Eaton 5E700UD-KR Assembly instructions

Eaton 5E
Advanced User Guide
5E700UD-KR
5E1200UI-KR
5E1600UI-KR
5E2200UI-KR
Copyright © 2023 EATON
All rights reserved.
DSD-5E2209 English

Contents
1Special symbols ................................................................................................1
2Introduction ..................................................................................................... 2
2.1 Environmental protection .......................................................................... 2
2.2 Benefits ...................................................................................................... 3
3Presentation ..................................................................................................... 4
3.1 Standard installation .................................................................................. 4
3.2 Front panel ................................................................................................5
3.3 Rear panel ..................................................................................................5
4Installation........................................................................................................ 6
4.1 Inspecting the equipment .......................................................................... 6
4.2 Recommended positions............................................................................ 7
4.3 UPS connection .......................................................................................... 7
4.4 USB COM port ............................................................................................9
5Operation ....................................................................................................... 10
5.1 Start-up and normal operation................................................................. 10
5.2 Starting the UPS on battery...................................................................... 11
5.3 UPS shutdown ..........................................................................................11
5.4 Operating modes...................................................................................... 12
5.5 Return of AC input power ........................................................................12
6UPS maintenance ........................................................................................... 13
6.1 Equipment care ........................................................................................ 13
6.2 Storing the equipment ............................................................................. 13
6.3 Recycling the used equipment ................................................................. 13
7Troubleshooting ............................................................................................. 15
7.1 Service and support .................................................................................16
8Specification and technical characteristics ..................................................... 17
8.1 Electrical input .........................................................................................17
8.2 Electrical output ....................................................................................... 17
8.3 Battery...................................................................................................... 18
8.4 Environmental and safety.........................................................................18
9Glossary..........................................................................................................20

1
1 Special symbols
The following are examples of symbols used on the UPS or accessories to alert you
to important information:
DANGER: Dangerous voltage levels are present within the UPS. The UPS
has its own internal power source (the battery). Consequently, the pow-
er outlets may be energized even if the UPS is disconnected from the AC
power source.
Important instructions that must always be followed.
CAUTION: Batteries present a risk of energy or electrical shock or burn
from high short circuit current. Observe proper precaution. Batteries
may contain HIGH VOLTAGE and CORROSIVE, TOXIC and EXPLOSIVE
substances.
Information, advice, help.
Read the documentation provided.
Disconnect input plug.
Before maintenance, first shut down the UPS then disconnect the AC
power source, internal and external batteries then discharge capacitors
by pressing the ON button and wait 5 minutes.
This equipment should only be used in a dry indoor environment.
Operating range of temperature.
85%
0%
Operating range of humidity.
The UPS and their batteries must be kept in a ventilated place.

2
2 Introduction
Thank you for selecting an Eaton 5E product to protect your electrical equipment.
The Eaton 5E range has been designed with the utmost care. We recommend that
you take the time to read this advanced user guide to take full advantage of the
many features of your UPS (Uninterruptible Power System).
Before installing your Eaton 5E, please read the information and safety instruc-
tions provided. Follow the instructions in the quick start guide and if necessary,
refer to this advance user guide.
To discover the entire range of Eaton products, we invite you to visit our web site
at eaton.com or contact your Eaton local representative.
2.1 Environmental protection
Eaton has implemented an environmental-protection policy. Products are devel-
oped according to an eco-design approach.
2.1.1 Substances
This product does not contain CFC and HCFC. This product does not contain as-
bestos. This product is compliant with regulations on the restriction of the use
of substances in electrical and electronic equipment.
2.1.2 Packaging
To improve waste treatment and facilitate recycling, separate the various packing
components.
•The cardboard we use comprises over 50% of recycled cardboard.
•Plastic bags are made of polyethylene.
•Packing materials are recyclable and bear the appropriate identification symbol
.
Materials Abbreviations
Number in the symbols 01
Polyethylene terephthalate PET 01
High-density polyethylene HDPE 02
Polyvinyl chloride PVC 03
Low-density polyethylene LDPE 04
Polypropylene PP 05
Polystyrene PS 06
01

