Easypix PO2 User manual

1
USER MANUAL
Product introduction
A Pulse Oximeter is a common device used to check oxygen
saturation (SpO²) and pulse rate.
It is a compact, reliable and durable physiological
monitoring device featuring an OLED display and powered
by 2 x AAA batteries (not included).
Intended use
The Pulse Oximeter is reusable device and is intended for
spot checking the pulse oxygen saturation and pulse rate of
adults.
It should not be used for continuous monitoring – this
should only be done under the guidance of your doctor.
Restrictions
Use of the device is for adults only.
Please do not use the device for children, infants and
neonatal. The product is not suitable for children under
3 years because of choking hazard.
Safety instructions
The person using the Pulse Oximeter must have read the
instructions for use carefully.
This product should only be used to give an indicative or
reference reading. It should not be used to determine a
diagnosis without consultation with your doctor. Longer
term or ongoing use should only be under the guidance of
your doctor.
If you experience any discomfort in use, please stop
immediately and seek medical help.
When using the Pulse Oximeter the user should pay
attention to, and guarantee safety of the patient being
measured.
The Pulse Oximeter does not feature an alarm function. It
should not be used for continuous monitoring for an
extended period.
Damaged skin tissue can not be measured.
Do not use the device if it has been damaged in any way.
Do not use the device in any way other than that described
in this manual.
Do not to use the Pulse Oximeter during MRI (magnetic
resonance imaging) scanning or CT (Computed
Tomography) environment as the induced current could
potentially cause burns.
The device should not be modified, repaired or serviced in
any way by the end user.
Do not use the Pulse Oximeter in the presence of
flammable anesthetics, explosive substances, vapors or
liquids.
Ensure the device is always clean and free from dirt before
use.
Before cleaning the device, ensure it is turned off.
Do not use high pressure or high temperature to disinfect or
clean the device. Never use cleaning agents/disinfectants
other than those recommended.
The device is a factory sealed unit. Keep its surface dry and
clean, and prevent contact with liquids.
The Pulse Oximeter is precision device. Avoid pressure,
knocks, strong vibration or other mechanical damage.
Please store safely when not in use.
For disposal of Pulse Oximeter and accessories, follow local
regulations regarding disposal of such a device and
accessories. Do not dispose of randomly.
Use AAA alkaline batteries. Do not use carbon or poor
quality batteries. Remove the batteries if the product will
not be used for an extended period of time.
Avoid exposure to static electricity before using the Pulse
Oximeter.
When in use, keep the device away from radio receivers.
To avoid enhanced electromagnetic radiation or reduce
anti-electromagnetic interference performance, only use
the device as configured.
Portable and mobile radio frequency communication
equipment can affect the normal use of the pulse oximeter.
Storage environment
The Pulse Oximeter should not be close to or stored with
other equipment.
Always store the device and small parts such as batteries
out of the reach of children.
Always ensure suitable supervision of patients or others
where the device is used on a lanyard.
Box contents
Pulse Oximeter, Lanyard, User manual EN/DE
Technical data
•OLED display
•SpO²: Measurement range: 70-100%
Accuracy: ±2% (70%-99%)
•Pulse rate:
Measurement range: 30-240bpm
Accuracy: ±2bpm
•Working voltage: DC3V
•Battery type: 2x 1.5V AAA alkaline batteries
are required (not included)
•Power consumption: < 30mA
•Automatic shutdown after 10 seconds
•Bluetooth 4.0
•Use environment: 5°-40°C
Storage environment: -10°-40°C
Ambient humidity: 15%-80%
Atmospheric pressure: 70kPa-106kPa
•Size: 58 x 32 x 34 mm
•Weight: 50g (with two AAA batteries)
Description of the product
POWER / FUNCTION BUTTON
Function description
The Pulse Oximeter is used to measure arterial oxygen
saturation (SpO²) and the pulse rate. Oxygen saturation
indicates the percentage of haemoglobin in the arterial
blood that is loaded with oxygen.
The Pulse Oximeter uses two light beams of different
wavelengths for measurement. These light beams strike the
inserted finger inside the housing during measurement and
the arterial oxygen saturation is then calculated and
displayed on the Pulse Oximeter.
1. Infrared Light Emitting 2. Infrared Light receiver
You can also find these instructions
online under the following link:
DE: Sie finden diese Anleitung auch online
unter dem folgend angegebenen Link:
FR : Un manuel dans votre langue
est disponible sur Internet:
IT: Il manuale nella sua lingua
può essere trovato su Internet:
ES: Puede encontrar un manual en su idioma en Internet:
PT: Um manual em seu idioma
pode ser encontrado na Internet:
PL: Instrukcję w swoim języku możesz znaleźć na stronie:
SWE: En handbok på ditt språk finns på Internet:
NL: Een handleiding in uw taal vindt u op internet:
www.bit.ly/pulse-po2

1
USER MANUAL
Product introduction
A Pulse Oximeter is a common device used to check oxygen
saturation (SpO²) and pulse rate.
