Eaton MEMSHIELD 3 Manual

Slacken
2 screws
marked
earth
IMPORTANT NOTES
1. This product should be installed, commissioned and maintained by or under the supervision of a competent electrician
in accordancewithcurrent electrical engineering Codes of Practice, Regulations for the Electrical equipment of
Buildings (BS7671), CDM2007 - Construction (Design and Management) Regulations 2007, HSG150 Health and
Safety in Construction, Statutory requirements and any Specific instruction issued by the Company.
2. Aftercompleting the installation and testing of this product it is essential that this leaflet is drawnto the attention of
the person responsible for its future operation and maintenance, and is at all times available for ready reference.
3. These notes assume throughout that the product is disconnected fromthe supply.It is essential that this is done
before any workis carried out.
MEMSHIELD 3 TYPE B TPN DISTRIBUTIONBOARD
Instruction leaflet LT1180 (01/21)
NEUTRAL LINKDISCONNECTION
Remove
screws
andlink
Tightento
3.8Nm
Incoming
neutral link
Tightento
5Nm
IMPORTANT
Replace ‘N’ link
andretighten
after test
Tightento
9Nm
FITTING ANMCB/RCBO
All unused waysmust
be fitted with a blanking
module,assembledand
fitted in gangsof 3.
Before fitting
to busbar
ensure MCB
terminalis
fullyopen
When fitting an RCBO, trim RCBO ‘N’ cable to length
and connect to ‘N’ busbar terminal.
Connect load live/neutral cable direct to RCBO.
IMPORTANT:
OrientateMCB
clip next to
busbar stack
Locate and
tighten terminal
screws
2.4Nm
Busbarassembly
can be removed for
ease of installation
CLEANEARTH
Clip fit
Earth/Neutral
terminal screws
Tighten to:
M4 -1.2Nm
M6 -2.5Nm
These DistributionBoardsare designedonlyfor use with
MCB’s and RCBO’s as listed in the current Memshield3
catalogue.
Failure to complywillresult in invalid warranty and
certification.
CAUTION
Do not fit SP & SN, or 4 pole MCB’s in TP type B board

FITTING EBMS1253
125A Switch Disconnector Kit
NOTE
125A Incoming device kits w ill fitboth 125A and
250A Boards
FITTING EBMS1251N
125A SPSN Switch DisconnectorKit
FITTING EBMS1253N
125A 4 pole SwitchDisconnectorKit
Ensure both neutral
shieldsare fitted after
installation Ensure both neutral
shieldsare fitted after
installation
WARNING
SHORTINGBARFITTED
Fit cover
with label
Neutral Link
to 5Nm
Ensure
washers supplied
are fitted
Tighten
terminalscrews
to 2.4Nm
Tighten
terminalscrews
to 2.4Nm
Neutral Link
screw tighten
to 3.8Nm
Shorting Bar Shorting Bar
screws tighten
Neutral Link
Neutral Link
screw tighten
to 3.8Nm
Fit main switch label
around coveraperture
Fit main switch label
around coveraperture
Fit main switch label
around coveraperture
Ensure both neutral
shieldsare fitted after
installation
Ensure both neutral
shieldsare fitted after
installation
Fit main switch label
around coveraperture
50mm2
Incomer
adaptor
FITTING EBMR30,100,300,300T
EBMRIK100 (RCCB notsupplied)
100A 4 Pole RCCB Kits
Neutral
Link
Neutral
Linkscrew
tighten to
3.8Nm
Secure 3 xconnectors
to busbarsusing screws
and washers provided
Tighten
terminalscrews
to 2.4Nm
Tighten
terminalscrews
to 2.4Nm

Note: Direct Cable Kit willfit
both 125A and 250A board
IMPORTANT:
Do notexceed busbarrating
Convert to
clean earth
FITTING EBMNE8
Additional earth, fix from
rearwith x2 earth nib
screws provided
FITTING EBMXPC1/2
Remove end plate andfix
extension boxin placewith x6
existing end plate screws
FITTING EBMBT2503
250A Direct Cable Kit
Tighten 3 off
terminalscrewsto 8Nm
Ensure washers
supplied are fitted
Ensure both neutral
shieldsare fitted after installation
Ensure both neutral
shieldsare fitted after
installation
Remove thin area(shaded)
inside shieldto allow
linkto be fitted
Single
phasing
link
FITTING EBMS25
250A Single PhasingConversion Kit
Ensure both
neutral shields
are fitted after
installation
WARNING
SHORTINGBARFITTED
Fit coverwith label
Tighten
terminal
screws to
15Nm
Slide incoming
assemblyinto
position and tighten
4off device mount
screws
Remove and discard
from cover
Tighten to
15Nm
Fit main switch label
beneath coveraperture
Tighten to
15Nm
IMPORTANT:Operation of the incomingmccb device
should only be carried out by an instructed orskilled person.
Tighten 3off M5 terminal
screws to 8Nm Ensure
washers supplied are fitted
M8 Neutral TerminalBolt
Tighten to 15Nm
Neutral Shield
FITTING EBMS2503,EBMMB160,200,250
250A Switch Disconnector/160-250A MCCB Kits
Important:
When fittingto EBM122/TP
maxrating 225A.
NOTE:Illustrationshows 250A
M6 Earth terminal
screws Tightento
2.5Nm

LH OUTGOING CIRCUITS RH OUTGOING CIRCUITS
FED FROM:
INCOMING CABLE SIZE:
INSTALLATION DATE:
CONTRACTOR:
DIMENSIONS (mm)
326
440
10
270
130
100
83
A
B
180
M6 Keyhole
fixing
Cable Box
FITTINGEMBL2
FITTING
DOOR LOCK EMDL &EMPL
Remove Plastic Knob
Insert Lock
into hole
tighten
back nut
For extrasecurity fit
padlock List No. PD2
Warning-
IntellectualPropertyRights
Eaton wishes to makeit clear thatit ownsintellectual property rights in the
product which it manufactures(whether or notlistedin thisleaflet) and that it
will take legal action againstany party found to be manufacturing,using, or
selling any article which infringes the company’s intellectual property. All
marks in thisdocument identifiedwith an R symbolor a TMsymbol adjacent
to the mark are trademarksofEaton.
©2019Eaton Electric Limited,
All rights reserved.
The use to which this product is put and its place of installation is outside our
control.Particularcareshouldtherefore betakentofollowthe instructionsgiven here
andtoensuretheircontinued availability inconjunction withthe use of theproduct.
No responsibility canbe acceptedby us if these instructions are disregarded. Fur-
thercopiesof theseinstructionsand informationconcerningtheinstallationandproper
use of thisproduct can be obtained by contactingthe:
TechnicalServicesDepartment
Eaton Electric Limited, Middleton, Manchester, M241GQ
Tel:[phone],
email: [e-mail]
www.eaton.com/recycling
CAT.No.
A B
EBM41
/TP
429
245
EBM61
/TP
482
298
EBM81
/TP
564
380
EBM121
/
TP
831
540
EBM122
/
TP
861
677
EBM161
/
TP
724
540
EBM182
/
TP
1021
837
EBM242
/
TP
1180
996
Earth bolt
Tighten to
15Nm