3
Follow all local regulations for the disposal of packing materials.
2.1.3 End of life
Eaton will process products at the end of their service life in compliance with
local regulations. Eaton works with
companies in charge of collecting and eliminating our products at the end of their
service life.
2.1.4 Product
The product is made up of recyclable materials. Dismantling and destruction
must take place in compliance with all local regulations concerning waste. At
the end of its service life, the product must be transported to a processing cen-
ter for electrical and electronic waste. eaton.com/recycling
2.1.5 Battery
The product contains lead-acid batteries that must be processed according to
applicable local regulations concerning batteries. The battery may be removed
to comply with regulations and in view of correct disposal.
2.2 Benefits
The Eaton 5E uninterruptible power system (UPS) protects your sensitive electron-
ic equipment from the most common power problems, including power outages,
voltage sags, impulsive transients, line noise, and long-term under and over volt-
age conditions.
Power outages can occur when you least expect it and power quality can be errat-
ic. These power problems have the potential to corrupt critical data, destroy un-
saved work sessions, and damage hardware - causing hours of lost productivity
and expensive repairs.
With the Eaton 5E, you can safely eliminate the effects of power disturbances and
guard the integrity of your equipment. Providing outstanding performance and
reliability, the Eaton 5E’s unique benefits include:
•Standard communication: one USB communication port.
•Backed by worldwide agency approvals.

4
3 Presentation
3.1 Standard installation
3.1.1 Weights and dimensions
Description (UPS) Weights (kg / lbs) Dimentions (mm / inch) D x W x H
5E700UD-KR 4.3 / 9.5 288 x 100 x 148 / 11.5 x 3.9 x 5.8
5E1200UI-KR 8.2 / 18.2 330 x 133 x 180 / 13.0 x 5.2 x 7.1
5E1600UI-KR 8.9 / 19.6 330 x 133 x 180 / 13.0 x 5.2 x 7.1
5E2200UI-KR 10.0 / 22.0 330x 133 x 180 /13.0 x 5.2 x 7.1

5
1
1
3
2
2
5E1200UI- KR
5E1600UI-KR/5E2200UI-KR
3.2 Front panel
3.3 Rear panel
1. USB communication port
2. ON/OFF Button
3. UPS status LED
1
AC Input
3
Fan
2
AC Output
KR
2 3

6
4 Installation
4.1 Inspecting the equipment
If any equipment has been damaged during shipment, keep the shipping cartons
and packing materials for the carrier or place of purchase and file a claim for ship-
ping damage. If you discover damage after acceptance, file a claim for concealed
damage.
To file a claim for shipping damage or concealed damage:
1. File with the carrier within 15 days of receipt of the equipment;
2. Send a copy of the damage claim within 15 days to your service representative.
Check the battery recharge date on the shipping carton label. If the date has
passed and the batteries were never recharged, do not use the UPS. Contact
your service representative.
4.1.1 Package content
Verify that the following addi-
tional items are included with the
UPS:
1. UPS
2. Connection cables (IEC
model only)
3. Instructions and Safety Infor-
mation
4. Quick start
IEC model only

7
4.2 Recommended positions
Place the Eaton 5E on a flat, stable surface in its final location. Always keep 6” or
150 mm of free space near UPS openings for ventilation.
Installation in tower position
4.3 UPS connection
4.3.1 Power supply connection
Check that the indications on the name plate located on the back of the UPS
correspond to the AC-power source and the true electrical consumption of
the total load.
Connect the UPS to the AC-power source with cable through a wall outlet equipped
with an earth connector, using your equipment cord.
1. Disconnect the protected equipment, keep the power cable
2. Connect IEC cable on protected equipment side.
3. Connect IEC cable provided on UPS AC output side
4. Connect the power cable to UPS AC inlet
5. Connect the power cable to wall outlet

8
4.3.2 Protected outlets / Backup & Protected outlets
Plug critical equipment (computer, monitor, modem, etc.) to the backup & pro-
tected outlets providing battery backup power, taking care not to exceed the rated
current indicated in amperes.
IEC
1
5
2
4
3
DE

9
Equipment connected to these outlets is supplied as soon as the AC cord is plugged
in. These are not affected by ON/OFF button.
4.4 USB COM port
Connect the UPS to the computer using the USB cable.
Enhance your purchase by downloading the monitoring software “Eaton UPS Com-
panion” using URL : eaton.com/downloads