It is a compact, reliable and durable physiological
monitoring device featuring an OLED display and powered
by 2 x AAA batteries (not included).
Intended use
The Pulse Oximeter is reusable device and is intended for
spot checking the pulse oxygen saturation and pulse rate of
adults.
It should not be used for continuous monitoring – this
should only be done under the guidance of your doctor.
Restrictions
Use of the device is for adults only.
Please do not use the device for children, infants and
neonatal. The product is not suitable for children under
3 years because of choking hazard.
Safety instructions
The person using the Pulse Oximeter must have read the
instructions for use carefully.
This product should only be used to give an indicative or
reference reading. It should not be used to determine a
diagnosis without consultation with your doctor. Longer
term or ongoing use should only be under the guidance of
your doctor.
If you experience any discomfort in use, please stop
immediately and seek medical help.
When using the Pulse Oximeter the user should pay
attention to, and guarantee safety of the patient being
measured.
The Pulse Oximeter does not feature an alarm function. It
should not be used for continuous monitoring for an
extended period.
Damaged skin tissue can not be measured.
Do not use the device if it has been damaged in any way.
Do not use the device in any way other than that described
in this manual.
Do not to use the Pulse Oximeter during MRI (magnetic
resonance imaging) scanning or CT (Computed
Tomography) environment as the induced current could
potentially cause burns.
The device should not be modified, repaired or serviced in
any way by the end user.
Do not use the Pulse Oximeter in the presence of
flammable anesthetics, explosive substances, vapors or
liquids.
Ensure the device is always clean and free from dirt before
use.
Before cleaning the device, ensure it is turned off.
Do not use high pressure or high temperature to disinfect or
clean the device. Never use cleaning agents/disinfectants
other than those recommended.
The device is a factory sealed unit. Keep its surface dry and
clean, and prevent contact with liquids.
The Pulse Oximeter is precision device. Avoid pressure,
knocks, strong vibration or other mechanical damage.
Please store safely when not in use.
For disposal of Pulse Oximeter and accessories, follow local
regulations regarding disposal of such a device and
accessories. Do not dispose of randomly.
Use AAA alkaline batteries. Do not use carbon or poor
quality batteries. Remove the batteries if the product will
not be used for an extended period of time.
Avoid exposure to static electricity before using the Pulse
Oximeter.
When in use, keep the device away from radio receivers.
To avoid enhanced electromagnetic radiation or reduce
anti-electromagnetic interference performance, only use
the device as configured.
Portable and mobile radio frequency communication
equipment can affect the normal use of the pulse oximeter.
Storage environment
The Pulse Oximeter should not be close to or stored with
other equipment.
Always store the device and small parts such as batteries
out of the reach of children.
Always ensure suitable supervision of patients or others
where the device is used on a lanyard.
Box contents
Pulse Oximeter, Lanyard, User manual EN/DE
Technical data
•OLED display
•SpO²: Measurement range: 70-100%
Accuracy: ±2% (70%-99%)
•Pulse rate:
Measurement range: 30-240bpm
Accuracy: ±2bpm
•Working voltage: DC3V
•Battery type: 2x 1.5V AAA alkaline batteries
are required (not included)
•Power consumption: < 30mA
•Automatic shutdown after 10 seconds
•Bluetooth 4.0
•Use environment: 5°-40°C
Storage environment: -10°-40°C
Ambient humidity: 15%-80%
Atmospheric pressure: 70kPa-106kPa
•Size: 58 x 32 x 34 mm
•Weight: 50g (with two AAA batteries)
Description of the product
POWER / FUNCTION BUTTON
Function description
The Pulse Oximeter is used to measure arterial oxygen
saturation (SpO²) and the pulse rate. Oxygen saturation
indicates the percentage of haemoglobin in the arterial
blood that is loaded with oxygen.
The Pulse Oximeter uses two light beams of different
wavelengths for measurement. These light beams strike the
inserted finger inside the housing during measurement and
the arterial oxygen saturation is then calculated and
displayed on the Pulse Oximeter.
1. Infrared Light Emitting 2. Infrared Light receiver
You can also find these instructions
online under the following link:
DE: Sie finden diese Anleitung auch online
unter dem folgend angegebenen Link:
FR : Un manuel dans votre langue
est disponible sur Internet:
IT: Il manuale nella sua lingua
può essere trovato su Internet:
ES: Puede encontrar un manual en su idioma en Internet:
PT: Um manual em seu idioma
pode ser encontrado na Internet:
PL: Instrukcję w swoim języku możesz znaleźć na stronie:
SWE: En handbok på ditt språk finns på Internet:
NL: Een handleiding in uw taal vindt u op internet:
www.bit.ly/pulse-po2

1
USER MANUAL
Product introduction
A Pulse Oximeter is a common device used to check oxygen
saturation (SpO²) and pulse rate.
