EasyBraid WickGun 1000 User manual
© 2022 DESCO INDUSTRIES INC
Employee Owned
11520 K-Tel Drive, Minnetonka, Minnesota 55343
November 2022 Page 1 of 2
1000 WickGun™ Desoldering Braid Dispenser
Loading the WickGun™
Operating Instructions
Replacing the Cutter
Important - With WickGun™pointing left insert cassette with label
facing up so wick will feed from the right (counter clockwise).
1. Grasp cassette and pull out foam plug, then pull out
approximately 2 1/4" (57 mm) of wick.
2. Insert wick into guide slot. Rotate drive knob in feed
direction while seating cassette. Ensure wick is not
pinched between cassette and WickGun™ and that
cassette alignment tabs are seated in the alignment
slots in the gun.
3. If wick fails to feed, disengage cassette, grasp wick
and pull from wick guide slot, do not allow cassette
to unwind. Eliminate any kinks and/or frayed wick.
Repeat steps 1 –2.
1. Hold with thumb on drive knob and index nger over
the trigger.
2. Rotate drive knob in feed direction exposing 3/4" to
1" (19 to 25 mm) of wick. Do not press on the trigger
while dispensing wick.
3. Perform desoldering operation.
4. Squeeze trigger to cut o lled wick.
Caution: to prevent jamming, do not retract wick
more than 1/2" (12 mm) past cutting blades and never
retract solder saturated wick past cutting blades.
1. To remove cutter:
A. Remove lever by pressing up and sliding
forward.
B. Slide nose clip up, then out to disengage.
C. Slide cutter out through front.
2. To install new Cutter:
A. Slide cutter inserting feed tube through slot in
back.
B. Slide lever into place. Nose clip tabs must be
seated in lever locator holes. Compress with
appropiate object pushed through small hole in
lever to facilitate this step.
3. To maintain good cutting action periodically remove
blades and clean with ux solvent.
AVOID contact between solvent and plastic parts.
FEED DIRECTION
DRIVE KNOBNOSE CLIP
LEVER
TRIGGER
STEP B.
LEVERLEVER LOCATOR HOLES
STEP A.
NOSE CLIPSTEP C.
CUTTER
CUTTING BLADE
SCREW
© 2022 DESCO INDUSTRIES INC
Employee Owned
11520 K-Tel Drive, Minnetonka, Minnesota 55343
November 2022 Page 2 of 2
1000 WickGun™ Desoldering Braid Dispenser
Replacement Cassettes
PART NO. DESCRIPTION
W4015-1 Cassette, Replacement, #1 Quick Braid Rosin Wick
W4015-1LF Cassette, Replacement, #1 Wick, Lead-Free
W4015-1NC Cassette, Replacement, #1 One Step No-Clean Wick
W4015-1NF Cassette, Replacement, #1 Wick, Sea Braid Unuxed
W4015-2 Cassette, Replacement, #2 Quick Braid Rosin Wick
W4015-2LF Cassette, Replacement, #2 Wick, Lead-Free
W4015-2NC Cassette, Replacement, #2 One Step No-Clean Wick
W4015-2NF Cassette, Replacement, #2 Wick, Sea Braid Unuxed
W4015-3 Cassette, Replacement, #3 Quick Braid Rosin Wick
W4015-3LF Cassette, Replacement, #3 Wick, Lead-Free
W4015-3NC Cassette, Replacement, #3 One Step No-Clean Wick
W4015-3NF Cassette, Replacement, #3 Wick, Sea Braid Unuxed
W4015-4 Cassette, Replacement, #4 Quick Braid Rosin Wick
W4015-4LF Cassette, Replacement, #4 Wick, Lead-Free
W4015-4NC Cassette, Replacement, #4 One Step No-Clean Wick
W4015-4NF Cassette, Replacement, #4 Wick, Sea Braid Unuxed
W4015-5 Cassette, Replacement, #5 Quick Braid Rosin Wick
W4015-5LF Cassette, Replacement, #5 Wick, Lead-Free
W4015-5NC Cassette, Replacement, #5 One Step No-Clean Wick
W4015-5NF Cassette, Replacement, #5 Wick, Sea Braid Unuxed
Table of contents
