Eaton 3S850 Assembly instructions

ENGLISH
Eaton 3S
Advanced User Guide
Copyright © 2019 EATON
All rights reserved.
614-09405-01_EN
3S EMEA

Page 2
Special symbols
The following are examples of symbols used on the UPS or accessories to alert you to important
information:
DANGEROUSVOLTAGE - Observe the warning associated with the risk of electric shock symbol.
Important instructions that must always be followed.
Information, advice, help.
Read the documentation provided.
Disconnect input plug.
This equipment should only be used in a dry indoor environment.
+ 40 °C
0 °C Operating range of temperature.
0%
85%
Operating range of humidity.
The UPS and their batteries must be kept in a ventilated place.
614-09405-01- 3S EMEA_EN

Page 3
ENGLISH
Contents
1. Introduction....................................................................................... 4
2. Presentation ...................................................................................... 5
3. Installation ........................................................................................ 6
3.1 Package contents...........................................................................................................6
3.2 Recommended positions...............................................................................................6
4. Connection ........................................................................................ 7
4.1 Power supply cord / socket............................................................................................7
4.2 Protected outlets / Backup & Protected outlets ...........................................................7
4.3 Tel / xDSL surge protection (optional) ............................................................................7
4.4 USB COM port (optional) ...............................................................................................8
4.5 USB charging port (optional) ..........................................................................................8
4.6 ON/OFF button ..............................................................................................................8
4.7 Register warranty...........................................................................................................8
5. Operation........................................................................................... 9
5.1 Battery charge ...............................................................................................................9
5.2 AC-power disturbance ...................................................................................................9
5.3 Protected outlets ...........................................................................................................9
5.4 Equipment Care .............................................................................................................9
5.5 Battery replacement .....................................................................................................9
6.Troubleshooting ...............................................................................11
7. Service and support ........................................................................ 12
8. Specication and technical characteristics .................................. 13
9. Glossary........................................................................................... 14
614-09405-01- 3S EMEA_EN

Page 4
1. Introduction
Thank you for selecting an Eaton product to protect your equipment.
The Eaton 3S range has been designed with the utmost care. We recommend that you take the time to read
this advanced user guide and documentations provided to take full advantage of the many features of your
UPS (Uninterruptible Power System).
Before installing your Eaton 3S, please read the information and safety instructions provided. Follow the
instructions in the quick start guide and if necessary, refer to this advance user guide.
To discover the entire range of Eaton products, we invite you to visit our web site at eaton.com or contact
your Eaton representative.
The Eaton 3S Uninterruptible Power System (UPS) is designed for computers and their peripherals, NAS,
televisions, internet gateways, etc... It must not be used to supply other electrical equipment (lighting,
heating, household appliances, etc.). It prevents your critical equipment from power problems such as power
failures and power surges.
614-09405-01- 3S EMEA_EN

Page 5
ENGLISH
2. Presentation
6
7
5
4
9
8
10
3
1 2
1Protected outlets
2Backup & Protected outlets
3UPS status LED
4Protection circuit breaker
5Power supply cord / socket
6Surge protection LED
7Tel / xDSL surge protection (optional)
8USB COM port (optional)
9ON/OFF button
10 USB charging port (optional)
614-09405-01- 3S EMEA_EN

Page 6
3.1 Package contents
11 Eaton 3S UPS
12 Quick start
13 Information and safety instruction
14 USB cable (for Eaton 3S with communication feature: 3S550, 3S700 and 3S850)
15 2 x Output cables (IEC models only)
450
550
700
850
Quick Start
EWOK
11
14
12 13
15
3.2 Recommended positions
Eaton 3S can be wall-mounted, horizontal or vertical position, the distance between screws are 230 mm for
3S450 / 3S550 models and 240mm for 3S700 / 3S850 models.
Ø 8 mm max.
230 mm 450-550 VA
240 mm 700-850 VA
For 3S450 and 3S550 only do not dispose the product on the side as shown below.
3. Installation
614-09405-01- 3S EMEA_EN