It is a compact, reliable and durable physiological
monitoring device featuring an OLED display and powered
by 2 x AAA batteries (not included).
Intended use
The Pulse Oximeter is reusable device and is intended for
spot checking the pulse oxygen saturation and pulse rate of
adults.
It should not be used for continuous monitoring – this
should only be done under the guidance of your doctor.
Restrictions
Use of the device is for adults only.
Please do not use the device for children, infants and
neonatal. The product is not suitable for children under
3 years because of choking hazard.
Safety instructions
The person using the Pulse Oximeter must have read the
instructions for use carefully.
This product should only be used to give an indicative or
reference reading. It should not be used to determine a
diagnosis without consultation with your doctor. Longer
term or ongoing use should only be under the guidance of
your doctor.
If you experience any discomfort in use, please stop
immediately and seek medical help.
When using the Pulse Oximeter the user should pay
attention to, and guarantee safety of the patient being
measured.
The Pulse Oximeter does not feature an alarm function. It
should not be used for continuous monitoring for an
extended period.
Damaged skin tissue can not be measured.
Do not use the device if it has been damaged in any way.
Do not use the device in any way other than that described
in this manual.
Do not to use the Pulse Oximeter during MRI (magnetic
resonance imaging) scanning or CT (Computed
Tomography) environment as the induced current could
potentially cause burns.
The device should not be modified, repaired or serviced in
any way by the end user.
Do not use the Pulse Oximeter in the presence of
flammable anesthetics, explosive substances, vapors or
liquids.
Ensure the device is always clean and free from dirt before
use.
Before cleaning the device, ensure it is turned off.
Do not use high pressure or high temperature to disinfect or
clean the device. Never use cleaning agents/disinfectants
other than those recommended.
The device is a factory sealed unit. Keep its surface dry and
clean, and prevent contact with liquids.
The Pulse Oximeter is precision device. Avoid pressure,
knocks, strong vibration or other mechanical damage.
Please store safely when not in use.
For disposal of Pulse Oximeter and accessories, follow local
regulations regarding disposal of such a device and
accessories. Do not dispose of randomly.
Use AAA alkaline batteries. Do not use carbon or poor
quality batteries. Remove the batteries if the product will
not be used for an extended period of time.
Avoid exposure to static electricity before using the Pulse
Oximeter.
When in use, keep the device away from radio receivers.
To avoid enhanced electromagnetic radiation or reduce
anti-electromagnetic interference performance, only use
the device as configured.
Portable and mobile radio frequency communication
equipment can affect the normal use of the pulse oximeter.
Storage environment
The Pulse Oximeter should not be close to or stored with
other equipment.
Always store the device and small parts such as batteries
out of the reach of children.
Always ensure suitable supervision of patients or others
where the device is used on a lanyard.
Box contents
Pulse Oximeter, Lanyard, User manual EN/DE
Technical data
•OLED display
•SpO²: Measurement range: 70-100%
Accuracy: ±2% (70%-99%)
•Pulse rate:
Measurement range: 30-240bpm
Accuracy: ±2bpm
•Working voltage: DC3V
•Battery type: 2x 1.5V AAA alkaline batteries
are required (not included)
•Power consumption: < 30mA
•Automatic shutdown after 10 seconds
•Bluetooth 4.0
•Use environment: 5°-40°C
Storage environment: -10°-40°C
Ambient humidity: 15%-80%
Atmospheric pressure: 70kPa-106kPa
•Size: 58 x 32 x 34 mm
•Weight: 50g (with two AAA batteries)
Description of the product
POWER / FUNCTION BUTTON
Function description
The Pulse Oximeter is used to measure arterial oxygen
saturation (SpO²) and the pulse rate. Oxygen saturation
indicates the percentage of haemoglobin in the arterial
blood that is loaded with oxygen.
The Pulse Oximeter uses two light beams of different
wavelengths for measurement. These light beams strike the
inserted finger inside the housing during measurement and
the arterial oxygen saturation is then calculated and
displayed on the Pulse Oximeter.
1. Infrared Light Emitting 2. Infrared Light receiver
You can also find these instructions
online under the following link:
DE: Sie finden diese Anleitung auch online
unter dem folgend angegebenen Link:
FR : Un manuel dans votre langue
est disponible sur Internet:
IT: Il manuale nella sua lingua
può essere trovato su Internet:
ES: Puede encontrar un manual en su idioma en Internet:
PT: Um manual em seu idioma
pode ser encontrado na Internet:
PL: Instrukcję w swoim języku możesz znaleźć na stronie:
SWE: En handbok på ditt språk finns på Internet:
NL: Een handleiding in uw taal vindt u op internet:
www.bit.ly/pulse-po2

1
USER MANUAL
Product introduction
A Pulse Oximeter is a common device used to check oxygen
saturation (SpO²) and pulse rate.