10
5 Operation
5.1 Start-up and normal operation
Check that the indications on the name plate located on the back of the UPS
meets to the AC power source and the true electrical consumption of the
total load.
5.1.1 Battery charge
The UPS charges the battery as soon as it is connected to the AC outlet, whether
the ON/OFF button is pressed or not. It is recommended that the UPS be perma-
nently connected to the AC power supply to ensure the best possible autonomy.
5.1.2 Button function:
1. Buzzer mute:
Push the button for <2s to mute the buzzer temporarily when there is a fault occur
or battery test fail.
2. UPS on/off:
Push the button for >2s, then to power on/off the UPS.
3. Silence mode:
Let UPS working in the standby mode, then to push the button for >11s to enter
the configuration mode.
To start the UPS:
1. Verify that the UPS power cord is plugged in.
2. There is a single buzzer indication.
3. Press the button on the UPS front panel for few seconds.
Check the UPS front panel display for active alarms or notices. Resolve any active
alarms before continuing; if the indicator illuminates in red, do not proceed
until all alarms are clear (see “Troubleshooting” section). Check the UPS status
from the front panel to view the active alarms. Correct the alarms and restart if
necessary.

11
4. Verify that the indicator illuminates in green, indicating that the UPS is op-
erating normally and any loads are powered and protected. The UPS should be
in Normal mode.
5. The UPS will make a first battery test, the will blink for few seconds, this
behavior is normal
ON
5.2 Starting the UPS on battery
To start the UPS on battery:
1. When the UPS is disconnected from the AC power source, press the button
on the UPS front panel. The UPS transfers from Standby mode to Battery mode.
The indicator blinking and the buzzer snooze.
The UPS supplies power to your equipment.
2. Check the UPS front panel display for active alarms or notices besides the “Bat-
tery mode” and related notifications that indicates missing utility power. Re-
solve any active alarms before continuing. See “Troubleshooting”.
Check the UPS status from the front panel to view the active alarms. Correct the
alarms and restart if necessary.
5.3 UPS shutdown
To shut down the UPS:
Press the button on the front panel for two seconds. UPS starts to beep and
indicator is blinking. The UPS then transfers to Standby mode, and the indicator
turns off.
> 2 s

12
5.4 Operating modes
The Eaton 5E front panel indicates the UPS status through the UPS LED indicator.
5.4.1 Normal mode
When the symbol is illuminated in green, the UPS is providing protected AC
power output. The UPS charges the batteries and provides power protection to
your equipment.
5.4.2 Battery mode
When the UPS is operating during a power outage, the alarm beeps once every
five seconds and the indicator illuminates blinking.
The necessary energy is provided by the battery.
When the utility power returns, the UPS transfers to Normal mode operation while
the battery recharges. If battery capacity becomes low while in Battery mode, the
audible alarm beeps faster.
This warning is approximate, and the actual time to shutdown may vary signifi-
cantly; gracefully shutdown all applications on connected equipment due to immi-
nent UPS shutdown.
When utility power is restored after the UPS shuts down, the UPS automatically
restarts.
5.4.3 Low-battery warning
•The indicator blinking quickly.
•The audio alarm beeps every 1.5 seconds.
The remaining battery power is low. Shut down all applications on the connected
equipment because automatic UPS
shutdown is imminent.
5.4.4 End of battery backup time
•All the LEDs go OFF.
•The audible alarm stops.
5.5 Return of AC input power
Following an outage, the UPS restarts automatically when AC input power returns
(unless the UPS is not shut-down by backup end) and the load is supplied again.

13
6 UPS maintenance
6.1 Equipment care
For the best preventive maintenance, keep the area around the equipment clean
and dust free. If the atmosphere is very dusty, clean the outside of the system with
a vacuum cleaner.
For full battery life, keep the equipment at an ambient temperature of 25 °C (77 °F).
The batteries are rated for a 3-5 year service life. The length of service life varies,
depending on the frequency of usage and ambient temperature (life divided by 2
each 10 °C above 25 °C).
If the UPS requires any type of transportation, verify that the UPS is turned off.
Batteries used beyond expected service life will often have severely reduced run-
times. Replace batteries at least every 4 years to keep units running at peak per-
formance.
Batteries runtime will be reduced at low temperature (below 10 °C).
6.2 Storing the equipment
If you store the equipment for a long period, recharge the battery every 6 months
by connecting the UPS to utility power. The internal batteries charge to 90% capac-
ity in less than 3 hours. However, Eaton recommends that the batteries charge for
48 hours after long-term storage.
Check the battery recharge date on the shipping carton label. If the date has
passed and the batteries were never
recharged, do not use them. Contact your service representative.
6.3 Recycling the used equipment
Contact your local recycling or hazardous waste center for information on proper
disposal of the used equipment. eaton.com/recycling
Do not dispose the battery or batteries in a fire. Batteries may explode.
Proper disposal of batteries is required. Refer to your local codes for
disposal requirements.
Do not open or mutilate the battery or batteries. Released electrolyte is
harmful to the skin and eyes. It may be toxic. Do not discard the UPS or