Page 7
ENGLISH
4. Connection
4.1 Power supply cord / socket
Connect the UPS to the AC-power source through a wall outlet equipped with an earth connector, using the
attached cord for a UPS with FR / DIN sockets or the supply cord of your computer for a UPS with IEC sockets.
OFF
OFF
FR / DIN IEC
4.2 Protected outlets / Backup & Protected outlets
Plug critical equipment (computer, monitor, modem, etc.) to the backup & protected outlets 2providing
battery backup power and surge protection, taking care not to exceed the rated current indicated in amperes.
Other devices (printer, scanner, fax, etc.) can be connected to the protected outlets 1that provide surge
protection only. The protected outlets are not backed up by battery power in the event of a power outage.
Equipment connected to these outlets is supplied as soon as the AC cord is plugged in.These are not affected
by ON/OFF button 9.
2
1
4.3 Tel / xDSL surge protection (optional)
Protect your Tel / xDSL line using a RJ11 cable (not provided) from the wall phone plug to the Eaton 3S
“In”port 7then connect your device to the Eaton 3S “Out” port 7.
7
614-09405-01- 3S EMEA_EN

Page 8
4.4 USB COM port (optional)
Connect the UPS to the computer using the USB cable 14 supplied.
Enhance your purchase by downloading the conguration tool software using URL :
HTTPS://powerquality.eaton.com/EMEA/support/software-drivers/default.asp
COM models
8
14
14
4.5 USB charging port (optional)
Connect your device to the USB charging port 10 (2A maximum).
USB
10
4.6 ON/OFF button
Switch on the UPS by pressing ON/OFF button 9during 1.5 second.
93
4.7 Register warranty
Register warranty at www.powerquality.eaton.com/EMEA/Product-Registration.
4. Connection
614-09405-01- 3S EMEA_EN

Page 9
ENGLISH
5. Operation
5.1 Battery charge
The UPS charges the battery as soon as it is connected to the AC outlet, whether ON/OFF button 9is pressed
or not. When used for the rst time, the battery will only provide its maximum autonomy after it has been
charged for 8 hours. It is recommended that the UPS be permanently connected to the AC power supply to
ensure the best possible autonomy.
5.2 AC-power disturbance
If AC power is disturbed or fails, the UPS continues to operate on battery power. UPS status LED 3ashes
green. In normal mode, the audio alarm beeps every ve seconds, then every two seconds when the end of
battery backup time is near.
If the power outage lasts longer than the battery backup time, the UPS shuts down and automatically restarts
when power is restored. Following a complete discharge, 10 hours are required to recharge the battery back
to full backup time.
To save battery power, it is possible to press ON/OFF button 9to cut the supply of power to the devices
connected to the battery backup outlets.
5.3 Protected outlets
All protected outlets 1provide surge protection, whatever the position of ON/OFF button 9. The Surge
protection LED 6provide the status of the protection. When the Surge protection LED 6is OFF your
protection is defective, please contact after sales services or local representative.
5.4 Equipment Care
For full battery life, keep the equipment at an ambient temperature of 25 °C (77 °F). Battery service life is
reduced by 50 % for every ten degrees above 25 °C.
If the UPS requires any type of transportation, verify that the UPS is turned off.
5.5 Battery replacement
For battery replacement follow Eaton instructions provided on www.eaton.eu/BatteryServices.
The following precautions should be observed when working on batteries:
• shut down the UPS (ON/OFF button 9),
• disconnect the source prior to connecting or disconnecting battery terminals,
• do not wear any metal objects including watches and rings,
• do not lay tools or metal parts on top of batteries,
• it is imperative to use the same battery type and number.
CAUTION: Batteries present a risk of electrical shock or burn from high short circuit current. Observe proper
precaution. Batteries may contain HIGH VOLTAGE and CORROSIVE, TOXIC and EXPLOSIVE substances.
Because of the battery the output receptacles may carry high voltages even when the AC supply is not
connected to the UPS. Do not dispose of batteries in a re. When exposed to ame, batteries may explode.
Do not open or mutilate the battery or batteries. Released electrolyte is harmful to the skin and eyes and may
be extremely toxic.
614-09405-01- 3S EMEA_EN

Page 10
5. Operation
Battery change :
OFF
A
C
E
F
D
B
Warning: take care not to reverse the polarity + (red) and - (black) when connecting the batteries as this will
destroy the device.
614-09405-01- 3S EMEA_EN