It is a compact, reliable and durable physiological
monitoring device featuring an OLED display and powered
by 2 x AAA batteries (not included).
Intended use
The Pulse Oximeter is reusable device and is intended for
spot checking the pulse oxygen saturation and pulse rate of
adults.
It should not be used for continuous monitoring – this
should only be done under the guidance of your doctor.
Restrictions
Use of the device is for adults only.
Please do not use the device for children, infants and
neonatal. The product is not suitable for children under
3 years because of choking hazard.
Safety instructions
The person using the Pulse Oximeter must have read the
instructions for use carefully.
This product should only be used to give an indicative or
reference reading. It should not be used to determine a
diagnosis without consultation with your doctor. Longer
term or ongoing use should only be under the guidance of
your doctor.
If you experience any discomfort in use, please stop
immediately and seek medical help.
When using the Pulse Oximeter the user should pay
attention to, and guarantee safety of the patient being
measured.
The Pulse Oximeter does not feature an alarm function. It
should not be used for continuous monitoring for an
extended period.
Damaged skin tissue can not be measured.
Do not use the device if it has been damaged in any way.
Do not use the device in any way other than that described
in this manual.
Do not to use the Pulse Oximeter during MRI (magnetic
resonance imaging) scanning or CT (Computed
Tomography) environment as the induced current could
potentially cause burns.
The device should not be modified, repaired or serviced in
any way by the end user.
Do not use the Pulse Oximeter in the presence of
flammable anesthetics, explosive substances, vapors or
liquids.
Ensure the device is always clean and free from dirt before
use.
Before cleaning the device, ensure it is turned off.
Do not use high pressure or high temperature to disinfect or
clean the device. Never use cleaning agents/disinfectants
other than those recommended.
The device is a factory sealed unit. Keep its surface dry and
clean, and prevent contact with liquids.
The Pulse Oximeter is precision device. Avoid pressure,
knocks, strong vibration or other mechanical damage.
Please store safely when not in use.
For disposal of Pulse Oximeter and accessories, follow local
regulations regarding disposal of such a device and
accessories. Do not dispose of randomly.
Use AAA alkaline batteries. Do not use carbon or poor
quality batteries. Remove the batteries if the product will
not be used for an extended period of time.
Avoid exposure to static electricity before using the Pulse
Oximeter.
When in use, keep the device away from radio receivers.
To avoid enhanced electromagnetic radiation or reduce
anti-electromagnetic interference performance, only use
the device as configured.
Portable and mobile radio frequency communication
equipment can affect the normal use of the pulse oximeter.
Storage environment
The Pulse Oximeter should not be close to or stored with
other equipment.
Always store the device and small parts such as batteries
out of the reach of children.
Always ensure suitable supervision of patients or others
where the device is used on a lanyard.
Box contents
Pulse Oximeter, Lanyard, User manual EN/DE
Technical data
•OLED display
•SpO²: Measurement range: 70-100%
Accuracy: ±2% (70%-99%)
•Pulse rate:
Measurement range: 30-240bpm
Accuracy: ±2bpm
•Working voltage: DC3V
•Battery type: 2x 1.5V AAA alkaline batteries
are required (not included)
•Power consumption: < 30mA
•Automatic shutdown after 10 seconds
•Bluetooth 4.0
•Use environment: 5°-40°C
Storage environment: -10°-40°C
Ambient humidity: 15%-80%
Atmospheric pressure: 70kPa-106kPa
•Size: 58 x 32 x 34 mm
•Weight: 50g (with two AAA batteries)
Description of the product
POWER / FUNCTION BUTTON
Function description
The Pulse Oximeter is used to measure arterial oxygen
saturation (SpO²) and the pulse rate. Oxygen saturation
indicates the percentage of haemoglobin in the arterial
blood that is loaded with oxygen.
The Pulse Oximeter uses two light beams of different
wavelengths for measurement. These light beams strike the
inserted finger inside the housing during measurement and
the arterial oxygen saturation is then calculated and
displayed on the Pulse Oximeter.
1. Infrared Light Emitting 2. Infrared Light receiver
You can also find these instructions
online under the following link:
DE: Sie finden diese Anleitung auch online
unter dem folgend angegebenen Link:
FR : Un manuel dans votre langue
est disponible sur Internet:
IT: Il manuale nella sua lingua
può essere trovato su Internet:
ES: Puede encontrar un manual en su idioma en Internet:
PT: Um manual em seu idioma
pode ser encontrado na Internet:
PL: Instrukcję w swoim języku możesz znaleźć na stronie:
SWE: En handbok på ditt språk finns på Internet:
NL: Een handleiding in uw taal vindt u op internet:
www.bit.ly/pulse-po2

2
Measuring steps
1. Remove the battery compartment cover and insert the
batteries as shown in Figure 1. Securely re-fit the battery
compartment cover.