14
the UPS batteries in the trash. This product contains sealed, lead acid
batteries and must be disposed of properly. For more information, con
tact your local recycling/reuse or hazardous waste center.
Do not discard waste electrical or electronic equipment (WEEE) in the
trash. For proper disposal, contact your local recycling/reuse or hazard
ous waste center.

15
7 Troubleshooting
The Eaton 5E is designed for reliable, autonomous operation while providing you
with notifications and alerts whenever a
potential operational or performance issue occurs.
Usually the alarms shown by the control panel do not mean that the output power
is affected. Instead, they are preventive alarms intended to alert the user.
•Events are silent status information that are recorded into the Event log. Exam-
ple = “AC freq in range”.
•Alarms are recorded into the Event log and displayed on the LCD status screen
with the logo blinking. Some alarms may be announced by a beep every 3 sec-
onds. Example = “Battery low”.
•Faults are announced by a continuous beep and red LED, recorded into the Fault
log and displayed on the LCD with a specific message box. Example = Out. short
circuit.
Use the following troubleshooting chart to determine the UPS alarm condition.
Conditions Possible cause Action
The UPS outlets are
not supplied with
power or the UPS
cannot be turn on
after pressing the
button
The ON/OFF Button is not
pressed or the ON/OFF but-
ton is pressed too briefly.
Press the button continuously for
more than 2 seconds and check
that LED turns to green.
The connected devic-
es are not supplied
when AC power fails.
The devices are not connect-
ed good to the UPS outlets .
Check the cables and reconnect
the devices to the UPS outlets.
Green LED flashes
every 1 second and
audio alarm beeps
every 5 seconds.
The UPS frequently operates
on battery power because
the AC power source is of
poor quality.
Have the electrical installation
checked by a professional or use
another wall outlet.
Green LED flashes
every 1 second and
audio alarm beeps
every 1.5 second.
UPS operates on battery
power with a low battery
The actual time to shutdown may
vary significantly, prepare your
equipment for shutdown.
Battery discharging
time diminishes
Battery not yet been fully
charged or overloaded
Keep UPS connected to utility
power persistently for more than
6 hours to recharge the batteries.
Or remove some noncritical loads.

16
Green/Red LED alter-
native flashes every
0.5 second and audio
alarm beeps every 1.5
second.
The connected loads are
exceed the UPS capacity or
Battery fault
The connected loads are exceed
the UPS capacity, remove some
noncritical loads or check if some
loads are failed.
Red LED is on and the
audio alarm beeps
continuous.
A fan fault has occurred on
the UPS. The UPS outlets are
no longer supplied.
Check if the fan is stopped, if
no, please contact your service
representative.
Red LED is on and the
audio alarm beeps
continuous.
An internal fault has
occurred
on the UPS. The UPS outlets
are no longer supplied.
Contact your service
representative.
USB communication
fails.
Cable connection may be
defective.
Re-connect the USB cable, if still
not available. Contact your
service
representative.
7.1 Service and support
If you have any question or problem with the UPS, call Eaton or your local ser- vice
representative in your country / region. Please have the following information
ready when you call for service:
•Model number
•Serial number
•Firmware version number
•Date of failure or problem
•Symptoms of failure or problem
•Customer return address and contact information
If repair is required, you will be given a Returned Material Authorization (RMA)
number. This number must appear on the outside of the package and on the Bill
Of Lading (if applicable). Use the original packaging or request packaging from the
Help Desk or distributor. Units damaged in shipment as a result of improper pack-
aging are not covered under warranty. A replacement or repair unit will be shipped
freight prepaid for all warrantied units.
For critical applications, immediate replacement may be available. Call the
Help Desk for the dealer or distributor nearest you.