Eaton i-P65 Manual

Standard Fitting Double Sided Legend Fitting
Safe Operation
1. Check the rating label for voltage and frequency before connecting this luminaire to the electrical
supply.
2. Ensure that the mains supply is switched off when working on this luminaire, whether installing or
carrying out any other servicing.
3. To prevent damage to driver, do not mix with conventional magnetic ballasts on the same electrical
circuit.
4. Where use in more onerous situations is required, e.g. In part-completed buildings before “drying-out” is
completed, or areas where ambient temperatures are outside the normal temperature range, then
consult our Sales Office.
5. Ensure the fixing is adequate for the luminaire weight.
6. The change mode of operation from mains to emergency is automatically changed to emergency mode by the
integral PCB control gear
Servicing and Disposal
1. At commissioning and handing over of installation ensure that a copy of these instructions is presented
to the authority responsible for the operation and maintenance of the luminaries.
2. Servicing, e.g. cleaning, must only be carried out after the electricity supply has been switched off. It
must not be assumed that luminaries with lamps not lit are switched off-always check before servicing.
3. Cleaning should be carried out at regular intervals to ensure that dirt does not accumulate to an extent
that will impair the thermal safety or optical performance of the luminaire. Regular cleaning will also
ensure that the optical performance of the luminaries is maintained.
4. Avoid touching the LED. To clean - Blow surface with either dry air or nitrogen gas.
5. At the end of life the luminaire is classed as WEEE under directive 2002/96/EC and should be disposed
of in accordance with local legislation.
Battery Life
Performance of the luminaire is dependent on the use of the correct type of high temperature Nickel Cadium
battery.
o
Battery life may be impaired if the luminaire is mounted in an ambient temperature greater than 25 C. Store the
o o
luminaire or battery between O C and 25 C. Replace with high temperature Nickel Cadium battery to the
manufacturer's recommended part number. Take care not to damage the sleeving. The battery should be replaced
when the rated duration is no longer achieved.
Warning: When disposing of the battery do not pierce, incinerate or short circuit. The battery should be disposed
of in accordance with recognised disposal methods.
Note: The LEDs are non-replaceable but the batteries can be replaced by a competent person.
Luminaire Cleaning
End of Life and Components Disposal
WEEE
IP65
 Product luminaires comply with EN60598-2-22 and are suitable for use in normal interior and exterior conditions,
o o
 For self contained variants - This luminaire has an ambient temperature range of -5 C to 25 C
o o
 For slave variants - This luminaire has an ambient temperature range of -15 C to 40 C
Instruction Leaflet K905V7
i-P65
June 2017
K905V7
Eaton
Wheatley Hall Road, Doncaster, South Yorkshire, DN2 4NB
Sales
T: [phone]
F: [phone]
E: [e-mail]
General
[phone]
[phone]
[e-mail]
International Sales
[phone]
[phone]
[e-mail]
Instruction Manual - K905V7
June 2017
i-P65

230.0mm
Cable Entry
Cable Entry
Cable Entry
Cable Entry
Cable Entry with
Besa entry available
80.0mm
1
2
3
Mounting
Fitting Legend Panel(s) (If Required - ordered seperately)
Wiring
Fixing
Standard Fitting
Double Sided Legend Fitting
Take base of fitting,
knock through the
preferred cable entry
point, Note: centre
cable entry requires
drilling.
Then use 4 x suitable
mounting screws
(not supplied) and
secure fitting to
mounting surface
Fit LED geartray
and diffuser into
fitting base and
secure using
4 x allen key screws
NOTE: If using legend panel, refer to
next page before completing this step
Wire mains cable into terminal block on
fitting base as shown in table below
Ensure mains supply is turned off
N
L1
L2
- Earth (Green/Yellow)
- Neutral (Blue)
- Unswitched Live (Black)
- Switched Live (Brown)
a
bc
a
bc
a. Take required legend with self adhesive backing and attach to
removable legend panel.
b. Fit legend panel into lens by squeezing sides in and releasing
when flush against lens face.
c. Click the geartray, LED side into lens, ensuring light pipe in
the lens is alligned with the LED in the geartray and follow
installation step 3 to complete installation.
a. Take required legend with self adhesive backing
and attach to removable legend panel.
b. Slide removable panel into on side of the double
sided lens, ensuring it is supported by clips.
Repeat this process with second legend panel
on other side of lens.
c. Click the geartray, LED side into double
sided lens, ensuring light pipe in the lens is
alligned with the LED in the geartray and follow
installation step 3 to complete installation.
L2 --
L1 L1 L1
NNN
Self
Contained Slave Ceag
Maintaining IP Rating - Take care when mounting to retain the
IP rating. This can be acheived by using the outboard mounting
holes and appropriate cable gland.
Maximum Torque 2.5Nm