2. Press the power / function button on the front panel to
switch on the device.
3. Squeeze one end of the device to open it and place an
index finger inside. Allow the device to gently close on the
finger as shown in Figure 2. (Index, middle or ring fingers
can be used for a reading)
Keep the finger and device still with as little movement as
possible and allow the device to take a measurement.
Ensure the finger is inserted far enough into the sensor so
that the fingernail is just opposite to the light emitted
from the sensor.
Figure 1 Figure 2
Do not perform SpO² monitoring and NIBP (Non-invasive
blood pressure) measurements on the same arm
simultaneously. Obstruction of blood flow during NIBP
measurements may adversely affect the reading of the
SpO² value.
Do not use the Pulse Oximeter to measure patients whose
pulse rate is lower than 30bpm, as this may cause incorrect
results.
Ensure there is no contamination and/or scars on the tested
finger as the result indicated may be incorrect due to the
signal received by the sensor being affected.
When used on various patients, the product is prone to
cross contamination, which should be prevented and
controlled by the user. Disinfection is recommended before
using the product on other patients.
The highest temperature threshold of the sensor contacts
with a patient’s skin is 41°C.
Repeat use may require the use of different fingers to
obtain a measurement.
Factors affecting measurement accuracy
Incorrect placement of the finger may affect the accuracy of
the measurement.
The measurements also depend on absorption of a special
wavelength ray by oxidized hemoglobin and
deoxyhemoglobin. Concentration of nonfunctional
hemoglobin may affect the accuracy of the measurement.
Always consult a doctor if in doubt.
Shock, anemia, hypothermia and the application of
vasoconstriction drug may decrease arterial blood flow to
an unmeasurable level.
Pigment, or deep color (for example: nail polish, artificial
nails, dye or pigmented cream) may cause inaccurate
measurements.
Rotate the display
To rotate the display for convenient reading, when the
result has been displayed on the screen, short press the
“POWER/FUNCTION” button once.
Auto switch off
The product will switch off automatically after 10 seconds
of no signal being detected.
Transfer of measurement results
to your smartphone (via Bluetooth)
Thanks to the integrated Bluetooth function, you can
transfer the measurement results to your smartphone.
1. Switch on the Bluetooth function on your smartphone.
2. Download and install the app "SMART WEAR".
ANDROID IOS
3. When installing, follow the steps described in the app
and connect to the SP001 device.
4. The next measurement is automatically transferred
from the Pulse Oximeter to your smartphone.
5. This allows you to save the measurements as an image,
send them or share them with others.
Lanyard placement
1. Thread the thinner end of the lanyard through the hole.
2. Thread the thicker end of the lace through the threaded
end before pulling it tightly.
Cleaning and disinfection
Clean the product with cotton or damp soft cloth.
After cleaning, wipe dry and allow to full air dry.
Disinfection
The recommended disinfectants include: ethanol 70%,
isopropanol 70%, glutaraldehyde (2%) solution
disinfectants.
Clean the product as instructed above.
Disinfect the product with cotton or soft cloth moistened
with one of the recommended disinfectants.
After disinfection, be sure to wipe off the disinfectant left
on the product with a soft cloth moistened with water.
Allow the product to air dry.
Never immerse the device in liquid.
We recommend cleaning and disinfecting the product when
necessary or when used with different patients.
Never use cleaning agents/disinfectants other than those
recommended.
Never permit high-pressure and high-temperature
disinfection of the device.
Always switch off the device and remove the batteries
before cleaning or disinfecting.
Disposal
Dispose of packaging
Before disposal, please ensure separation of
the different packaging included with this
product. Cardboard must be disposed of as
paper while foil or plastics must be recycled.
Disposal of Waste Electrical and Electronic
Equipment and/or Battery by users in private
households in the European Union.
This symbol on the product or on the packaging indicates
that this cannot be disposed of as a household waste. You
must dispose of your waste equipment and/or battery by
handling it over to the applicable take-back scheme for the
recycling of electrical and electronic equipment and/or
battery. For more information about recycling of this
equipment and/or battery, please contact your city office,
the shop where you purchased the equipment or your
household waste disposal service. The recycling of materials
will help to conserve natural resources and ensure that it is
recycled in a manner that protects human health and
environment.
Declaration of conformity
We hereby declare that the CE marking has been affixed to
this product in accordance with the essential requirements
and relevant provisions of the European directives.
