Easylife 2890 User manual

1.
then dry.
2. Holding the tab, twist the cap anti clockwise
and pull to remove.
3. Pour up to 330ml of paint into the Edger Head
using the Easy Pour Jug (Fig. 7).
4. Replace the cap and twist to lock in place,
push the tab back down.
5. Clean any excess off the Edger head, if
required.
6. Filter paint through the Edger Head by rolling
it on an old newspaper for 2 minutes or until
fully covered with paint (Fig. 8).
7. The Edger Head is now ready for use.
8. When painting, ensure that the Edger head is
tilted at an angle from the adjacent wall. The
sponge portion should be seated fully on the
painted wall (Fig. 9).
Cleaning the Flocked Edger
1. Lift the Cap handle and twist anti-clockwise
to open
2. Dispose of the excess paint responsibly.
3. Remove the Cap and Preventor Plate from
the Edger Head and rinse with water until
clean. Dry out for immediate use by rolling on
newspaper or a cloth.
Air-dry for later use.
Please read manual thoroughly before use
1. Only use acrylic or latex paints (no enamel or oil-based paints).
2. Always stir paint thoroughly before use.
3. If paint is too thick, mix in a little water as per manufacturer’s
instructions to acheive desired consistency.
4.
5.
6. As with all DIY/Decorating activities, always make sure that you take
the appropriate safety precautions.
7. If Edger Head is loose, it has not been pushed on to the
Paint roller
INSTRUCTION MANUAL
Model No. 2890
Please read carefully before use and keep for future reference
Easy Pour
Jug
Resting
Tray
Corner
Pad
Flocked
Edger
Paint
Pole
Roller
Disposal
• Please respect the environment!
• Dispose of the packaging according to the local recycling regulations.
• Dispose of the appliance at the end of its life span according to environmental consideration
TECHNICALSPECIFICATION
Material: PP and velvet
Measurement:
Paint roller: 19.5x20.2x9.0cm (velvet section: 16.5cm)- It can load maximum 800ml paint
Flocked edger: 29x9.5dia cm - It can load maximum 330ml paint
Corner pad: 20x7.5x4.5cm
Resting tray: 22x11x1.6cm
Easy Pour Jug: 20.5x9.1x15cm
Support Line: 0333 030 0777
www.easylife.co.uk
IN2890 © 2021 Easylife Ltd.
Pole length: 67cm without roller / 90cm with roller

Preparing your Paint Roller for use
1.
2. Remove the Cap from Paint Roller
3. Pour up to 800ml of paint into the Paint Roller using
the Easy Pour Jug (Fig. 1)
4. Replace the Cap and make sure it is thoroughly
secure (it will click into place).
5.
running it over old newspaper for 2-3 minutes or
until paint is visible all over the roller (Fig. 2)
Your Paint Roller is now ready for use
Using the Paint Roller
1. Make sure you are happy with the weight of the
Paint Roller. If not, carefully remove the Cap and
pour paint back into the can until the roller is a more
comfortable weight.
2. For ceilings and high walls you can use a threaded
pole or broom handle.
3. When working at height, always ensure you have a
4. When using a pole, always ensure you are directly
under the weight of the Roller (Fig. 3)
5. Do not press too hard, let the Paint Roller do the
work for you.
During Intervals
If taking a short break, place on resting tray. If you are going to stop painting
for more than 2 hours, wrap the roller tightly with plastic wrap and store in a
cool dark place to prevent drying out.
Washing the Paint runner & changing the head
Remove the Cap from your Paint Roller
and rinse with warm running water until
clean. Dry out for immediate use by rolling
on newspaper or a cloth.
Air-dry for later use.
To change the Paint Roller head, remove
the Cap and Safety Cap. Prise the handle
apart to release the head. Replace with
a new head, replace the Safety Cap and
Cap (Fig. 4).
Attach pole to the roller
1.
insterted into handle
2. Threaded pole to be used with Pole Adaptor (Fig. 5)
Support Line: 0333 030 0777
www.easylife.co.uk