄16"
59 mm
1 21⁄32"
42 mm
1 21⁄32"
42 mm
1 21⁄32"
42 mm
1 21⁄32"
42 mm
1 7⁄8"
48 mm
SCREW HOLE
SCREW HOLE
SCREW HOLE
FROM BACK OF DRAWER
1 7⁄8"
48 mm SCREW HOLE
FROM BACK OF DRAWER
HUTCH DRAWER
RDH08
RDH12
SLIDE A
SLIDE B
Looking for home shop? Visit our website.