The declaration of conformity can be downloaded here:
www.easypix.info/download/pdf/
doc_pulseoximeter_po2.pdf
This explanation is given for the manufacturer / importer
easypix GmbH
Em Parkveedel 11
50733 Köln, Germany

2
Measuring steps
1. Remove the battery compartment cover and insert the
batteries as shown in Figure 1. Securely re-fit the battery
compartment cover.
2. Press the power / function button on the front panel to
switch on the device.
3. Squeeze one end of the device to open it and place an
index finger inside. Allow the device to gently close on the
finger as shown in Figure 2. (Index, middle or ring fingers
can be used for a reading)
Keep the finger and device still with as little movement as
possible and allow the device to take a measurement.
Ensure the finger is inserted far enough into the sensor so
that the fingernail is just opposite to the light emitted
from the sensor.
Figure 1 Figure 2
Do not perform SpO² monitoring and NIBP (Non-invasive
blood pressure) measurements on the same arm
simultaneously. Obstruction of blood flow during NIBP
measurements may adversely affect the reading of the
SpO² value.
Do not use the Pulse Oximeter to measure patients whose
pulse rate is lower than 30bpm, as this may cause incorrect
results.
Ensure there is no contamination and/or scars on the tested
finger as the result indicated may be incorrect due to the
signal received by the sensor being affected.
When used on various patients, the product is prone to
cross contamination, which should be prevented and
controlled by the user. Disinfection is recommended before
using the product on other patients.
The highest temperature threshold of the sensor contacts
with a patient’s skin is 41°C.
Repeat use may require the use of different fingers to
obtain a measurement.
Factors affecting measurement accuracy
Incorrect placement of the finger may affect the accuracy of
the measurement.
The measurements also depend on absorption of a special
wavelength ray by oxidized hemoglobin and
deoxyhemoglobin. Concentration of nonfunctional
hemoglobin may affect the accuracy of the measurement.
Always consult a doctor if in doubt.
Shock, anemia, hypothermia and the application of
vasoconstriction drug may decrease arterial blood flow to
an unmeasurable level.
Pigment, or deep color (for example: nail polish, artificial
nails, dye or pigmented cream) may cause inaccurate
measurements.
Rotate the display
To rotate the display for convenient reading, when the
result has been displayed on the screen, short press the
“POWER/FUNCTION” button once.
Auto switch off
The product will switch off automatically after 10 seconds
of no signal being detected.
Transfer of measurement results
to your smartphone (via Bluetooth)
Thanks to the integrated Bluetooth function, you can
transfer the measurement results to your smartphone.
1. Switch on the Bluetooth function on your smartphone.
2. Download and install the app "SMART WEAR".
ANDROID IOS
3. When installing, follow the steps described in the app
and connect to the SP001 device.
4. The next measurement is automatically transferred
from the Pulse Oximeter to your smartphone.
5. This allows you to save the measurements as an image,
send them or share them with others.
Lanyard placement
1. Thread the thinner end of the lanyard through the hole.
2. Thread the thicker end of the lace through the threaded
end before pulling it tightly.
Cleaning and disinfection
Clean the product with cotton or damp soft cloth.
After cleaning, wipe dry and allow to full air dry.
Disinfection
The recommended disinfectants include: ethanol 70%,
isopropanol 70%, glutaraldehyde (2%) solution
disinfectants.
Clean the product as instructed above.
Disinfect the product with cotton or soft cloth moistened
with one of the recommended disinfectants.
After disinfection, be sure to wipe off the disinfectant left
on the product with a soft cloth moistened with water.
Allow the product to air dry.
Never immerse the device in liquid.
We recommend cleaning and disinfecting the product when
necessary or when used with different patients.
Never use cleaning agents/disinfectants other than those
recommended.
Never permit high-pressure and high-temperature
disinfection of the device.
Always switch off the device and remove the batteries
before cleaning or disinfecting.
Disposal
Dispose of packaging
Before disposal, please ensure separation of
the different packaging included with this
product. Cardboard must be disposed of as
paper while foil or plastics must be recycled.
Disposal of Waste Electrical and Electronic
Equipment and/or Battery by users in private
households in the European Union.
This symbol on the product or on the packaging indicates
that this cannot be disposed of as a household waste. You
must dispose of your waste equipment and/or battery by
handling it over to the applicable take-back scheme for the
recycling of electrical and electronic equipment and/or
battery. For more information about recycling of this
equipment and/or battery, please contact your city office,
the shop where you purchased the equipment or your
household waste disposal service. The recycling of materials
will help to conserve natural resources and ensure that it is
recycled in a manner that protects human health and
environment.
Declaration of conformity
We hereby declare that the CE marking has been affixed to
this product in accordance with the essential requirements
and relevant provisions of the European directives.