Page 11
ENGLISH
6. Troubleshooting
The Eaton 3S is designed for durable, automatic operation and alerts you whenever potential operating problem may
occur.
The following table describes typical conditions:
Problem Possible cause Action
The battery backup outlets 2
are not supplied with power.
ON/OFF Button 9is not pressed. Press ON/OFF button 9for 1.5 seconds
and check that LED 3turns to green.
The connected devices are not
supplied when AC power fails.
The devices are not connected to the
battery backup outlets 2.
Connect the devices to the battery backup
outlets 2.
AC power is available, but
the UPS operates on battery
power.
Circuit breaker 4has been tripped by an
overload on the UPS output.
Disconnect excess equipment and reset
the circuit breaker 4by pressing the
corresponding button.
The filtered outlets 1and 2
are not supplied.
The wall outlet is not supplied.
Circuit breaker 4has been tripped by an
overload on the UPS output.
Supply power from the wall outlet.
Disconnect excess equipment and reset
the circuit breaker 4by pressing the
corresponding button.
Green LED 3flashes every 1
second and audio alarm beeps
every 5 seconds.
The UPS frequently operates on battery
power because the AC power source is of
poor quality.
Have the electrical installation checked
by a professional or use another wall
outlet.
Green LED 3flashes every 1
second and audio alarm beeps
every 1 second.
The UPS battery backup outlets 2are
overloaded.
Disconnect excess equipment connected
to the battery backup outlets.
Red LED 3is on and the audio
alarm beeps continuous.
A fault has occurred on the UPS. The
battery backup outlets 2are no longer
supplied.
Contact Eaton service and support.
The telephone line is disturbed
or modem access is not
possible.
Surge protection LED 6is
OFF.
Surge protection on the telephone line is
no longer provided.
Disconnect the telephone line from the
wall outlet.
Contact Eaton service and support.
USB communication fails. Cable connection may be defective. Re-connect the USB cable 14 , if still
not available Contact Eaton service and
support.
USB charger ports 10 are not
supplied.
The battery voltage is too low. Recharge the battery, if still not available
contact Eaton service and support.
614-09405-01- 3S EMEA_EN

Page 12
7. Service and support
If you have any question or problem with the UPS, call Eaton or your local service representative in your country / region.
Please have the following information ready when you call for service:
• model number,
• serial number,
• date of failure or problem,
• symptoms of failure or problem,
• customer return address and contact information,
• description of the installation.
614-09405-01- 3S EMEA_EN

Page 13
ENGLISH
Eaton 3S 450 550 700 850
UPS power 450 VA / 270 W 550 VA / 330 W 700 VA / 420 W 850 VA / 510 W
Input mains voltage 220 - 240 V~ ; Ph + N + PE
Input voltage range 184 - 264 V, adjustable to 160 - 284 V
Input frequency 50 / 60 Hz (46 - 65 Hz working range)
Input protection 10 A (thermal breaker)
Output Voltage for backup
outlets
220 V / 230 V / 240 V ~
Output Current for backup
outlets
2 A 2.4 A 3 A 3.7 A
Total output current for all
outlets
9 A maximum
Performance Classification VFD SY 333
Battery 12 V; 4.5 Ah 12 V; 5 Ah 12 V; 7 Ah 12 V; 9 Ah
Communication interface NA USB port (cable included)
USB Charge NA NA 2 USB ports 2 A maximum
Telephone surge protection NA NA T3 Uoc = 6 kV; Up < 1.5 kV; In = 3 kA
Power surge protection T3 Uoc = 6 kV; Up < 1.5 kV; In = 3 kA
Operating temperature 0 to 40 °C
Storage temperature -25 °C to +55 °C
Operating relative humidity Operating relative humidity 0 to 85 %
Operating elevation 0 to 3000 m
Compliances IEC 62040-1; IEC 62040-2 C2*; IEC 62040-3; IEC 62040-4; IEC 61643-11 T3
Conformity
8. Specification and technical characteristics
Warranty 2 years
Weight 2.9 kg 3.2 kg 4 kg 4.3 kg
Dimensions 325 x 140 x 86 mm 335 x 170 x 86 mm
*Note:
The Eaton 3S is a IEC 62040-2 cat C2 UPS product. In a residential environment, this product may cause radio interference,
in which case the user may be required to take additional measures. Output cables should not exceed 10 m length.
CE / EAC / Ukr (DIN models)
CE / Cm (FR models)
CE / EAC / Cm / Ukr (IEC models)
614-09405-01- 3S EMEA_EN

Page 14
9. Glossary
Backup time Time during which the load can be supplied by the UPS operating on battery
power.
UPS Uninterruptible Power Supply.
614-09405-01- 3S EMEA_EN

Page 15
ENGLISH
614-09405-01- 3S EMEA_EN

Page 16 614-09405-01- 3S EMEA_EN