The declaration of conformity can be downloaded here:
www.easypix.info/download/pdf/
doc_pulseoximeter_po2.pdf
This explanation is given for the manufacturer / importer
easypix GmbH
Em Parkveedel 11
50733 Köln, Germany

2
Measuring steps
1. Remove the battery compartment cover and insert the
batteries as shown in Figure 1. Securely re-fit the battery
compartment cover.
2. Press the power / function button on the front panel to
switch on the device.
3. Squeeze one end of the device to open it and place an
index finger inside. Allow the device to gently close on the
finger as shown in Figure 2. (Index, middle or ring fingers
can be used for a reading)
Keep the finger and device still with as little movement as
possible and allow the device to take a measurement.
Ensure the finger is inserted far enough into the sensor so
that the fingernail is just opposite to the light emitted
from the sensor.
Figure 1 Figure 2
Do not perform SpO² monitoring and NIBP (Non-invasive
blood pressure) measurements on the same arm
simultaneously. Obstruction of blood flow during NIBP
measurements may adversely affect the reading of the
SpO² value.
Do not use the Pulse Oximeter to measure patients whose
pulse rate is lower than 30bpm, as this may cause incorrect
results.
Ensure there is no contamination and/or scars on the tested
finger as the result indicated may be incorrect due to the
signal received by the sensor being affected.
When used on various patients, the product is prone to
cross contamination, which should be prevented and
controlled by the user. Disinfection is recommended before
using the product on other patients.
The highest temperature threshold of the sensor contacts
with a patient’s skin is 41°C.
Repeat use may require the use of different fingers to
obtain a measurement.
Factors affecting measurement accuracy
Incorrect placement of the finger may affect the accuracy of
the measurement.
The measurements also depend on absorption of a special
wavelength ray by oxidized hemoglobin and
deoxyhemoglobin. Concentration of nonfunctional
hemoglobin may affect the accuracy of the measurement.
Always consult a doctor if in doubt.
Shock, anemia, hypothermia and the application of
vasoconstriction drug may decrease arterial blood flow to
an unmeasurable level.
Pigment, or deep color (for example: nail polish, artificial
nails, dye or pigmented cream) may cause inaccurate
measurements.
Rotate the display
To rotate the display for convenient reading, when the
result has been displayed on the screen, short press the
“POWER/FUNCTION” button once.
Auto switch off
The product will switch off automatically after 10 seconds
of no signal being detected.
Transfer of measurement results
to your smartphone (via Bluetooth)
Thanks to the integrated Bluetooth function, you can
transfer the measurement results to your smartphone.
1. Switch on the Bluetooth function on your smartphone.
2. Download and install the app "SMART WEAR".
ANDROID IOS
3. When installing, follow the steps described in the app
and connect to the SP001 device.
4. The next measurement is automatically transferred
from the Pulse Oximeter to your smartphone.
5. This allows you to save the measurements as an image,
send them or share them with others.
Lanyard placement
1. Thread the thinner end of the lanyard through the hole.
2. Thread the thicker end of the lace through the threaded
end before pulling it tightly.
Cleaning and disinfection
Clean the product with cotton or damp soft cloth.
After cleaning, wipe dry and allow to full air dry.
Disinfection
The recommended disinfectants include: ethanol 70%,
isopropanol 70%, glutaraldehyde (2%) solution
disinfectants.
Clean the product as instructed above.
Disinfect the product with cotton or soft cloth moistened
with one of the recommended disinfectants.
After disinfection, be sure to wipe off the disinfectant left
on the product with a soft cloth moistened with water.
Allow the product to air dry.
Never immerse the device in liquid.
We recommend cleaning and disinfecting the product when
necessary or when used with different patients.
Never use cleaning agents/disinfectants other than those
recommended.
Never permit high-pressure and high-temperature
disinfection of the device.
Always switch off the device and remove the batteries
before cleaning or disinfecting.
Disposal
Dispose of packaging
Before disposal, please ensure separation of
the different packaging included with this
product. Cardboard must be disposed of as
paper while foil or plastics must be recycled.
Disposal of Waste Electrical and Electronic
Equipment and/or Battery by users in private
households in the European Union.
This symbol on the product or on the packaging indicates
that this cannot be disposed of as a household waste. You
must dispose of your waste equipment and/or battery by
handling it over to the applicable take-back scheme for the
recycling of electrical and electronic equipment and/or
battery. For more information about recycling of this
equipment and/or battery, please contact your city office,
the shop where you purchased the equipment or your
household waste disposal service. The recycling of materials
will help to conserve natural resources and ensure that it is
recycled in a manner that protects human health and
environment.
Declaration of conformity
We hereby declare that the CE marking has been affixed to
this product in accordance with the essential requirements
and relevant provisions of the European directives.
The declaration of conformity can be downloaded here:
www.easypix.info/download/pdf/
doc_pulseoximeter_po2.pdf
This explanation is given for the manufacturer / importer
easypix GmbH
Em Parkveedel 11
50733 Köln, Germany

2
Measuring steps
1. Remove the battery compartment cover and insert the
batteries as shown in Figure 1. Securely re-fit the battery
compartment cover.
2. Press the power / function button on the front panel to
switch on the device.
3. Squeeze one end of the device to open it and place an
index finger inside. Allow the device to gently close on the
finger as shown in Figure 2. (Index, middle or ring fingers
can be used for a reading)
Keep the finger and device still with as little movement as
possible and allow the device to take a measurement.
Ensure the finger is inserted far enough into the sensor so
that the fingernail is just opposite to the light emitted
from the sensor.
Figure 1 Figure 2
Do not perform SpO² monitoring and NIBP (Non-invasive
blood pressure) measurements on the same arm
simultaneously. Obstruction of blood flow during NIBP
measurements may adversely affect the reading of the
SpO² value.
Do not use the Pulse Oximeter to measure patients whose
pulse rate is lower than 30bpm, as this may cause incorrect
results.
Ensure there is no contamination and/or scars on the tested
finger as the result indicated may be incorrect due to the
signal received by the sensor being affected.
When used on various patients, the product is prone to
cross contamination, which should be prevented and
controlled by the user. Disinfection is recommended before
using the product on other patients.
The highest temperature threshold of the sensor contacts
with a patient’s skin is 41°C.
Repeat use may require the use of different fingers to
obtain a measurement.
Factors affecting measurement accuracy
Incorrect placement of the finger may affect the accuracy of
the measurement.
The measurements also depend on absorption of a special
wavelength ray by oxidized hemoglobin and
deoxyhemoglobin. Concentration of nonfunctional
hemoglobin may affect the accuracy of the measurement.
Always consult a doctor if in doubt.
Shock, anemia, hypothermia and the application of
vasoconstriction drug may decrease arterial blood flow to
an unmeasurable level.
Pigment, or deep color (for example: nail polish, artificial
nails, dye or pigmented cream) may cause inaccurate
measurements.
Rotate the display
To rotate the display for convenient reading, when the
result has been displayed on the screen, short press the
“POWER/FUNCTION” button once.
Auto switch off
The product will switch off automatically after 10 seconds
of no signal being detected.
Transfer of measurement results
to your smartphone (via Bluetooth)
Thanks to the integrated Bluetooth function, you can
transfer the measurement results to your smartphone.
1. Switch on the Bluetooth function on your smartphone.
2. Download and install the app "SMART WEAR".
ANDROID IOS
3. When installing, follow the steps described in the app
and connect to the SP001 device.
4. The next measurement is automatically transferred
from the Pulse Oximeter to your smartphone.
5. This allows you to save the measurements as an image,
send them or share them with others.
Lanyard placement
1. Thread the thinner end of the lanyard through the hole.
2. Thread the thicker end of the lace through the threaded
end before pulling it tightly.
Cleaning and disinfection
Clean the product with cotton or damp soft cloth.
After cleaning, wipe dry and allow to full air dry.
Disinfection
The recommended disinfectants include: ethanol 70%,
isopropanol 70%, glutaraldehyde (2%) solution
disinfectants.
Clean the product as instructed above.
Disinfect the product with cotton or soft cloth moistened
with one of the recommended disinfectants.
After disinfection, be sure to wipe off the disinfectant left
on the product with a soft cloth moistened with water.
Allow the product to air dry.
Never immerse the device in liquid.
We recommend cleaning and disinfecting the product when
necessary or when used with different patients.
Never use cleaning agents/disinfectants other than those
recommended.
Never permit high-pressure and high-temperature
disinfection of the device.
Always switch off the device and remove the batteries
before cleaning or disinfecting.
Disposal
Dispose of packaging
Before disposal, please ensure separation of
the different packaging included with this
product. Cardboard must be disposed of as
paper while foil or plastics must be recycled.
Disposal of Waste Electrical and Electronic
Equipment and/or Battery by users in private
households in the European Union.
This symbol on the product or on the packaging indicates
that this cannot be disposed of as a household waste. You
must dispose of your waste equipment and/or battery by
handling it over to the applicable take-back scheme for the
recycling of electrical and electronic equipment and/or
battery. For more information about recycling of this
equipment and/or battery, please contact your city office,
the shop where you purchased the equipment or your
household waste disposal service. The recycling of materials
will help to conserve natural resources and ensure that it is
recycled in a manner that protects human health and
environment.
Declaration of conformity
We hereby declare that the CE marking has been affixed to
this product in accordance with the essential requirements
and relevant provisions of the European directives.
The declaration of conformity can be downloaded here:
www.easypix.info/download/pdf/
doc_pulseoximeter_po2.pdf
This explanation is given for the manufacturer / importer
easypix GmbH
Em Parkveedel 11
50733 Köln, Germany